• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Search results

Search the forum Search Articles
  1. 1

    6.5 CM Berger 130 Gr loads

    Found out the Hornady box for 130 ELDM said G7 of .279, but applied ballistics says .247. that explains my long range frustration.
  2. 1

    Recipe for Hornady 130 ELD Match 6.5 Creedmoor?

    130 eldm were very accurate for my jp barreled gas gun. 40 gr varget at 2850 from a 22inch tube in 95F temperature with Hornady brass. The bullets bc is not as good as the hybrid and eldm bc is also optimistic. After getting excited about my load at 600 yds I couldn't make contact at 800 and...
  3. 1

    6mm BR

    Accurate mag with the primal rights kit has the best chance of working. Whidden and Forster dies. Always get a micrometer seating die. 105 hybrid is all you need with a 6br. 30 gr varget WITH LAPUA BRASS and 0.020" jump. Expect 0.004" of wear per 100 rounds after the first 50 or 100 or so. But...
  4. 1

    7mm SAW

    I'm wondering if my Smith received a reamer for turning necks by accident. I ordered a barrel, brass, dies, and reamer from WTO at the same time. I may see if I can get Clayton. Hate to this close to Christmas
  5. 1

    7mm SAW

    MAJOR 7SAW CHAMBER TROUBLE HERE I built a saw with 2 barrels over summer and am using the holiday to finally break it in but I'm stuck. Reamer from WTO to my Smith. 500 alpha brass from WTO New neck is .312. With bullet seated is.313. I CAN'T EVEN GET NEW BRASS IN THE CHAMBER. I forced one with...
  6. 1

    Firearms 7 saw in 737 and ACC

    This is a complete rifle with 2 barrels, 500 alpha brass, dies, and 98 162 eldm
  7. 1

    Heavy barreled 7 mag or 6.5prc

    Who makes an economical 7 Magnum or 6.5 PRC rifle with a heavy barrel at least 24 in Long?
  8. 1

    Firearms 7 saw in 737 and ACC

    I have a complete 7 SAW rifle that I do not have time to do anything with (hot new girlfriend- very expensive), nor do I want to keep putting money into it. I have 2 barrels one I counted as free, both HV Varmint 27”. The weight is needed to keep the 7Saw from bucking off target during...
  9. 1

    7mm SAW

    I have been sitting on a complete rifle in 7 saw for months with no time to even fire it 737 r ACC 2 28" hv varmint barrels 1000 180hybrids 500 sorted alpha brass Dies Where would I go to sell it for say 90% cost?
  10. 1

    7mm SAW

    Oooops. 2700. Fixed it
  11. 1

    Any Masterpiece Arms rifle owners out there?

    Mine should be fixed. Pulled the barrel. Bore scope showed a massive carbon rim. Empty brass would get stuck in the chamber. Cut .020" off same case and it slipped in and out. It took C4 and a brush in a drill to get it out. Bore scope shows no ring or rim. Brass doesn't get stuck. Still have...
  12. 1

    Impact Precision Actions

    I just put together an impact with a razor 2 on top. The bolt knob is very close to the scope. Is there anything I can do or should I just run it until I get used to it. Tenebrex scope caps BTW.
  13. 1

    7mm SAW

    I'm planning to shoot the 180hybrids well over 2700fps in the short chamber with alpha brass and 28" barrel. I have varget and h4350. Should I just order some reloader 16 or try what I have?
  14. 1

    Impact Precision Actions

    My bolt knob is barely missing my Razor gen 2. Of course I had an axiom before this that cleared by a mile
  15. 1

    7mm SAW

    Alpha seems to be nearly as consistent as lapua in weight. For sure the alpha necks are more round. 170.3-5 170.5-2 170.7-2 170.8-2 170.9-1 171-3 171.1-7 171.2-66 171.3-108 171.4-104 171.5-79 171.6-41 171.7-32 171.8-24 171.9-20 172-3 172.1-1
  16. 1

    Area 419 Arcalock clamp, and MDT ACC dovetail

    Does that mean they will swap any clamp that is loose on an MPA chassis?
  17. 1

    Area 419 Arcalock clamp, and MDT ACC dovetail

    My 419 clamp needs the pins in to clamp an MPA rail and spigot. It eats the chassis up pretty fast but holds. If 419 would give the clamp just a little more travel we would not need the finish scarring pins.
  18. 1

    Impact Precision Actions

    Is there a place to get an AW cut Impact without a long wait? Can the cut be added later and still be as reliable as the factory cut?
  19. 1

    6mm Dasher

    Cfe223 is very temp sensitive. I am more interested in TAC or ar comp since 8208xbr peters out
  20. 1

    Berger 185gr Juggernauts

    Would it be safe to order a barrel throated long and plan on jumping the juggernaut 0.100" ish from a magazine? I would never single feed. Would hate to order it but then not get it shooting because of the jump.
Top Bottom
Back
Home
Forums
Merch
Alerts