I have a Zermatt origin now, and I would like to build a TL3 to try AW mags but be able to use some of my origin barrels on the TL3. Ray at Zermatt said PVA used to make a ring to move the barrel out .100 so u could do this, since the origin tenon is .100 longer. I was wondering if anyone knew of anyone that currently makes one. I talked to PVA and they said they don't make them any more.
Zermatt origin barrel on TL3 action
- Thread starter Andrew863
- Start date
Hunt’s Long Range lug:
HLR Origin 0.150 Thick Recoil lug | Hunt's Long Range
Here it is! Do you have a Big Horn TL3 and a Big Horn Origin? Do want to be able to swap the barrels between your actions? HLR has your answer! This precision ground 0.150" thick recoil lug will take the place of the 0.250" thick standard lug that comes with the Big Horn Origin.This
huntslongrange.com
(oops sorry wrong way…)
I would think u could but my origin barrels are all proof shouldered pre fits. Im probably going to call in a favor at the machine shop i use to work at if no one can point me in the right direction to buy one. I wish someone would make a lug that was .250 think and had the .100 spacer on the front.
These recoil lugs have been sold out for a minute. Has anyone taken a TL3 barrel and had the shoulder cut back to make it fit an Origin? Seems like you could make it fit a solus by doing this as well.Hunt’s Long Range lug:
HLR Origin 0.150 Thick Recoil lug | Hunt's Long Range
Here it is! Do you have a Big Horn TL3 and a Big Horn Origin? Do want to be able to swap the barrels between your actions? HLR has your answer! This precision ground 0.150" thick recoil lug will take the place of the 0.250" thick standard lug that comes with the Big Horn Origin.This
(oops sorry wrong way…)
I’m in a similar boat. Wanting to use TL3 LA barrels (same dimensions as origin) on a TL3 SA action.
Just about any machine shop should be able to help. But I ended up picking up a few of these and they’re promising:
www.mcmaster.com
They’re all just ever so slightly thicker than 0.1”, which is good. I just need to take them to a flat stone a little bit and then trim down the outer diameter by putting it in the drill press or maybe router.
A local machine shop is definitely the better route though.
Edit: autocorrect
Just about any machine shop should be able to help. But I ended up picking up a few of these and they’re promising:
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
They’re all just ever so slightly thicker than 0.1”, which is good. I just need to take them to a flat stone a little bit and then trim down the outer diameter by putting it in the drill press or maybe router.
A local machine shop is definitely the better route though.
Edit: autocorrect
Last edited:
I dont have access to a surface grinder right now. So I made 2 on the lathe at work and then had a local shop grind them. I gave them a tolerance of +-.00025 and they are all over that. I made them out of 416 stainless and they blend into the barrel perfect.I’m in a similar boat. Wanting to use TL3 LA barrels (same dimensions as original) on a TL3 SA action.
Just about any machine shop should be able to help. But I ended up picking up a few of these and they’re promising:
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
They’re all just ever so slightly thicker than 0.1”, which is good. I just need to take them to a flat stone a little bit and then trim down the outer diameter by putting it in the drill press or maybe router.
A local machine shop is definitely the better route though.
Similar threads
