Search results

Search the forum Search Articles
  1. A

    Suppressors Gas in face with can installed!!!! ugghhh help

    Re: Gas in face with can installed!!!! ugghhh help PRI charging handle!, an enhanced bolt carrier will also help a bit but more money than it's probably worth.
  2. A

    Egg at 1000 yards

    Re: Egg at 1000 yards 5 inch groups at 1000 aren't to uncommon. But an egg at 1000? That is beyond most peoples rifles capabilities. I usually shoot at eggs at 500 lol, golf balls at 300 without taking my sweet ass time. Put it this way, I think the bench rest guys might be able to hit that...
  3. A

    Tricks for reloading 223 quick

    Re: Tricks for reloading 223 quick Oh hell yes!, to bad I don't have any room for that. Garage is fulllll. lol. Looking for something I can hide in cabinets. But I like your style.
  4. A

    Which buffer????

    Re: Which buffer???? H2 with tubb cs buffer spring. In my noveske I have the recce, mid length switchblock and rifle length buffer with cs spring.
  5. A

    Rifle Scopes which aimpoint do you think best for cqb?

    Re: which aimpoint do you think best for cqb? The aimpoint / eotech is sort of a preference thing. They are roughly the same idea executed differently. For me the biggest differences came down to profile, weight and battery life. But since you likely won't be using this on a patrol rifle just...
  6. A

    Gunsmithing Brass Punch Help...

    Re: Brass Punch Help... If you want to get a full set. Make sure you get "roll pin punches". They center on the pins and make your life easier, I got a set from amazon that were decent for like 25, and a starter pin set for about 40? The starter pin punches aren't required but will make...
  7. A

    Gunsmithing AR 15 Armeror school

    Re: AR 15 Armeror school I haven't been to armorers school. But you are a mechanically oriented person you can basically learn how to build a rifle on youtube. Building a complete rifle isn't hard at all. The pain is getting all the pin punches, vise blocks and m16 armorers wrench. Just a...
  8. A

    Gunsmithing Gunsmith might have fouled my Surefire Flash Hider

    Re: Gunsmith might have fouled my Surefire Flash Hider well I would be a prick about it and make them take care of it. You certainly didn't hand it to them like that unless you went at it with a car battery and jumper cables... hack job on a 150 dollar break. I have one on the end of my rifle...
  9. A

    Gunsmithing Objective research on Barrel Break-in procedures

    Re: Objective research on Barrel Break-in procedures For the initial break in the idea is to remove burs etc that cause copper fouling. Sometimes for various reasons one or all of the lands pick up copper. Breaking in a barrel isn't required. Even in the field manuals they say given the...
  10. A

    favorite 308 load for 600+ out of a 20" barrel?

    Re: favorite 308 load for 600+ out of a 20" barrel? 43.5 varget, 178 a max, 2.815, BR2 iirc. load down 10% and start there.
  11. A

    "Blend" a bench into the living room? LOL

    Re: "Blend" a bench into the living room? LOL I think I saw a really nice work bench custom made out of butcher block. Looked like normal living room cabinet. Wasn't cheap but looked high end to match furniture. I recently said F-it and drilled a bunch of holes in the dining room table for...
  12. A

    Varget or RE15 for .223

    Re: Varget or RE15 for .223 If you load in batches for the season, Rock varget cause match to match you will have minimal difference throughout. The down side is there has been some lot to lot variance. But at any given shoot you will have guys doing well with both powders. Buy a lb of each...
  13. A

    AR Powders for: .223 55gr-69gr meters well

    Re: AR Powders for: .223 55gr-69gr meters well Since you have both 308 and 223. I would say rock Ramshot Tac... good stuff and meters very well. If trickling it's hard to beat varget for low es and temperature stability.
  14. A

    Tricks for reloading 223 quick

    Re: Tricks for reloading 223 quick I have a new 650 with case feed, and I can tell you one thing. It's fucking bad ass for 223, not so much for 9mm. Gotta find a fix for it spilling a little powder on the down stroke(when it's finishing indexing). It's a freegin monster, now I just have to...
  15. A

    Photos More!

    Re: More! That's kinda sexy..
  16. A

    Remington selling refurbished military M24s

    Re: Remington selling refurbished military M24s No love for DM's lol
  17. A

    Question from Pacific Tool & Gauge....

    Re: Question from Pacific Tool & Gauge.... Petey, from looking at it. It looks like you could install with roll pin punch.
  18. A

    My creation of civilian version of Mk 262 Mod m1n3

    Re: My creation of civilian version of Mk 262 Mod m1n3 Update, I had an issue with one of the rifle components / weather. Weather should break from the rain this coming week so I can get out to the range (problem is that I live in the rainy NW and the firing lines are covered but the...
  19. A

    Practical Rifle @ TriCounty this Saturday

    Re: Practical Rifle @ TriCounty this Saturday Watching the video it looks like spotter zombie mash 2012 lol.
  20. A

    Practical Rifle @ TriCounty this Saturday

    Re: Practical Rifle @ TriCounty this Saturday Looking fun kids, I should be getting my recievers back from noveske monday, build monday night and do load development sunday. Hope to be out playing with you guys soon!
Top Bottom
Back
Home
Forums
Merch
Alerts