Search results

At one time some one made a globe front sight for an M1 Garand. Any one have a source for one?

Where did all the IMR 4064 go? Used to be available any time I needed it, now it's nowhere to be found.

Any one heard of this trigger? Called a Tri Ad trigger.

Any one see this yet at the shot show ? Christensen Arms — Ranger 22 Rimfire

On my new 6.5 Grendel build ,every thing functions fine except the bolt doesn't lock back most of the time on the last shot. Locks back fine by hand. Load is the same that functions fine in my other two Grendels .Tried stretching the mag spring and different mags and still doesn't lock back .Im...

what does all the stuff after the numbers mean ? 2.730" OAL

I load 55 grain fb hp bullets in my ar15 with W748 and have been for a long time with no problems . Some one gave me some AA 2230 powder and I loaded the same load using the AA2230 powder . It seems to shoot just fine but every ten shot mag has one or two rounds that has a duller sound .I though...

Has any one had experience with ARD barrels .They are from ar15 depot. Im looking for a 24 inch bull in 308 . I have been getting a run around for about 9 months now from Lothar Walther and am about to cancel the order .Arnie

What are some reasons for this to happen .Stock mill spec trigger and hammer assembly . 24 inch barrel ,rifle length gas tube ,A2 stock . I cleaned the whole upper with a sonic cleaner and lubed it all up .I did clean a bunch of grease off the buffer and spring that I had put there to quiet it...

I didn't get to talk to the guy much but he said his 308 AR has a spring on the firing firing pin and its not an Armalite but said it was a dpms style made by Larue . Any one have one of these to confirm or any other dpms type BCG with a spring on the firing pin ? Arnie

Any one know who makes this carrier ? The X is stamped on the lower left area close to the front . Its pretty big and thick so it might have been done with a laser . Arnie

Does anyone have any experience with AR slam fires and what can cause them ?.I'm having this happen every so often with my 308 . I single feed it and once in a great while it will slam fire when I release the bolt and let it fly home using a Bob Sled . This happened twice to me Tuesday...

Any one know of one being made for sale . Arnie

Any one use this brass .I have about 500 pulled down never fired . Putting the same load in a Winchester case and an IVI case has a noticeable difference in powder level .If I remove 2 grains from the IVI case ,it sets level with the Winchester load . I'm guessing dropping the load 2 grains...

Planning to build a target bull barrel 6.5 Grendel or clone on a new side charger receiver . .Whats your opinion on Krieger barrels ,Les Baer barrels .Lothar Walther barrels ,and Bartlien . Im leaning to Krieger .Arnie

I have installed one in triggers in a DPMS type 308 AR .Every thing works fine when the upper is off the lower but when I put it together and cock it ,the trigger wont fire the rifle .If I put the safety to safe and then to fire it will work for that one trigger pull .I also hear a click in the...

Im sure i will open a can of worms here but what is your favorite muzzle brake for an AR in 308 ? I shot one yesterday with what he said is a PVI muzzle brake but cant find them in a Google search .This brake seemed to work very good . Arnie

Check Midway's site .They are closing out 6.5 Creedmoor brass for some reason . Arnie

Was having jamming problems with my new build 308.The fired case would turn 180 in the receiver and the bolt head would smash the mouth of the case . Put in a stronger extractor spring and that showed some improvement but still jamming and now stove pipe also . I then put in a noticeably...

Is there a rule to follow concerning barrel torque on say an AR15 compared to a DPMS 308 and a 6.5 Grendel ? Or are they all pretty much the same and what would the high and low specs be ? Arnie