Search results
-
Gunsmithing Best epoxy for polymer composite chassis repair
You may want to look at this product.- B y r o n
- Post #2
- Forum: The Armory
-
Precision Rifle Gear 3d printing bore guide question
Have you considered turning one out of Delrin in a lathe? I think this is what a lot are made from.- B y r o n
- Post #2
- Forum: The Armory
-
Appropriate scope for a Remington 700P
You didn't mention what caliber you are working with. What are you trying to accomplish with your 700P?- B y r o n
- Post #6
- Forum: Observation & Sighting Devices
-
Cadex tripod vs. everything else
Here is what I went with. See post #37 & 38. The latest version is the S0-322CX.- B y r o n
- Post #6
- Forum: The Armory
-
-
Secret Service Wants New Rifles
I'm not aware of any rifle that is configurable as a left or right hand rifle. Correct me if I'm wrong.- B y r o n
- Post #12
- Forum: Bolt Action Rifles
-
Rings recs and lapping?
Lapping rings was common when receivers were questionable for consistency between front and rear and two piece bases were used. With good once piece bases or receivers with solid picatinny bases built in lapping was generally not needed. If it is a top tier ring/shop don't lap, if it is a...- B y r o n
- Post #16
- Forum: Observation & Sighting Devices
-
Garmin Xero $499 link in post
Botach is one of those places that is hit or miss. When I lived in California I could drive to their shop and I did try ordering from them on line. What I learned is that if ordered online it may never arrive and was better to actually go to the shop and lay my hands on what I wanted. They...- B y r o n
- Post #10
- Forum: The Armory
-
Does "Over-Annealing" Impact Shot Dynamics?
You didn't mention what method you used to anneal the brass. Here is my simple understanding of annealing - heat metal to appropriate temperature to anneal. If that temperature is not reached then the metal is not annealed. If temperature is to high than the metal can be taken to dead soft...- B y r o n
- Post #4
- Forum: Reloading Depot
-
-
New Rifle Build......need magazine recommendations.
You might want to look at post #32 in this thread.- B y r o n
- Post #11
- Forum: The Armory
-
No more bacon for you
They do test but don't recall frequency. When a deer tested positive just South of the state line in TN, they made mandatory check-in stations in counties nearby. They also prohibited baiting because it congregates deer which would make spreading easier. No deer where found to have CWD.- B y r o n
- Post #63
- Forum: The Armory
-
No more bacon for you
This is Kentucky's answer to the problem. 95% of land in Kentucky is privately owned. If you are a farmer or rancher would you want people you don't know to come onto your land. I've only lived here a relatively short time but think Kentucky Fish and Wildlife is doing a pretty good job. It...- B y r o n
- Post #48
- Forum: The Armory
-
Surgeon actions
"Strategic Armory Corps provides the sacfirearms.com and their subsidiary brands, Surgeon.com, awcsilencers.com, surgeonrifles.com, and Surgeonfirearms.com websites to you subject to the following conditions. If you visit, or purchase from any of the aforementioned websites, you accept these...- B y r o n
- Post #12
- Forum: Bolt Action Rifles
-
New scope
The only reason I can think of for doing this is if you are using the twist in front ring and windage adjustable screws for the rear mount. With the windage centered you would use the screws of the rear mount to get you centered on the target. Once you have that then use elevation adjustment...- B y r o n
- Post #7
- Forum: Observation & Sighting Devices
-
Scope ring identification.
Not Badger Ordnance and with no markings, no way to tell who made them.- B y r o n
- Post #5
- Forum: The Armory
-
Garmin Xero C1 Pro chronograph
Garmin it appears would rather not publicly document errors/enhancements or mistakes thus no change log of changes to the software. Like a lot of you, I like to know why something is being updated especially if it covers something I don't plan on using or needing as updates are opportunities...- B y r o n
- Post #2,704
- Forum: The Armory
-
200gr for 30cal loads
You might be better off with a bullet in the 175 gr range. Rifle twist in the 308 might not be up to heavier slugs. If they are then 220 gr may be better.- B y r o n
- Post #2
- Forum: Bolt Action Rifles
-
AICS magazine identification
If the magazine is hitting the bottom metal before the magazine latch will catch then your only recourse is to use longer magazines like 10 rounders. It's either that or change the bottom metal to a version that will allow the 5 rounder magazine to engage the catch when inserted.- B y r o n
- Post #6
- Forum: Bolt Action Rifles
-
M40a1 available at GAP
If this is what you are looking for than you won't find any better. I have an Eric Reid built SCLE and is a great rifle!- B y r o n
- Post #2
- Forum: Vintage Sniper Rifles
