Search results

Stock Cross 6.5 18" here. When new this had the misaligned hand guard which appears to be a common issue but also simple to address. After 3 range trips and checking the scope and scope mount screws few times I have confirmed that this has very noticeable cold bore shift. I'm seeing impacts...

Selling the BLK LBL hand guard with integrated bipod for Tikka TAC A1. This is the 15" version. Two sets of bipod feet are included, one set with soft rubber pads and another with sharp spikes. Spiked feet were a ~$100 option about 2 years ago. Will add pictures later. In full working order and...

No longer available.

SOLD

Minox ZP5 is still available. Price ($2400) is firm but includes domestic air shipping. I have also an ad up for ATACR 7-35 that I'm selling. I need to sell one of these and keep the other one. They both serve the same purpose - solid long range scopes with tree reticles. Happy to answer questions.

ATACR 7-35 T3 is still available.

ATACR 7-35 still available

Sig Cross 6.5 here. Purchased new, so far 70 rounds fired. Is anybody else seeing feeding issues with the Lapua 6.5 SRP brass? It seems that Lapua brass base is just few mils too wide for the extractor to slide over the rim. So round comes out from the magazine, chambers but bolt cannot be...

Original ad updated with closeup high res pictures of the glass. Glass is flawless.

Used NightForce ATACR 7-35x56 scope with Tremor3 reticle. NightForce SKU# C571. Has the red/green illumination like most NF scopes. Nothing wrong with the scope - adjustments track, no damage to lenses, very faint ring marks. Label at the end of the box includes the sticker "Cosmetic Blemish" -...

One owner, clean Minox ZP5 with the MR4 illuminated tree reticle. Comes in original box with all included accessories. Scope has been out in the field for fewer than 10 times total, no competitions, not tossed around. Only visual blemishes are the ring marks around rear ring. Glass is flawless...

Quick update: I have been testing Ramshot Enforcer for full power Blackout loads. This seems to offer bit more velocity compared to H110 or Lil Gun. With 18.8gr of Enforcer I'm sending the 110gr Vmax at 1900+ fps from 5.5" barrel, which is comparable to Hornady factory loads. Also works great...

I have not been able to replicate the Hornady Black 110gr V-max load. Labradar clocks this Hornady load at 1910fps from 5.5" barrel. When I filled the case with H110 (21-22gr), with room left for V-max bullet, I was at low 1800fps. At the same time load felt overpressure, slightly "violent"...

2400fps from 16" barrel sounds interesting. Hornady advertises 2375fps from 16" and same load does 1900+ from 5.5". Are you a commercial ammo vendor here on SH?

Maybe I should have mentioned earlier that I have a 5.5" barrel. Some slower powders may provide speed in longer barrels but with short barrel you get unburnt powder and maybe a nice fireball. I ran the QL numbers for 4100 and CFE Blk powders mentioned in this thread. 4100 produces speeds very...

QL has the H110 burn rate factor as 0.8000 but to make the QL velocity match the measured speeds I need to up this to 0.95. This may be due to H110s temperature sensitivity, recently its been 95-100F. Using burn rate of 0.95 QL shows that with 110gr projectile I can use 17.5gr of H110 while...

Any way to find out what powder Hornady uses in their Blackout 110gr factory load? This produces impressive speeds from short barrel. Cannot replicate the speeds with H110 or N110.

Purchased in 2020, used to load 7lbs of powder. Everything works, all accessories and original packaging are included. Price includes UPS/Fedex ground shipping in lower 48.

Would gunsmith be able to replace the SMR factory barrel with another factory barrel?

So far I have gathered: 1) MRADs with folding stock and replaceable barrels are sold out nationwide and new production is 12+ months out 2) For 300 Norma the preferred or safer twist option is 1:10. I do see MRAD SMRs in 300 Norma readily available but these are with the 26", 1:8 twist barrel...