Search results

Search the forum Search Articles
  1. stangguyaz

    AR10 Parts Identification help

    Ok so I have been looking some more at pics online looks like the firing pin is Armalite from what I have seen but the bolt carrier is stumping me. Most all of the Dpms models have flat spots cut lengthwise down them the smooth sided models I have found have the gas relief holes located in the...
  2. stangguyaz

    AR10 Parts Identification help

    So I called Armalite today to ask them about some extraction issues I gave them the serial number on my rifle and found out that my lower was sold as a stripped lower so my gun is a parts gun or custom of some sort. I dis assembled the rifle and took some pics of the bolt carrier group and upper...
  3. stangguyaz

    OCW iterpretation help where to go from here

    Thanks
  4. stangguyaz

    OCW iterpretation help where to go from here

    I don't use parallax to focus sight picture I do exactly as you say the knob is just so hard to turn its hard to get it perfect. if it was a $600 dollar scope I wouldn't be pissed if it was a little out of focus but I payed more than double that for it, not that it isn't in focus because it is...
  5. stangguyaz

    OCW iterpretation help where to go from here

    I love the scope glass is awesome but I hope it gets easier I seemed to be able to get the parrallax correct at 600-1000yds but not 100 wonder why
  6. stangguyaz

    OCW iterpretation help where to go from here

    Should I try it in the lapua brass
  7. stangguyaz

    OCW iterpretation help where to go from here

    Not sure on the vintage of the Hornady brass I bought it as once fired from a local distributor. but that may explain it
  8. stangguyaz

    OCW iterpretation help where to go from here

    Thanks Dan thats exactly what I was looking for. I will research the bolt lugs and check it out and reload with the loads you have recommended. I will do a better job of getting my dots level and a little closer together next time as well. I think you are right on the parallax adjustment, I am...
  9. stangguyaz

    OCW iterpretation help where to go from here

    I will try that Thanks
  10. stangguyaz

    OCW iterpretation help where to go from here

    yes its a .308 I did it with the Varget should I clean it and do it again ive been using Varget exclusively to no avail that's why I was trying the 2 different IMR powders the gun will shoot sub moa 5 shot groups all day long with FGM maybe its my reloading?
  11. stangguyaz

    OCW iterpretation help where to go from here

    Well guys I have been trying to find the right load for my Remington 700 SPSS .308 without much luck. So today I tried Dan Newberrys OCW test and need some help as to where to go from here. first set of .75'' dots were shot with 175gr SMK's in Lapua brass and IMR 4064 loaded to 2.801 aol...
  12. stangguyaz

    .308 gas gun load

    Bullet :Sierra 155 Palma Match Powder: Varget 42.5gr (if I go much over 43gr I start having issues) Case: Misc military Oal: 2.80 Primer CCI I shoot this load in my Armalite Ar10 22'' barrel I get consistent sub moa groups at a 100 and have used it with decent results out to a thousand yds. I...
  13. stangguyaz

    Bell and Carlson Stock Issues

    If you can rock your action in your stock like you say than you are probably torquing your action causing issues. is your barrel free floated? I have not found many guns that will shoot that well without being bedded or in a chassis. What I did after I bought my B&C was take my factory stock...
  14. stangguyaz

    Bedding a B&C medalist

    I bought longer screws and cut the heads then covered the threads with one layer of tape then shoe polish. You just need them to make sure your action screws line up.I have found electrical tape works well to hold it in place you can also use surgical tubing but most everyone has electrical...
  15. stangguyaz

    Bedding a B&C medalist

    Well I just Bedded my B&C and I will tell you I saw a big accuracy increase so I would say go for it. To keep my barrel straight and floated in the channel I used electrical tape around the barrel in 2 places. I clearanced my recoil lug area a little but that was it. taped up the stock used...
  16. stangguyaz

    for .308 Winchester 1000 yard 168 or 175 grain and why?

    I've been shooting some practice F class matches with a 26'' barreled 700 and a 22'' barreled ar10 both consistent 10 ring hits at a thousand yards with 175smks and 44gr varget and 155palma match with 42.5 gr both are cracking loudly over the pits and punching good holes but the 155s are greatly...
  17. stangguyaz

    Hello Aaron from AZ

    Welcome from Phoenix. I shoot both bolt and Gas guns and am addicted to this place as well
  18. stangguyaz

    Hunting & Fishing Post your SMK/Match bullet kills

    Here is a few coyotes i took with 155gr SMKfirst dog was about 200 yards through the chest excited abdomen guts everywhere This one was 30 yards butt to front blew out the side taking most of the innards with it
  19. stangguyaz

    Gunsmithing Gunsmiths too busy, too "special", or what?

    +1 for Phoenix Custom Rifles they answered the phone every time I called and it wasn't often great service. and faster than they told me.
  20. stangguyaz

    Hunting & Fishing First Bull with a Bow! Colorado 2013

    That's Awesome congrats man
Top Bottom
Back
Home
Forums
Merch
Alerts