Search results

Search the forum Search Articles
  1. Eric_F

    Reloading Equipment Free .284 168gr mk

    I'll take them if Todd doesn't.
  2. Eric_F

    Gunsmithing Freebore needed for 115dtac dasher

    Again I'm not sure. You could probably calculate where the base would end up given the DTAC tip to 0.242" ogive distance is 0.64" and the overall length is 1.295": https://www.6mmbr.com/DTAC115hbc.html That means a 0.125" fb and 0.060" jump would put the base at: 1.295 - 0.64 - 0.125 + 0.060 =...
  3. Eric_F

    Gunsmithing Freebore needed for 115dtac dasher

    I'm not sure on freebore, but this shows pretty well that the DTAC performs best with a significant jump (0.060" - 0.080") in a variety of cartridges https://precisionrifleblog.com/2020/04/05/bullet-jump-load-development-data/
  4. Eric_F

    Reloading Equipment Found please delete

    If you use code Cambridge here: https://ceproducts.shop/collections/featured-products/products/fx-120i-reloading-scale-122g-x-0-001g You can get an FX120i for $500 shipped.
  5. Eric_F

    Suppressors Ultra 7 10.5oz Heavy after 28k rounds of 6.5 CM

    I'd bet a power supply like this connected to a peristaltic pump like this would recirculate solvent nicely for about $40. You would likely have to upgrade to an Arduino if you want periodic pumping or spraying.
  6. Eric_F

    Sidearms & Scatterguns Help with a 12 ga auto

    Clamps work of course, but the forend is pretty long especially on the Comp. I like it positioned there, but you'll have to see what feels right.
  7. Eric_F

    Sidearms & Scatterguns Help with a 12 ga auto

    The Hayes custom guns look set up for 3 gun, and >$1600. Nice looking of course, but if you're looking for HD and range toy, go with the factory. I haven't modified the loading port on my Comp and quad load fine. Not competitive in 3 gun really, but the loading port isn't what's holding me back...
  8. Eric_F

    Sidearms & Scatterguns Help with a 12 ga auto

    Good call on the 1301T, I'm sure you'll both love it. I've got the Comp, that thing is super light and soft shooting. Theres a local girl who just rocks 3 gun with one too. My buddy's Versa Max was really soft shooting too, but was heavy as hell and swumg slow, wouldn't recommend it for a...
  9. Eric_F

    3-5 rnd Cartridge loops

    That's enough of a niche thing I think you would have to have it custom made. If you send me $40 and dimensions of the velcro section I'd make one for you. Some shooting bags I made here: https://www.snipershide.com/shooting/threads/diy-sticky-shooting-bags.6945275/
  10. Eric_F

    Reloading Equipment SOLD- Harrell 6mm BRA die

    I'll take it.
  11. Eric_F

    Goldilocks - which "middle" 7mm?

    I like the numbers on the middleweight 7mm cartridges a lot. Great ballistics out to past 1000, great bullet selection for targets or elk hunting, efficient with powder, and not too much recoil. I have brass and dies (though not yet a rifle) for both 280 AI and straight 284 Win. I'll be building...
  12. Eric_F

    Accessories ***SOLD*** WTS 6 BR Imp chamber reamer

    Seconds.
  13. Eric_F

    Reloading Equipment WTB 280AI Reloading Equipment

    I've got Hornady dies, 56 fireformed R-P cases, and 61 fireformed Winchester nickel plated cases I'd sell for cheap. Planned on doing the same but ended up going with 284 Win. PM me if you're interested.
  14. Eric_F

    Accessories WTB tikka T3x compact stock

    PM sent.
  15. Eric_F

    Shelf for Lee turrets

    I thought I'd share a simple storage solution for my extra Lee Turrets. I've got the Classic Turret press, which isn't anything fancy but has been working. One of the best things about it is the super easy swapping of turrets, and that each only costs like $13. The awkward thing is how to store...
  16. Eric_F

    Cheek piece comfort

    Another vote for the self stick neoprene foam pads off Amazon. This was $10 for a 6-pack, 1/8" thick. Clean off the surface well with IPA (or soap and water if it's painted) and it has stuck well for me.
  17. Eric_F

    Reloading Equipment 6mm 6.5 223 projos dies trimmers

    I'll take the MDT mag, PM sent.
  18. Eric_F

    Best d.i.y. option for brass annealing.

    Amazon for the PVC rod and cake pan, eBay and slow boat from from China for the electronics and clamps, hardware store for case material, angle aluminum, U bolt. Here's mine. Here you can see the prox sensor that should theoretically run the case feeder only when it senses there isn't a case...
  19. Eric_F

    Best d.i.y. option for brass annealing.

    That's the PVC rod I listed as case feeder. I drilled a hole in it that just press fit over the motor axle, and then drilled a set screw hole. It being PVC I actually didn't tap it per se, just let the set screw self tap. As I said the tricky thing here is assembling it all, and one of those...
  20. Eric_F

    Best d.i.y. option for brass annealing.

    The Skip Design is what you're looking for. Here's my build list, it's a bit of a pain to fit it all together. I wouldn't use MDF again personally, and I could not get the proximity sensor working but I've seen other people with them working fine. Here's a link to skip himself:
Top Bottom
Back
Home
Forums
Merch
Alerts