Search results

Search the forum Search Articles
  1. D

    Do I need a small base die to save my brass? 6.5CM

    Another trick is to get a small base die in 260 or 270 for cheap so that it just sizes the base and nothing else. After you run it through a cheap ass small base 260 or 270 size the brass using the normal die.
  2. D

    308 brass over sized

    Damn was the guy trying to make another caliber out of 308 brass? I wouldn’t use it but that is just me.
  3. D

    308 brass over sized

    2 tenths and 2 thousandths is a huge difference. Is it .2 or .02 or .002?
  4. D

    Annealing issue

    Curious as to why the tanks need to be below the burner? I have mine on the side of the burner on the table standing straight up.
  5. D

    2 heavy bolt lifts and dirty cases

    try reshooting those cases, maybe it’s just isolated to those pieces of brass or shoot that load again. I never had luck with Starline, primers pockets were jacked up with a raised section around the primer hole and they said that’s normal. I had to cut out so much brass from just the center of...
  6. D

    2 heavy bolt lifts and dirty cases

    It normally happens on lower charges. I do love the exotic lighting on the pictures.
  7. D

    Terminus Actions

    Yup, ok here goes. I insert the firing pin into a block of wood or a hole in a wooden table. Depress the firing pin by pushing the bolt shroud down and remove the small screw on the under side of the bolt shroud. Entire unit comes apart. Keep depressing the bolt into the block of wood, once that...
  8. D

    Are Whidden Dies Worth It?

    Whidden dies do not over size the brass vs rcbs or Redding which sizes the cases almost back to factory. Whidden does size the base a tad smaller than most dies just not to the extent of being a small base die. Quality is worth the $.
  9. D

    tight chamber?

    Call the smith and let them know the virgin brass is a hard extract. Maybe their reamer is a bit small from many uses which is causing a tight chamber.
  10. D

    SOLD Nightforce Xtreme Ultralight A108 1.265” Intermediate 30mm Rings

    @Schmo Are these still available?
  11. D

    Official MDT 6BR Magazine Thread

    Anyone have issues feeding the 6br? If I cycle at a slower speed the round nose dives if I cycle fast and hard it feeds correctly.
  12. D

    Trigger tech tikka trigger info?

    Supposedly TT was working on a Tikka model for months now.
  13. D

    Annealing machine.........

    Technology is moving so fast things get outdated or changed and always something better comes out after you make a purchase. F@@k me…
  14. D

    Annealing machine.........

    I keep hearing in the videos that they changed the amp to a touch screen so it’s easier to replace, does that mean the screen or the buttons on the gen 2 breaks often? At some point they will stop making parts for the gen 2 as it costs too much to make parts for older models like any other mfgs.
  15. D

    MoneyPitArms Matrix Thumb Wheel ball and spring

    Take the cheek riser off and you see a set screw. Remove that set screw and turn the chassis over to let the spring fall out. Put a while towel or shirt down so you can see the spring when it falls out. Slide the wheel out and the detent ball will drop out with it. To replace it put the wheel in...
  16. D

    Mpa cheek riser 3d printed

    Anyone makes a cheek riser that is just the length of the cut under the cheek riser on matrix chassis? Similar to this. MPA won’t just sell this piece.
  17. D

    Am I being an idiot - Why am I getting pressure signs here?

    17:40 mark is your chamber too smooth to grab the brass causing bolt thrust?
  18. D

    Am I being an idiot - Why am I getting pressure signs here?

    He talks about base and what is considered a hot load.
  19. D

    Am I being an idiot - Why am I getting pressure signs here?

    After Seems to be the carbon build up if after 50 rounds the pressure appears. Scope the chamber after 50 rounds to see if there is significant carbon build up in the throat.
  20. D

    Am I being an idiot - Why am I getting pressure signs here?

    Did you put anti seize on the barrel threads?
Top Bottom
Back
Home
Forums
Merch
Alerts