• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Search results

Search the forum Search Articles
  1. S

    Reloading press advise

    Make it simple. Progressive reloading, make it a Dillon. Single stage, make it a redding
  2. S

    Redding neck die .338 Lapua

    That is brass build up inside your die, in the neck area. Clean it up as you would a rifle chamber and you will see the scratches will go away
  3. S

    Gunsmithing Best release agent for bedding?

    Best stuff out there is the acra aerosol release from brownells imo
  4. S

    Gunsmithing DPMS 6.5 creedmoor Barrel with off center chamber?

    A bore scope would give you a better view. Do you have access to one?
  5. S

    Gunsmithing Did I just buy a new stock?

    No need for a dremel. That stuff will come off w a razor knife and a scraper. I usually go all the way to the bottom. On the front i go to where theres solid fill. To the rear about an inch. The recoil pads are glued on btw. Also rough up the inside after you have it hollowed out so your new...
  6. S

    Gunsmithing Did I just buy a new stock?

    Proneshooter-that stuff has to be completely removed and replaced with solid material. I use bondo short strand filler and marinetex to get a solid foundation for the base to adhere to. Once cured, you can mill a slot for the base and glue it in. You would have to do the same to the top as well...
  7. S

    Gunsmithing PTG Bolt Problem

    Bet you ten bucks they lost the thing and are just putting you off while they try and find it!
  8. S

    Gunsmithing Stockdoc

    Thank you sir. Enjoy
  9. S

    Gunsmithing After market adjustable cheek piece by Joe Ducos

    Hondo and Dave pm's answered Sentry- works the same way as with fiberglass stocks. No problems at all
  10. S

    7mm RM... Marginally or significantly more capable then .260?

    I have used the surefire two baffle short brake and it works really well. The jp brake also works, but as previously mentioned, it isnt very aesthetically pleasing.
  11. S

    7mm RM... Marginally or significantly more capable then .260?

    There are a lot of very effective muzzle breaks in the market right now. Im sure there is one out there suitable to your application wether 7 or 300 mag. Recoil will not be an issue
  12. S

    Seekins Bottom Metal

    If installed at the correct depth they work great. Imo the mags are not as good as ai, but then again they dont cost as much either
  13. S

    Gunsmithing After market adjustable cheek piece by Joe Ducos

    19scout- can do. But you would need a repaint if its a cammo job.
  14. S

    Gunsmithing After market adjustable cheek piece by Joe Ducos

    Requiem, that looks very nice assembled. Good job!!
  15. S

    .22-250? Any one shoot it?

    Stranded-I had tried 38 gr of h380 but it was way hot in my gun. 36.5 was a safe load under all the weather extremes I shoot under. It gave me 3765ish fps through my 26" factory stainless tube. I got those velocities by shooting over my chrony 2 chronograph. Hope that helps
  16. S

    Gunsmithing After market adjustable cheek piece by Joe Ducos

    Rbdub474 your stock is almost done. I will have it back to Marcs by this weekend
  17. S

    Funniest Youtube video yet..!!!

    Takes all kinds! Wow
  18. S

    How hot is too hot?

    What were the environmental conditions you shot those at? Primer flattening is not a very reliable indicator of pressure. By the time you notice flattening you may be way over on the pressure If you shot that group at cooler temps you might get in trouble with that load in the heat
  19. S

    Gunsmithing AR-15 Stripped Lower Assembly - What Gives?

    Maybe somehow a Colt large front pin got in that lpk bag.
  20. S

    frustrated, gunsmithing, reloading, OAL hunt in one week. Bolt gun.

    Just remove that metal piece on the rear of your mag box. I have done the same thing to a couple of win 70 rifles and have had no problems. Just make sure that the bolt will retract enough to pick up a round. If it doesnt you will have to shorten the bolt stop the proper amount as well. Good luck
Top Bottom
Back
Home
Forums
Merch
Alerts