Search results
-
Presses for PRS reloading
@Sheldon N thats disgustingly fast lol- OzzyO20
- Post #25
- Forum: Reloading Depot
-
Presses for PRS reloading
I use a Co-Ax, but it’s no faster than any other single stage press out there. I save time with a F&D Auto-trickler, Bench source annelaer, and soon to be Giraud case trimmer. The Dillon is interesting, and a buddy is starting down that path as we speak. I’ll keep and eye on his results and...- OzzyO20
- Post #23
- Forum: Reloading Depot
-
-
-
Gunsmithing Stupid Question Alert: Can I slide a reamer in a chamber?
I'll have to get a different bushing. I'm guessing a slit case isn't accurate enough for this?- OzzyO20
- Post #8
- Forum: The Armory
-
Gunsmithing Stupid Question Alert: Can I slide a reamer in a chamber?
@Mike_in_FL that's the thing, I have measured the OAL after seating .020" off the lands and the designer said should be in the 2.760 range. I'm closer to 2.580" OAL.- OzzyO20
- Post #3
- Forum: The Armory
-
Gunsmithing Stupid Question Alert: Can I slide a reamer in a chamber?
I know the tolerances are extremely tight, and this might not even be closer to possible. I think my chamber was cut with the wrong reamer (too little free bore is my guess) and I'm wanting to purchase the correct reamer anyhow. It'll be a good while before this barrel is shot out, but I was...- OzzyO20
- Thread
- Replies: 12
- Forum: The Armory
-
-
Accuracy International Picture Thread
Installed @samb300 ’s Arca Swiss spigot replacement today, along with a RRS BT-Pro clamp. Total install time was about 2 hours. That’s 10 minutes to remove the factory mount and install Sams, then 1 hour and 50 minutes hunting the 10-32x3/8 screws for the RRS clamp before giving up and going to...- OzzyO20
- Post #3,431
- Forum: Bolt Action Rifles
-
Graphite or wax for bullet seating?
I'll try the dryer sheet and mineral spirits. Just a cap full?- OzzyO20
- Post #39
- Forum: Reloading Depot
-
Graphite or wax for bullet seating?
I went down this road when I was considering having someone else anneal my brass. They wanted to wet tumble the brass beforehand, and I have heard negative input about 6.5 CM brass and steel media peening the necks. So I ended up just buying a Benchsource annealer and ordering a RCBS ultrasonic...- OzzyO20
- Post #33
- Forum: Reloading Depot
-
Rifle Scopes What is the Best Christmas Tree Style PRS Reticle?
I've cleaned a 400 through 1,000 stage at a match with a H59 with my PRS rifle, and hit an IPSC at 1,000 with a 308 and old school mildots. Point is, doesn't matter the reticle as they can all be 'made to work.' You need to find what works best for you. For me, that's the H59 at the moment.- OzzyO20
- Post #19
- Forum: Observation & Sighting Devices
-
Hornady or Lapua Brass for 6mm Creedmoor.
To add to Hollywood's reply, the general consensus is that SRP brass primer pockets last longer than LRP primer pockets.- OzzyO20
- Post #20
- Forum: Reloading Depot
-
-
Hornady or Lapua Brass for 6mm Creedmoor.
Lapua is always the answer.- OzzyO20
- Post #16
- Forum: Reloading Depot
-
-
Giraud Power Trimmer
This is the very first piece of gear I'm getting after I'm done renovating this money pit of a house.- OzzyO20
- Post #32
- Forum: Reloading Depot
-
-
-
