• Quick Shot Challenge: What’s the most underrated gear you never leave home without?

    Contest ends Wednesday, join now for the chance to win free Hide merch!

    Join contest

Search results

Search the forum Search Articles
  1. FLIGHT762

    Shoulder Bump Problem!

    The die that you need space between the shell holder and die is the seating die, if you don't want a crimp. If you set the seating die too low, you can buckle the case shoulder, which will cause chambering issues.
  2. FLIGHT762

    Precision reloading for an M1 Garand…anyone experimented enough to find a 1 MOA load? Is it even possible with a Garand?

    The 173 Gr. bullet was the old M-72 FMJ Match bullet.
  3. FLIGHT762

    308 / 7.62x51 reloading

    The same reason you don't find 5.56 NATO dies. No difference in 223 Rem. / 5.56 NATO or 7.62 NATO & 308 Win. dies. The outside diameters of the brass are the same.
  4. FLIGHT762

    Biggest unicorn

    Nobody wrote Federal 215M's. So, there it is.
  5. FLIGHT762

    308 Winchester AR Only

    My point of not buying RE-15 again is related with it's poor temperature sensitivity. I had good luck with it. I have a couple of #'s left and I'll use it up. RE-15 is just as expensive to buy as other powders like Varget, H-4895, 8208 XBR, & AR Comp which are much less temperature sensitive...
  6. FLIGHT762

    308 Winchester AR Only

    I've used a fair amount of Re-15 in the 308. I will NEVER buy it again. I've tested 8208, AR Comp, H-4895 and Varget in my 4 308's, 2 gas guns and 2 bolt guns. Any of those are my preferred powder in the 308 with 155's, 168's and 175-8's. Re-15 is temp sensitive enough for me in my climate...
  7. FLIGHT762

    Whose 308 ammo to purchase

    Newer Federal Brass with the blue primer sealant is decent brass. The very old federal brass was soft. If you're getting loose primer pockets on the newer brass after one firing, your loads are too hot.
  8. FLIGHT762

    Whose 308 ammo to purchase

    Stay away from the recently made Turkish made ZSR M-80 ball ammo, it's been blowing up guns.
  9. FLIGHT762

    308 Winchester AR Only

    That is not M118 load data card. It is the newer, Navy Mk 316 MOD 0 using IMR 4064. The DODIC- AB39 is for that ammo. M118 was loaded with a couple of different powders over the years. The older M118 L/R load loaded with Reloader 15 and had pressure issues in the Desert. The DODIC for that load...
  10. FLIGHT762

    Shoulder bump inconsistency

    I'll explain it this way, I have two of the Hornady .400 inserts. One is very old, the other one was purchase a couple of years ago. I have a friend with a 1.630" GO gauge for 308 Win. and he let me borrow it. I measured the GO gauge with both of the .400 inserts. The old insert measured...
  11. FLIGHT762

    Which shoulder bump/headspace gauges (other than SAC) index off the entire shoulder rather than a datum line?

    Sinclair inserts have a shoulder. It is a comparator and does not give SAAMI numbers. On a 1.630" GO gauge, my Sinclair 308 Win. insert measures @ 1.561". If you are looking for a SAAMI number, the RCBS precision mic and Whidden gauge are zeroed @ 1.630". what is the measurement off of the...
  12. FLIGHT762

    Reloading for 223/556 Service Rifle Competition (NRA/CMP bullseye)

    The "Magnum" primers, CCI 450, CCI 41, CCI BR-4 and Remington 7-1/2 primers all have a .025" thick primer cup. Most other small rifle primers have a .020" primer cup. The extra .005" thickness handles higher pressures better. *EDIT* spife beat me to it while I was typing.
  13. FLIGHT762

    Help Needed - Sticky Bolt CLOSE

    I've used it in my 22" GAP 10 with 175's in IMI brass. Brass didn't get beat up. I do have a Tubbs flat wire spring in it and have his CWS if i need it. I agree it's a slower powder for gas guns. I wouldn't use it in my M1-A's or Garands. Too slow for them.
  14. FLIGHT762

    308 Brass Primer Pockets

    ^^ Yup, that is it. ^^, that's the "something else going on". I had to go back and zoom in on the case photos and on the second case I can now see the pocket is convex from something pushing down from inside. supercorndogs caught it. I'd take the decapping rod out of the die and check to see...
  15. FLIGHT762

    Shoulder bump inconsistency

    O/P, you are NOT going to get a SAAMI headspace reading off of your Hornady Comparator. It is a Comparator, NOT a headspace gauge. New reloaders think you'll get SAAMI numbers off of the comparator, you do not. Just use the numbers you get off of you fired brass and set the die to bump minus...
  16. FLIGHT762

    308 Brass Primer Pockets

    I've been shooting Federal 308 brass since the 1970's. It has varied in weights over the years and the old brass was quite soft. Having said that, I've NEVER had FC 308 brass not accept a L/R primer. I've used every brand of primers including the Wolf Russian primers that are a bit bigger than...
  17. FLIGHT762

    90's primers price and reliability

    You can see what they paid for them years ago. I would offer them twice that. That would be more than fair due to the age of the primers. You both win.
  18. FLIGHT762

    Help Needed - Sticky Bolt CLOSE

    Since a couple others chimed in on other powders, I'll add this. Alliant 2000MR will get higher, safe, velocities in the 308. I've experimented with it in two of my 308's. I've gotten 2750+ FPS out of a 24" using 46.5 grs. in Federal GMM brass with no pressures with a 175 Nosler CC. Downside is...
  19. FLIGHT762

    Help Needed - Sticky Bolt CLOSE

    Cases look fine. The newer Federal GMM cases with the blue primer lacquer sealant is better brass than the much older GMM brass that had no primer sealant. I've shot it all. The old stuff is pretty soft.
  20. FLIGHT762

    Help Needed - Sticky Bolt CLOSE

    You are getting nowhere the lands @ max magazine length with a stock Remington barrel. They have long throats.
Top Bottom
Back
Home
Forums
Merch
Alerts