Search results

Search the forum Search Articles
  1. MDM

    Vector or 737r

    I run AI mags in my Vector/MPA combo with no issue.
  2. MDM

    Reloading Equipment Chargemaster Reducing Insert

    bump
  3. MDM

    Reloading Equipment Reducing Insert Set for your Auto Trickler

    Reducing Insert Set for your Auto Trickler - $20 shipped. Not sure where my original thread went but I'm still getting PMs about the inserts for the Auto Trickler I've been making . I've made a couple of different sized inserts that will be sold as a set. The inserts are a taper fit into your...
  4. MDM

    Axiom vs Vector Curtis Actions

    I've been running a couple of Axiom since their initial run and got a Vector a few months back and they have been great. 10 in/lbs for me on the Vector.
  5. MDM

    Reloading Equipment Chargemaster Reducing Insert

    Guys, PM me if you need one. Thanks.
  6. MDM

    Reloading Equipment Chargemaster Reducing Insert

    Yes, been making them for 5 years now, just pm me if you need one. I have guys using them in the Hornady and Lyman. Not a lot of Lyman users but several Hornady. I just need you to measure the ID of the tube and I'll get you one that will fit. Thanks, Dave
  7. MDM

    Reloading Equipment Chargemaster Reducing Insert

    bump
  8. MDM

    NIB Proof Research AI Prefit 6.5 Creedmoor

    bump
  9. MDM

    NIB Proof Research AI Prefit 6.5 Creedmoor

    NIB - Proof AI prefit in 6.5 Creed. Fits AX308/AT/AW/AE S 24”, 8 twist threaded 5/8-24. Part number 110188 as seen here... https://www.proofresearch.com/the-products/barrels/steel-accuracy-international-barrels/ SOLD
  10. MDM

    Curtis Custom Actions (Vector)

    Way less.
  11. MDM

    Reloading Equipment Chargemaster Reducing Insert

    bump
  12. MDM

    Vector Barrel Install

    Maybe one day a stage will require you start with barrel in hand...
  13. MDM

    Night Vision PVS-9 simrad

    My 203 is the same as the above pics.
  14. MDM

    Reloading Equipment Chargemaster Reducing Insert

    bump
  15. MDM

    Gunsmithing Magazine pressure causing feed problems

    Mpa has a fix coming for this. A small plastic piece that fits into the chassis near the mag latch the keeps this from happening. I epoxied a piece of .125” aluminum in place that does the same thing. Works so well I did it on all 3 of my chassis.
  16. MDM

    Actions that accept DIY barrel changes (Savage, Rem-age, etc)? and question about Tikka barrel swap

    No, you misunderstood me and maybe I misunderstood you as well. I'm talking about using the action as intended with a shouldered barrel. If you use Remington prefit, you obviously need to use a barrel nut and torque the nut as you normally would and not use the screws. That's why I said "want...
  17. MDM

    Actions that accept DIY barrel changes (Savage, Rem-age, etc)? and question about Tikka barrel swap

    I wonder how I ever trusted a direct thread suppressor, yet somehow they just stay put. With those two screws, that barrel isn't going anywhere. In fact, it likely wouldn't go anywhere without the set screws with a properly machined tenon and barrel snapped into place, use some anti-sieze or...
  18. MDM

    Actions that accept DIY barrel changes (Savage, Rem-age, etc)? and question about Tikka barrel swap

    In most cases, all it takes to put a Remington prefit on an action that does not have a nose recess is to cut the recess off the prefit. Should take your smith 15 minutes. I've done this to a couple prefits to put them on my Curtis Axiom.
  19. MDM

    Chambering up a Curtis Vector

    Chambering for a Vector. After I got it finished, I went outside and shot 5 thru it using some old fire form loads I had been using in my other rifle. First 5 rounds (prone,rear bag). Then I loosened the set screws on the tenon, pulled the barrel, then reinstalled. No need to remove...
  20. MDM

    Reloading Equipment Chargemaster Reducing Insert

    bump
Top Bottom
Back
Home
Forums
Merch
Alerts