• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Search results

Search the forum Search Articles
  1. jLorenzo

    MK 12 Mod 1

    White Oak makes SPR barrel as well.
  2. jLorenzo

    What did you do in the reloading room today?

    Trimmed some Lapua 223. I love this thing. No regrets, would buy again. Almost stopped reloading because of how much I hated trimming the old way. Cut my time way, way down. Better end result also.
  3. jLorenzo

    .308 Winchester

    https://www.m14forum.com/threads/m852-special-match.472674/ Lengthy detailed post about all that stufd I found while digging around.
  4. jLorenzo

    .308 Winchester

    Whats up with these markings on the side? This is old LC match.
  5. jLorenzo

    .223 - 5.56

    Get 100 and see what you can do. I had a gun with a Bartlien shoot 55gr winchester xm195 really well.
  6. jLorenzo

    .223 - 5.56

    Best currently available powder choice for 62gr loads in gas guns? Preferably ball to use in a thrower. Would like to get some accuracy tuned in if possible.
  7. jLorenzo

    AR 10 light primer strike

    Say I didnt bump the shoulder enough and some of the rounds had a tiny bit of excessive headspace keeping the bolt from going all the way into battery, would this keep the firing pin from striking?
  8. jLorenzo

    308 Winchester AR Only

    How would you guys size once fired LC bought online? Decap and check shoulder measurement compared to brass fired in your gun?
  9. jLorenzo

    AR 10 light primer strike

    JP says not to use their pin with anyone elses bolt. Ideally Id like to have a matched bolt and barrel down the road. Is that measurement how much the pin protrudes from the bolt?
  10. jLorenzo

    308 AR10 Build Info/Picture Thread

    How do you like that scope?
  11. jLorenzo

    AR 10 light primer strike

  12. jLorenzo

    AR 10 light primer strike

    So do you think its the case web keeping it from fully chambering?
  13. jLorenzo

    AR 10 light primer strike

    I have not as finding the actual length spec on a firing pin when buying doesn't seem to be possible so essentially I would have to keep buying them and hope for the best without knowing if the new pin is any longer than the one I have.
  14. jLorenzo

    AR 10 light primer strike

    The primer looks the same as if I had just chambered the round and ejected it. Keep in mind 90% of the rounds fire and function fine.
  15. jLorenzo

    AR 10 light primer strike

    Maybe I need to use a small base die? I have one with a broker decapping pin. I think I could swap a new pin over to it. Both dies are RCBS.
  16. jLorenzo

    AR 10 light primer strike

    I may have had to tug a bit to get them to eject. If its being over sized why would the shoulder be in the same spot when comparing fired vs. Sized brass? I decap before measuring. Speaking on the die, sizing for another caliber to bump the shoulder 2-3 thou the shell hold does not touch the...
  17. jLorenzo

    AR 10 light primer strike

    I am not able to bump the shoulder on fired brass even with the shell holder touching the die.
  18. jLorenzo

    .308 FTW

    He was talking about holding under at 35y for his 22, didn't mention his zero distance. Maybe he mispoke. Zeroing at 100 and shooting under 60y or so you would be holding over or dialing up. So you would be correct.
  19. jLorenzo

    .308 FTW

    Whats his hold in mils taking into account height over bore at say 10y, assuming 2.5" height over bore?
  20. jLorenzo

    .308 FTW

    Assuming you don't have a zero stop set. Another thing to keep in mind.
View older results
Top Bottom
Back
Home
Forums
Merch
Alerts