• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Search results

Search the forum Search Articles
  1. insight3b

    Gunsmithing Rem 700 SPS .300 WM issues...

    Original stock with original screws?
  2. insight3b

    5.56 brass any good for 223

    Its all I use but you do have to remove the primer crimp
  3. insight3b

    sticky bolt on .308 loads

    You can use the chamfer end of a chafer/deburr tool
  4. insight3b

    sticky bolt on .308 loads

    Remove the front guard screw completey and try chambering. Sounds to me like the front screw is too long
  5. insight3b

    RCBS Customer Service

    You better marry that girl...women like her don't come along often
  6. insight3b

    Lots of weight to lose

    Along with diet of course comes excercise and I hate going to the gym. Gotta get in the car or run/bike to the gym so I decided to just work out with what I always have with me...just my body weight. I do push-ups during commercial breaks of programs I'm watching and two hundred before every...
  7. insight3b

    sticky bolt on .308 loads

    Original stock with original action screws?
  8. insight3b

    Lots of blemished bullets and brass in-stock

    30 cal 168gr AMAX are back: Blemished Match Bullets 30 Cal (308 Diameter) 168 Grain Polymer Tip
  9. insight3b

    RCBS Customer Service

    They are awesome. One thing that helps to actually lock he locking screw is to mash a piece of #6 or smaller bird shot into the threads. Bird shot first then the screw...the lead from the shot gets mashed into the thread by the screw and actually locks the nut
  10. insight3b

    M14 closes on a 308 no go gauge- sell it or keep it?

    Easiest fix would be to try a new bolt...hardest would be to rebarrel. Not much you can do with handlaods to fix it
  11. insight3b

    Gunsmithing Check out this brand new Remington 700's recoil lug

    Its such an easy fix and easier to prevent during initial assembly...no reason for it
  12. insight3b

    Winchester 308 brass reload problem

    Easy fix...go back to LC brass. You should get more speed with less powder in LC brass too due to its thicker construction and reduced case capacity
  13. insight3b

    redding full length die "losing" not braking decapping pin on Dillon 550 ideas

    The decapping pins are probably stuck inside the primer/flash hole of the case you tried to decap. There are two types of decapping pins headed and head-less. Sounds like you need the headed variety but are using the head-less. The headed pins look like a small non threaded screw and non-headed...
  14. insight3b

    Disposing of bad ammo?

    During the great flood here in TN were told we could take it to local PD for proper disposal. We were told not to throw it in the trash because most of our trash goes to an incenerator
  15. insight3b

    Lots of blemished bullets and brass in-stock

    6.5cal 140gr polymer boat tail Match...look like AMax to me: Blemished Match Bullets 264 Cal 6.5mm (264 Diameter) 140 Grain Polymer
  16. insight3b

    Lots of blemished bullets and brass in-stock

    .30 cal 168gr polymer tip...look like A-Max to me: Blemished Match Bullets 30 Cal (308 Diameter) 168 Grain Polymer Tip
  17. insight3b

    Lots of blemished bullets and brass in-stock

    178gr .308 Match HPBT: Blemished Match Bullets 22 Cal (224 Diameter) 75 Grain Hollow Point
  18. insight3b

    Lots of blemished bullets and brass in-stock

    75gr .224 Match HPBT look like Hornady to me: Blemished Match Bullets 22 Cal (224 Diameter) 75 Grain Hollow Point
  19. insight3b

    Powder tracks on case neck?

    No those aren't light loads in my opinion
  20. insight3b

    Powder tracks on case neck?

    I only get those marks when I fire a load with a light/starting powder charge
Top Bottom
Back
Home
Forums
Merch
Alerts