Search results

Search the forum Search Articles
  1. K

    Induction Annealing Discussion

    Does anyone else warm their induction annealer up with scrap cases? I run a dozen scrap cases through before I anneal the good stuff. This brings the system up to temp as the annealing cycle time is effected. Fluxeon recommends this.
  2. K

    Induction Annealing Discussion

    I also use a Fluxeon Annie, on 6.5 CM cycle time is 1.8 hornady, 2.0 nosler, 2.4 Lapua. I built a trapdoor setup that controls the position of the brass in the coil. When cycle is complete I open the trapdoor and the brass drops into a container. Might add that I am using the water cooled coil.
  3. K

    Decapping & Resizing Lapua 6.5 Creedmoor

    Deprime with Redding decapping die, comes equipped with small dia pin. Previously used hornady decapping die on hornady brass but they don't have a small dia pin. For sizing I'm using a Redding fl bushing die with Redding competition she'll holder to bump shoulder .002. Bullet seating with a LE...
  4. K

    Broke the LabRadar AGAIN !

    Triplebull, what tripod is that in your picture?
  5. K

    Suppressors Buildup inside suppressor

    i have approx 700 rounds through my AAC 762-SDN-6, mostly 6.5 Creedmoor. Looking into the can from the back end I noticed a buildup on the first baffle. Should I be concerned? Do I need to clean this if so how. I always heard only rimfire cans need to be cleaned.
  6. K

    What's your favorite die set for 6.5 Creedmoor?

    For 6.5 Creedmoor I use Redding S type bushing die. Bushing matched to brass neck thickness for neck tension. Bullet seating is done with L.E. Wilson seating die on arbor press. With ref. to neck tension I additionally anneal brass on each loading.
  7. K

    Range Report Calculating BC with numbers from Labradar

    Thanks for the info, will be interested in your work up infor
  8. K

    Range Report Calculating BC with numbers from Labradar

    I am shooting bullets with no verified BC. 136gr EPS BTHP in 6.5 Creedmoor. They are very consistent weight and base to ojive length. I used the muzzle velocity 2805 and 100yd velocity 2640 f ok my Labradar to calculate a G7 on JBM sight and got .271. I'll be curious to see how this works out...
  9. K

    Help me choose a Brass trimmer

    I'll second the little crow trimmer "WFT". I started accumulating them before they introduced the switchable chamber model so I have ( 308, 223,300BO, 6.5 Creedmoor). I had a bench top drill press that I use the trimmers in.there are several good videos on YouTube.
  10. K

    Sizing lube removal

    I am using 10% lanolin in 99% alcohol. Seems I read on line that lube left on cases would result in excessive bolt pressure
  11. K

    Sizing lube removal

    i currently wet tumble, dry in dehydrator, anneal, spray lube, resize, if small batch I spray with alcohol and wipe to remove lube. What is your preferred method to remove lube from say 100 pieces.
  12. K

    What press/presses are you using?

    RCBS Pardner-decaping rock chucker-resizing arbor press/LE Wilson seating Dillon 550-pistol rounds spolar 12 thru410 skeet ammo
  13. K

    Problem with 6.5 Creedmoor lapua brass

    Hornady brass ejects perfectly
  14. K

    Problem with 6.5 Creedmoor lapua brass

  15. K

    Problem with 6.5 Creedmoor lapua brass

    It must be engaging to some extent as the case is pulled from the chamber but falling loose from the bolt before the case mouth clears the ejection oort
  16. K

    142 SMK and jump

    I Jump them .020 on 42.3gr H4350 in Hornady brass
  17. K

    Problem with 6.5 Creedmoor lapua brass

    i have a issue with fired brass not being ejected from the gun. Upon cycling the bolt (m700) the brass is pulled from the chamber but is left laying loose on top of the next round in the mag. No issue with hornady brass.
  18. K

    136gr Scenar for 6.5 Creedmoor

    Brux, H4350 your powder?
  19. K

    136gr Scenar for 6.5 Creedmoor

    Looking to work up a load for these, any experience good or bad.
  20. K

    Any one have a hornady load manual? Looking for 7-08 loads using 139gn GMX

    41.3gr 2400 fps to 47.1gr 2800 fps per hornady manual
Top Bottom
Back
Home
Forums
Merch
Alerts