Search results
-
-
How long should a FL resizing die last?
I would guess the brass is the problem. Do you have some new brass you could try an experiment?- ShtrRdy
- Post #6
- Forum: Reloading Depot
-
Mag Release Fitting
I don't know the answer but I have a couple thoughts: - since the typical Mag catch angles up, if you shorten the tip it makes it protrude into the magwell less. - it could be possible that the mag catch is barely engaging the tab on the magazine. What is causing the magazine to not go in far...- ShtrRdy
- Post #2
- Forum: Bolt Action Rifles
-
Zermatt origin action trigger install
I've installed a few Trigger Techs and just followed the instructions. Each went well.- ShtrRdy
- Post #5
- Forum: Bolt Action Rifles
-
SOLD Special Order Foundation Centurion - Impact 737 Stock
Never mind.- ShtrRdy
- Post #4
- Forum: Buy - Sell - Trade
-
How did it go for you - barreled actions in your new chassis
You shouldn't have any trouble.- ShtrRdy
- Post #9
- Forum: Bolt Action Rifles
-
-
Tikka 260 Rem - First 9 Shots With Different Charge Weights Have Flyers
Humm, I don't know if this would apply then, ....... but a couple months ago I was having the same thing happen to me when firing a 223 bolt gun. I would load three or four cartridges into the magazine first. At this point I'm thinking it was something I was doing with the bipod or shoulder...- ShtrRdy
- Post #4
- Forum: Reloading Depot
-
Tikka 260 Rem - First 9 Shots With Different Charge Weights Have Flyers
I didn't go through the full data set but are you shooting the three rounds from the magazine or feeding them one at a time?- ShtrRdy
- Post #2
- Forum: Reloading Depot
-
AT-XC bolts are not compatible with AT/AW bolts
Would you mind pointing us to which post out of the 524 posts describes the changes? I spent some time looking through them but couldn't find any description,- ShtrRdy
- Post #13
- Forum: Bolt Action Rifles
-
AT-XC bolts are not compatible with AT/AW bolts
Would you mind providing a link which describes the design differences between the AT-XC and earlier short action AI's? I did a search and couldn't find anything about design differences. Just a lot of opinions on bolt lift feel.- ShtrRdy
- Post #7
- Forum: Bolt Action Rifles
-
Donor rifle opinions
Man, if it shoots well I would leave it alone and get another donor. But then it was probably hard to find a serial number that is similar to the M40 you're trying to replicate.- ShtrRdy
- Post #6
- Forum: Bolt Action Rifles
-
Reloading Equipment FTF in Columbia, Missouri: H4350, H1000, Fed 205M, CCI #200
Dang, I wish I lived closer to Columbia, MO! I-70 is close to me. But then I'd need to drive about 800 miles.- ShtrRdy
- Post #4
- Forum: Buy - Sell - Trade
-
Thoughts on the Aero Precision SOLUS ?
@FuhQ -- what chassis are you using? Looks like a nice rig. Please let us know how well she shoots.- ShtrRdy
- Post #590
- Forum: Bolt Action Rifles
-
-
Reloading Equipment Powder, BR2S in AL
I looked into this and for my area there are still Customer Centers but not as many as there once was. OP - if you haven't already go to the UPS website and see if their Customer Care Cente locator has one located near you.- ShtrRdy
- Post #18
- Forum: Buy - Sell - Trade
-
Reloading Equipment Powder, BR2S in AL
If you would be willing to ship ammo let us know.- ShtrRdy
- Post #12
- Forum: Buy - Sell - Trade
-
Weird primer strikes?
Have you taken a close look at the tip of the firing pin? Is the rifle easy to cock after firing? Wondering if it has a light firing pin spring? I've seen primers like that from semi-auto pistols. In that case it was because the hammer bounced or the hammer didn't have much pressure on the...- ShtrRdy
- Post #2
- Forum: Reloading Depot
-
Brand new rifle stuck casings
It kinda sounds like the primary extraction timing is off.- ShtrRdy
- Post #10
- Forum: Bolt Action Rifles
-
Barrel rifling
As another piece of information, the short range, (100, 200, 300 yards), benchrest folks use a 4-grove 6mm barrel- ShtrRdy
- Post #13
- Forum: Bolt Action Rifles
