• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Search results

Search the forum Search Articles
  1. M

    2000MR+308+155 SMK Palma OCW test part Deux

    Good shooting! Says it all.
  2. M

    OMG, my primers!

    Pin spring might be a little weak...
  3. M

    SCORED!!!! IMR 4064 Need primer suggestions.

    4064 doesn't need any special primer to work well. Any CCI or Federal, or REM primer, as long as you work up the loads and don't change primers in the middle of the work up.
  4. M

    .223 hand load suggestions for 1/9 bolt rifle ??? HELP

    http://www.snipershide.com/shooting/snipers-hide-reloading/108348-223-remington-tactical-owners.html
  5. M

    Solvent to remove Imperial Sizing Die Wax

    Mineral spirits, naphtha, denatured alcohol, others as mentioned above. I usually wash mine with hot water and a little simple green.
  6. M

    Alliant AR-COMP...anyone use it for .223/5.56?

    It works great under a 75gr bullet, I like it!
  7. M

    2000MR + 308 + 155 SMK Palma OCW test

    Could you tell us a little more about your cases and prep? Good shooting btw.. edit: I see now on your target that you are using virgin Lapua brass, so there probably wasn't much case prep.
  8. M

    2000MR + 308 + 155 SMK Palma OCW test

    Was this 2155's or 2156's
  9. M

    Accurate scale?

    I sent mine back, it didn't weigh the same thing the same weight more than once,slow to react to trickling, by the time it reacted, the charge was over. In my opinion, hundredths of a grain is almost TOO fine a resolution, I don't need something that weighs fingerprints. Mainly, it was the...
  10. M

    Does hail effect the bullet?

    I would like to see that...
  11. M

    Alliant 2000mr in the ar15 - impressed

    Thanks, much appreciated.
  12. M

    Blowing primers at MINIMUM load?

    This!!
  13. M

    HELP: Starting to load for my M1A

    Yes, it will! The main thing with the M1a is port pressure, 12-14000 psi is the operating range. Uniforming the primer pockets is something I just do for ALL of my gas guns. The Schuster plug is great if you want to load bullets over 175-178gr. I adjust mine from closed, to open enough to just...
  14. M

    Blowing primers at MINIMUM load?

    Seems to be a lot of Win primers blowing on the radius.
  15. M

    Question on trimming 308 brass

    Not enough to measure with a caliper, by the way, .006 is a mile as far as heat expansion is concerned.
  16. M

    Central florida - reloaders

    So,,,what next??
  17. M

    And Yet Another Shoulder Bump Question

    Just zero it on an average of 10 fired cases if you don't know your chamber's actual dimensions. Or use bigedp51's method above.
  18. M

    And Yet Another Shoulder Bump Question

    Bear in mind that the Hornady tool is just a comparator. bigedp51 uses a headspace guage to set his up, that stupid little bevel that Hornady puts on it messes up the linear measurements.
  19. M

    Lot to lot variation on Alliant PP2000MR

    It really shouldn't make a difference, maybe if you left the lid off and out in the sun...
  20. M

    powder funnels

    I find Saturn funnels heavy, clumsy, and expensive. I have a Lyman that I have been using for many years.
View older results
Top Bottom
Back
Home
Forums
Merch
Alerts