Search results

Search the forum Search Articles
  1. C

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Thanks Russ, I hope so too. You have probably one of the best people I've worked with in the firearms industry. I don't expect anyone to go to the lengths that you have but it would be nice if they were as prompt as you are with your responses.
  2. C

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    DTA are some of the finest people in the industry and there really is no other rifle like it on the market.
  3. C

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    DTA is good people
  4. C

    Nemo Rifles: Considering becoming a dealer

    What kind of accuracy are we talking about here? Do they have an accuracy guarantee?
  5. C

    338 Lapua & 300gr Sierra Match King

    300gr SMK 92gr H1000 CCI primer 3.700 COAL(IIRC) Lapua brass 26" bbl 2700fps
  6. C

    New reloading strategy, comments wanted.. :)

    This is what I have been doing. I will say that if it's windy out you're going to want to be inside while weighing your powder charge. If I'm working with non-extruted powders I'll just take my Redding BR powder measure and if extruted then I'll take the charge master and use it inside our high...
  7. C

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    Oops, I knew that. Don't know what I was thinking. Thanks Russ, you've been a big help through all of this.
  8. C

    Official (DTA) SRS, HTI, Covert, Hunter Thread

    DTA is good people
  9. C

    Share your DTA loads!

    New conversion en route and is looking mighty promising. :D
  10. C

    Share your DTA loads!

    New conversion en route and is looking mighty promising.
  11. C

    Benchmark?

    110 GR. BAR TSX FB Hodgdon Benchmark .308" 2.690" START-45.2gr 3005fps 39,700 PSI MAX-50.2grs compressed 3316fps 54,200 PSI data from here: Cartridge Loads - Hodgdon Reloading Data Center - data.hodgdon.com
  12. C

    Suppressors Anyone use Bowers suppressor covers?

    So do they prevent heat raising up from the suppressor and causing a mirage effect in the scope?
  13. C

    Benchmark?

    Can't remember what my starting load was but I ended up at 49.2grs of benchmark pushing a 110gr Vmax at 3217fps. You'd want to work up to that of course.
  14. C

    Share your DTA loads!

    I'm gonna load some of these up tonight. I know you don't measure COAL via the tip of the bullet, but i don't have the means to measure from the ogive. Do you know approximately what the COAL would be from the tip? Nice thing about my range is that we have a highpower building where I can plug...
  15. C

    Share your DTA loads!

    Wow, that's quite the jump. I usually seat mine to 2.845. I took out my 16" .308 and tried my load from the OP(178gr Amax w/44.5grs Varget). It really didn't do too well. About 1.25 OAL if not worse. I have some 175gr SMKs I think I might try out. Russ said the Covert barrels seem to like that...
  16. C

    Emergency Iron Sites

    True, I would like open notch sights. I don't like the idea of a diopter sight mounted that far forward. I used to run a Aimpoint H1 at 45 degrees on another scoped AR and burned multiple coyotes at less than 25yds with it. IMO that is the way to go. My only beef with a setup like that is that...
  17. C

    Emergency Iron Sites

    I had this happen to me just this last season using a suppressed AR. I shot it in the gut through my 2.5-10x24 on the lowest setting. It ran straight at me(due to the suppressor I imagine) and I had to roll the rifle counter-clockwise and put another in it at about 10-15ft away from the cedar...
  18. C

    Benchmark?

    I use it with the 110gr Vmax. It works great with that.
  19. C

    60 Gr. VMAX Powder Help

    The granules are about half the size of Varget. They meter pretty well for me.
  20. C

    60 Gr. VMAX Powder Help

    Bingo. I've been using Benchmark for years and it works great.
Top Bottom
Back
Home
Forums
Merch
Alerts