Search results

Search the forum Search Articles
  1. B

    Compressed Loads

    Well????? buying new brass is up to you to decide??? LOL Hope that helps!! HAHA!! It comes down to how much PPU you have, and volume of rounds you would need, for use of whatever the rifle is for. Got a few spair $$$ to spend for good brass? Its a Performance/Qty/Cost point. I...
  2. B

    Can/should I remove primers and start over?

    Here is an OLD thread on 300WM and primers, May or may not be of Help. https://www.snipershide.com/shooting/threads/cci-br2s-in-a-300-win-mag-no-go.167786/
  3. B

    Compressed Loads

    Use of a drop tube will help for sure, I personally do not like super compressed loads, I stop and back up a bit as soon as i see my seating depth change. May research some on case volumes, PPU might be significantly less then another brand. Hornady or Winchester. Try a slightly faster...
  4. B

    Users of Hornady case length gauge, didn't the bullet pusher used to be made of brass?

    Had mine for many years, its plastic. No issues. I guess if you want you could replace it with a aluminum or brass rod if you like.
  5. B

    Can/should I remove primers and start over?

    What is the rifle going to be used for? Hunting in cold weather? Personally i stick to mag primers in mag cartridges. Hard for me to say what the change will be by switching primers, Really should restart low and work up with any component change. Depends on how hot your already pushing...
  6. B

    IMR 4955 Enduron. The good, bad, and ugly?

    Midsouth has SW4350 in stock, Not sure how it will do with the 300WM, but should be OK in the 6.5?
  7. B

    Roll Sizing in Middle Tennessee

    I assume the ammo fired from your pistol is bugling the brass to the point you equipment will not take the bulge out? What is your load info? Powder charge, Coal and bullet wight? What Kind of pistol? For the last 20 years i have used only range pickup brass, Never had to roll size any...
  8. B

    People don’t want to go back to work?

    I was under the impression that if you were offered your job back after being layed off, and you did not take it, then you likely would loose your UI benefits.
  9. B

    Ammo Shortage 44 SPC/44 Mag projectiles from 40 S&W fired cases.

    good stuff. I have the cobin set to make .224 projectiles out of 22 cases.
  10. B

    What are reasonable velocities out of a 22" .260 Rem Gasser?

    I found running a heavy carrier with a tubbs wight, and adjustable gas was key in my 24 inch gasser. (kreiger Barrel) Kept locked longer, Running a 140 Tipped nosler CC at 2700 with no pressure, Also have a 18 inch Proof CF gasser for hunting, running a 143 eldx at 2600ish. Lupua brass with...
  11. B

    Reloading Equipment Tite group in stock

    8lbs of Tac in stock right now.
  12. B

    Concerns with 300WM load

    Might want to check pockets now to make sure your not toasting them, and keep toasting them........
  13. B

    decapping live primers?

    I just deprimed about 350-375 223 brass with live primers, It was all junk ammo, bad cases, Odds and ends ammo picked up at matches and shooting ranges over the last 12-15 years. Pulled bullets and dumped powder, then loaded up in the 650 with a lee decapping die and went to town, I did sneak...
  14. B

    Brass Sticks in Chamber With Low Pressure Loads - Help Please

    May want to do an internal volume check, and compare to other HS brass. Im assuming a 308?
  15. B

    Wrinkled Case?

    Wow you did not notice that while, priming, powderen it, or seating a bullet? What kind of ammo inspection do you do after loading?
  16. B

    Reloading Equipment Powder Valley

    https://www.midsouthshooterssupply.com/item/00034staball1/winchester-staball-6half-smokeless-powder-1-lb
  17. B

    Hodgddgdon's reloading center

    probably all messed up on the server side from 600,000 people a day trying to figure out load data for some BS powder they have never bought for some caliber its not good for...... I just got 16 lbs of JENKY X POWERSHOCK cause thats all that was for sale, Anyone load this powder in 9mm, 6.5 PRC...
  18. B

    I won the reloading lottery today......

    o man, you will be in Debt to him for a long time to come..... That looks like a lot of favors to me...... NICE!!!!!
  19. B

    Hodgddgdon's reloading center

    Just check and all 3 of those show up on my drop down menu.
  20. B

    Ammo supply improving in my area (SC)

    so 1 store that finally got its back ordered ammo in from 14 months ago means we are getting the supply back??? uhhh no....LOL
Top Bottom
Back
Home
Forums
Merch
Alerts