Search results

Search the forum Search Articles
  1. G

    375 CT neck help

    As a public service announcement... I called Whidden to inquire about their FL sizer. It was stated that the neck dimension is 0.395". I purchased one and measured the neck dimension on my brass after sizing at 0.3985". Not a slam against Whidden but this is the dimension of their FL die...
  2. G

    Reloading Equipment WTS: PTG FL .375 CT Dies

    Going a different route. $150 shipped. USPS money order or PayPal f&f. No box or case was provided with them. They'll arrive to you as they arrived to me from PT&G.
  3. G

    Labradar error 23049

    I sent the unit in for repair and they sent me another unit. Not a "new" unit but a different one. It powers on and arms without the error code at least. I haven't had the chance to take it out yet.
  4. G

    Bergers 140 Gn.. Can't find load data.

    What cartridge?
  5. G

    375 CT neck help

    I have no way to pull a 375 bullet from a case. All I can do at this point is measure the o.d. of the brass that has a bullet seated. The one piece of Peterson brass that I have, has a Berger 379 seated to get the oal I desired. When I measure the o.d. of the neck, where the bullet is located...
  6. G

    Reloading Equipment SPF: AB 375 CT dies

    $325 shipped. I loaded 25 rounds with them. As new. PayPal f&f or usps money order.
  7. G

    375 CT neck help

    I have 100 pcs of Bertram 375 brass. I have a set of Applied Ballistics and PTG FL dies. I have one piece of Peterson brass for comparison. The neck diameter of a loaded round in Peterson brass measures 0.405". Loaded neck in Bertram brass is just under 0.400". My AB dies size the Bertram...
  8. G

    What did you do in the reloading room today?

    Worked up some 375 CT test loads with 379 gr Bergers. Working with seating depth.
  9. G

    Labradar error 23049

    I've owned a LR for a couple of years. Today was the third time I took it out and it wouldn't arm. This thing has frustrated me every time it leaves the house. I just bought a JKL trigger system for it in hopes to lessen my frustration. The trigger will be here next week... Is there a reset...
  10. G

    Hornady 375 cal 390 grain A-TIP G7 .497

    If these shorter bullets perform, this will turn the 375CT into an Enabler. Only better!!! GAME CHANGA' !!!
  11. G

    375 solids, jump tolerant?

    Thanks again. I'll do some figuring with quickload.
  12. G

    375 solids, jump tolerant?

    Thanks, Geno. I also have some N570 and RL50 but figured they were too slow.
  13. G

    375 solids, jump tolerant?

    I'm trying not to reinvent the wheel here and I'd like to get your real world experience. I've found my lands and I'm trying to determine a good starting point. 0.030" off? 60 off? 120 off? Is there a rule of thumb for solids? Standard 375 CT. I have both CE 400 lasers and Berger 379 solids...
  14. G

    Hotness for 2020?

    375 CT
  15. G

    Sidearms & Scatterguns Savage's New Semi-Auto Shotgun "RENEGAUGE"

    "Perfected over several years"? How's could it take several years to copy an already existing gas system? There are plenty of good working gas guns to reverse engineer. "A light balanced system that swings easy, hits hard". Duh. A lightweight 12 gauge system is going to "hit hard". Your...
  16. G

    Optics SOLD Nightforce mount 30mm 1.375” SOLD

    I’ll take it. PM sent. Thanks @Tricky Dickey
  17. G

    Accessories Found: NF unimout 30mm 20 moa 1.375"

    BTT
  18. G

    Accessories Found: NF unimout 30mm 20 moa 1.375"

    FOUND ONE. Thanks.
  19. G

    1500 with 7 rm and 6.5m? Possible ?

    As already stated, 7 mag and CM will hit an ipsc sized target if you do your part. Pay attention to the conditions.
  20. G

    Magnetospeed V3 or Labradar?

    I've only taken my LR out twice in the past year. It frustrates me to no end. I can't get it to consistently pick up suppressed shots. I'm also getting ready to start load development for a 416 Barrett and 375 CT. Both have terminator brakes and I'm afraid of blowing the LR apart with their...
Top Bottom
Back
Home
Forums
Merch
Alerts