• New Contest Starting Now! This Target Haunts Me

    Tell us about the one that got away, the flier that ruined your group, the zero that drifted, the shot you still see when you close your eyes. Winner will receive a free scope!

    Join contest

Search results

Search the forum Search Articles
  1. P

    Whidden die hard to thread into RCBS Rebel

    Mine did the same thing in my Mec Marksman. Screwed it in and out several times and it was fine.
  2. P

    Small Base Dies(Body vs Full length)

    I use a redding body die to bump the shoulders back then use a lee collet die to size the necks. If you use a body die you will have to size your necks with something.
  3. P

    6.5 Creedmoor Dies

    PM sent to the op.
  4. P

    Initial experience loading for 6.5prc bartlein carbon barrel. Inconsistent when cold.

    Going to keep an eye on this as I have one sitting in the safe. What contour is the barrel?
  5. P

    Reloading Equipment WTB 6.5 Creedmoor dies

    I have a redding micrometer seater I would part with.
  6. P

    Brass Prep... A waste of time?

    Or a "Lee privileged" meme.
  7. P

    Single Stage Press Recommendations

    MEC Marksman. Not as popular as some of the others but a great press. Smoothest I've used.
  8. P

    Best electronic powder scale out there?

    A&D FX 120i.
  9. P

    Just got my first progressive

    Check out YouTube for some tips and tricks. Most of them are worth doing.
  10. P

    Sheared Case Neck Off While Neck Sizing.

    I use a Lee collet die for my 6.5 creed and never use lube. These dies shouldn't open up the neck. They should squeeze it smaller. Did you full length size, body size, or were you neck sizing fire formed brass?
  11. P

    New reloader hornady LNL AP

    I don't see the need for a separate measure for each caliber. I already had one when I got my AP. I use them for quick powder changes for different loads during a loading session. They are easy to adjust. The micrometer makes it quicker because you have reference marks when making adjustments. I...
  12. P

    New reloader hornady LNL AP

    It took me a while to get my powder measures (2) set up, but once done, they drop within 0.1grain very consistently. I do only use them for pistol and 300 blk. Get the appropriated micrometer metering assembly and it is much easier to make adjustments. Right now, the price of shell plates...
  13. P

    Cold Welded Bullets in Neck

    I tried it. With smaller bullets (308,264) it's hard to keep it on the bullet ond off your fingers.
  14. P

    Carbon ring removal

    Two 20 minute soaks with clr on felt pellets removes the carbon rings out of my 6.5 cm's. After that I flush the chamber with bore blaster then oiled patches in the chamber and bore.
  15. P

    Chargemaster lite opinions

    Use mine to throw charges and fine tune on an fx 120i. If it broke I'd get another one today (assuming I could find one).
  16. P

    Firing 308 win with only a primer

    Buy an extra rod and remove the decapping pin. Next time something like this happens (and it will) you can resize without depriming. Did this with my lee collet dies.
  17. P

    Berger 6.5cm 140g hybrid

    Try Bullet Central. Git mine last week. They took a long trip around the country with UPS but I finally got them. Looking forward to some good weather to test them.
  18. P

    Bushing vs. Expander Mandrel For Obtaining Neck Tension

    Spife, thanks for the info.
  19. P

    Bushing vs. Expander Mandrel For Obtaining Neck Tension

    What are you using to measure the seating force?
  20. P

    Brass prep after pulling bullet on a loaded round

    I resize the neck then reload. Never noticed a problem when I've had to do it.
Top Bottom
Back
Home
Forums
Merch
Alerts