Search results
-
-
Gunsmithing Part Failure: Swapping Bolts in a 700?
Make damn sure you check the headspace Sent from my iPhone using Tapatalk- gewehr
- Post #3
- Forum: The Armory
-
280AI with Barnes LRX 168grs
Do you know your freebore? Also what speed? Sent from my iPhone using Tapatalk- gewehr
- Post #10
- Forum: Reloading Depot
-
300 WSM, 300 WM, and 300 Wby Mag H2O case capacity?
Nosler lists the h2O capacity of the case with the particular bullet listed seated to saami length not the overfill capacity Sent from my iPhone using Tapatalk- gewehr
- Post #2
- Forum: Reloading Depot
-
3 position safety Remington clone
Sweet Sent from my iPhone using Tapatalk- gewehr
- Post #7
- Forum: Bolt Action Rifles
-
American Rifle's M5 Bolt Action, The Mausingfield
Definitely might have to order one of these bad boys Sent from my iPhone using Tapatalk- gewehr
- Post #46
- Forum: Bolt Action Rifles
-
6.5 Saum build in a Win 70 XTR magnum action can it be done?
Absolutely just make sure to get it tried and it will work out great Sent from my iPhone using Tapatalk- gewehr
- Post #2
- Forum: Bolt Action Rifles
-
Gunsmithing Rem 700 bolt squeak
You could also try a dry lube like lock ease (after it evaporates) Sent from my iPhone using Tapatalk- gewehr
- Post #5
- Forum: The Armory
-
Manufacturers and chamberings
No where near close to consistent Sent from my iPhone using Tapatalk- gewehr
- Post #3
- Forum: Bolt Action Rifles
-
Budget build with the Krylon touch!
Just be careful with solvents cleaning it, krylon is very susceptible to being removed by many splbents Sent from my iPhone using Tapatalk- gewehr
- Post #14
- Forum: Bolt Action Rifles
-
Where to get test bullets?
Brownells has em Sent from my iPhone using Tapatalk- gewehr
- Post #8
- Forum: Reloading Depot
-
Gunsmithing Barrel nut setup on FN/Win Mod 70 ????
It might work on a post 64 push feed Sent from my iPhone using Tapatalk- gewehr
- Post #5
- Forum: The Armory
-
Damn decisions 30-06 300 win
300 win, more zip for heavier bullets Sent from my iPhone using Tapatalk- gewehr
- Post #3
- Forum: Bolt Action Rifles
-
ETA of the 7mm 195gr VLD?
On lrh Eric Stecker said at least a 8.5 twist, though I looked on Bergers calculator and changed the data to match the 195 and found an 8 would probably be best for my environmental conditions Sent from my iPhone using Tapatalk- gewehr
- Post #14
- Forum: Reloading Depot
-
ETA of the 7mm 195gr VLD?
These bullets at this point are like Bigfoot and the Loch Ness monster Sent from my iPhone using Tapatalk- gewehr
- Post #13
- Forum: Reloading Depot
-
75gr amax and 208gr amax in stock at midsouthshooterssupply!!
Sweet Sent from my iPhone using Tapatalk- gewehr
- Post #2
- Forum: Reloading Depot
-
Quick brass drying
I just heat it to 115 and put them in standing overnight, 125 if I want it done faster (1 hour) Sent from my iPhone using Tapatalk- gewehr
- Post #10
- Forum: Reloading Depot
-
300 WM brass?
That's good shit Sent from my iPhone using Tapatalk- gewehr
- Post #18
- Forum: Reloading Depot
-
Gunsmithing Cutting a barrel to 20"
Quick load says 120 ish Sent from my iPhone using Tapatalk- gewehr
- Post #5
- Forum: The Armory
-
Scope advice for my GA Precision Rock
That's a good scope [emoji4] Sent from my iPhone using Tapatalk- gewehr
- Post #16
- Forum: Bolt Action Rifles
