Search results

Search the forum Search Articles
  1. m1match

    Imr4451 vs h4350 6.5cm

    In my rifles when my load development went up to 42.5 gr. of 4451, my primers were still ok but they were getting pretty flat and my accuracy at 42.5 of 4451 was not as good, so I backed off to 41.8 grains. The curve of powder charge vs. velocity also was flatter at 41.8 grains indicating more...
  2. m1match

    Imr4451 vs h4350 6.5cm

    When I worked up IMR 4451 loads I think I started around 40.0 grains and worked up from there.
  3. m1match

    Imr4451 vs h4350 6.5cm

    Shooting Hornady 140 ELDMs, my H4350 load was Hornady case, CCI BR2, 42.5 grains of H4350 giving excellent accuracy and about 2820 fps in a 24" Rock Creek barrel. My IMR 4451 load was the same bullet, case, and primer, 41.8 grains of IMR 4451 giving about 2700 fps and excellent accuracy. So...
  4. m1match

    POLL: Most comfortable Stock or Chassis for YOU?

    For PRS type shooting, the Manners TCS is my favorite stock. For a more hunting type stock, I've got a Manners T2AGAP that would also work well (except for the red, white, & blue Americana finish!) I'm thinking that one of these days I might have to try the ARC Xylo, it looks really interesting.
  5. m1match

    Accessories WTB Atlas BT10 LW17

    PM sent, I have one I'll sell
  6. m1match

    Accessories WTB atlas bt10-nc v8 bipod, aac 51t 30 cal 5/8x24

    PM sent I have an Atlas BT10 NC
  7. m1match

    CCI 450 vs. CCI 41 primers

    I've used CCI 41s for years interchangeably with CCI 450s EXCEPT in 30 Carbine. The CCI 41s do have a slightly different anvil geometry and they are harder to set off. In 30 Carbine, I was getting about 1 in 5 light strikes which a 2nd strike would not set off. This was in a rifle with a new...
  8. m1match

    6.5 CR w/IMR 4451

    An extremely common load for IMR 4451 is my 41.8 gr load which is above the published Hodgdon max, but this load show no signs of pressure and my Hornady cases have lasted 7 reloading with no signs of loose primer pockets. My H4350 load and a 140 ELDM is 42.5 grains and again it's above the...
  9. m1match

    6.5 CR w/IMR 4451

    I just finished going through 16 lbs of IMR 4451 and if I didn't have 40 lbs of H4350, I'd still be using it. That 16 lbs loaded over 2,500 rounds of ammo. I found it to be fairly temperature stable, but not as temp stable as H4350, had excellent accuracy at velocities within 50 fps of my H4350...
  10. m1match

    Rifle Scopes Weird marks on inner turret PSTgen2

    That looks like the area that the set screws that clamp the outer turret make contact with so those marks would be normal.
  11. m1match

    Accessories PVA Jet Blast 6.5 5/8x24 black nitride

    PM sent, I'll take it.
  12. m1match

    How to tell if I have Weaver or 1913 rings

    https://en.wikipedia.org/wiki/Picatinny_rail Google is your friend read to the end for Weaver specs.
  13. m1match

    How to tell if I have Weaver or 1913 rings

    The cross slot of Weaver rail is narrower than the cross slot of a 1913 Picatinny rail. You can use a Weaver ring on a Picatinny rail but probably not the reverse unless you Weaver rail has wider than usual cross slots
  14. m1match

    What is this? AI MKIII

    You posted a photo of your rifle- are you sure the rubber butt pad on your rifle doesn't come off by loosening an Allen wrench bolt in the middle of the pad? If it does, then the spacer in your first photo goes between the rubber butt pad and the plastic length of pull spacers.
  15. m1match

    What is this? AI MKIII

    That is the adjustable buttplate spacer that bolts to the stock side of the AI. The rubber buttplate then bolts to the sliding stud in the middle and can be adjusted for height and tilt. Here's pictures from my AI AW of similar vintage. the first picture is of the parts. The part you have...
  16. m1match

    Broken tips on Hornady 6.5 140 ELDMs

    Anybody else see this issue? I've shot almost 5000 Hornady 140 ELDMs since 2017 and until this month have never seen this before. A couple of weeks ago I was shooting a match and had a round go way low at 600 yds that was not due to me making a bad...
    • Thread
  17. m1match

    Range Report Broken tips on Hornady 6.5 140 ELDMs

    As the OP, here's an update on my specific case. Hornady sent me a shipping tag to return the unused 140 ELDMs to them and they will ship me replacements.
  18. m1match

    Manners Colors - Actual Pics?

    Here's my Blue/Black TCS- I think this might be one of their best colors
  19. m1match

    Rifle Scopes Scope Windage Zero Problem

    I think your S&B actually has much more windage than 6 mils each direction from optical center but the turrets are stopped so they won't give you more than 6 mils each direction. Use the zero stop to make sure you have enough travel to get to your zero then use the zero stop to set the turret to 0/
  20. m1match

    6.5 Creedmoor load data question

    Ejector marks are not good, I probably wouldn't push it. You also have a flattening of the velocity curve between 41.2 and 41.4 plus your testing at 41.2 had the lowest ES and SD of your data. For many years I loaded H4350 and 140 ELDMs at velocities of around 2730-2750 with excellent results...
Top Bottom
Back
Home
Forums
Merch
Alerts