Search results

Search the forum Search Articles
  1. Redcreek1

    Si defense

    Here are some pics of a builds I did with their 308 upper/lower sets.
  2. Redcreek1

    Gunsmithing Heat Tolerant Stencils To For Cerakote

    As far as stencils go, there is heat tollerant and then there is HEAT tollerant. The most common material used is the yellow 4mil Avery and its supposedly good to 200 degrees. I say supposedly, since even if run at lower than 200 degree temps it a bitch to get the stuff off after it cools...
  3. Redcreek1

    Possible .458 Whisper Type Semi Auto gun

    Or, you could just go with the .458 SOCOM, which is a proven cartridege and has commercially available ammo, brass, dies, barrels, guns, uppers, etc..
  4. Redcreek1

    Gunsmithing Best Cerakote Color to Match McM. Woodland Stock?

    Re: Best Cerakote Color to Match McM. Woodland Stock? NIC has several McMillan specific colors, such as McMillan OD Green, McMillan Grey, etc. You can see a list of colors at www.cerakoteguncoatings.com
  5. Redcreek1

    Gunsmithing Finding a gunsmith in utah

    Re: Finding a gunsmith in utah <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: golden</div><div class="ubbcode-body">I thought I had a reputable gunsmith that would finish a couple of odds and ends, but after all sorts of ridiculousness, I am trying to find a good...
  6. Redcreek1

    Sidearms & Scatterguns Glock 20 10MM to .40 Cal.

    Re: Glock 20 10MM to .40 Cal. We have done several Glock 20 custom builds that included the KKM 10mm/40 S&W conversion barrel for running 40 for practice or range work and they work great.
  7. Redcreek1

    Gunsmithing Gas Port hole size

    Re: Gas Port hole size Gas port size depends on the lenght of the barrel relative to the gas port location, as well as caliber. Since this is a 6.5 Creedmore, I am assuming you are running a rifle length gas tube and at least a 20" barrel? I would go with a .093 to start, which is pretty...
  8. Redcreek1

    Gunsmithing 140 Berger in 6.5 Gets Stuck In Feed Ramp GAP 10

    Re: 140 Berger in 6.5 Gets Stuck In Feed Ramp GAP 10 There are two options. 1.) Only use tangent ogive bullets. 2.) Open up and pollish out the M4 cuts in the feed ramp and blend them in with the lower and you should be fine. (you need the proper tools and knowledge for this option.)
  9. Redcreek1

    Gunsmithing Need glock night sights installed

    Re: Need glock night sights installed Just about any gunshop with a gunsmith, and even some without, will have the tool to change out Glock sights. Most only charge in the $25 range to do that.
  10. Redcreek1

    Gunsmithing Applying Cerakote

    Re: Applying Cerakote <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: 308FMJ</div><div class="ubbcode-body">Ernie, with one pass down and back up with a wet look about how thick will the Cerakote be? Mil thickness i guess. Jim </div></div> Done correcly, the...
  11. Redcreek1

    Gunsmithing Applying Cerakote

    Re: Applying Cerakote <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: TXSTDU</div><div class="ubbcode-body">The HVLP gun I have has a .6 tip vs a .8 that Cerakote recommends. How big of an issue it this or can I just add a little more paint to the ratio...
  12. Redcreek1

    Gunsmithing Applying Cerakote

    Re: Applying Cerakote Thanks
  13. Redcreek1

    Gunsmithing Applying Cerakote

    Re: Applying Cerakote "One pass" is one downward stroke and upward stroke. If your HVLP spray gun is set up right and you have the pressure and pattern properly adjusted, and are four to six inches from the part, you should get a wet look to the part. If you mixed for a matte sheen then...
  14. Redcreek1

    Gunsmithing AR10 Barrel Extensions????

    Re: AR10 Barrel Extensions???? No, they are a DPMS pattern barrel extension. The Armalite pattern is much longer than the DPMS and are not interchangable.
  15. Redcreek1

    Gunsmithing shoots WAAAAAAYYYY to the left

    Re: shoots WAAAAAAYYYY to the left <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: ykrvak</div><div class="ubbcode-body">I picked up a 700 243 from hide member about a year and a half ago with the intention of rebarreling it to a 7-08. So, I picked up a 7-08 take...
  16. Redcreek1

    "Assault" rifle prices since Newtown

    Re: "Assault" rifle prices since Newtown <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: stel</div><div class="ubbcode-body">After reading this thread some of the replies have me scared. There are members here who have no clue I can not believe some of the crap...
  17. Redcreek1

    "Assault" rifle prices since Newtown

    Re: "Assault" rifle prices since Newtown <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Rainier42</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Matt Waage</div><div class="ubbcode-body">I hate the...
  18. Redcreek1

    "Assault" rifle prices since Newtown

    Re: "Assault" rifle prices since Newtown <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: redneckbmxer24</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: RedCreek</div><div class="ubbcode-body"> I'm glad...
  19. Redcreek1

    "Assault" rifle prices since Newtown

    Re: "Assault" rifle prices since Newtown <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: Jacklulu</div><div class="ubbcode-body">I live in a Very Restrictive state for Gun Ownership, and also Very close to Newtown Ct and have contact with people from that...
  20. Redcreek1

    "Assault" rifle prices since Newtown

    Re: "Assault" rifle prices since Newtown <div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: redneckbmxer24</div><div class="ubbcode-body"><div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: JGrelle</div><div class="ubbcode-body"><div...
Top Bottom
Back
Home
Forums
Merch
Alerts