• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. D

    Steiner T6xi

    Yeah my windage feels great. I think I will use it for a few range trips to see if it loosens up. Maybe it will start to feel better. If not I’ll reach out to them.
  2. D

    Steiner T6xi

    Shoot, that’s a bummer. I think I’ll at least try to call them and see what they say about sending it in.
  3. D

    Steiner T6xi

    Just received a 5-30x56 and the elevation turret locking mechanism is very tight. Additionally, it doesn’t completely lock the turret. Trying to unlock by twisting the top the turret did move a few clicks. Anyone else encounter this?
  4. D

    SOLD KRG Bravo Chassis 700SA

    I’ll take it. Unable to PM you.
  5. D

    Firearms Desert Tech SRS A2 nightforce NX8

    Still available?
  6. D

    SOLD Desert tech srs A2

    PM sent
  7. D

    Bix’n Andy issue in Zermatt TL3

    Thank you so much. This was my issue and with a little bit of polishing with a dremel I got it fixed. The Phillips head screw that holds that silver safety knob on is pretty finicky. I stripped it and ended up pulling the whole safety lever off to be able to polish the area I needed to get to.
  8. D

    Bix’n Andy issue in Zermatt TL3

    The trigger has clearance from the bottom metal and I think you’re right about the bolt not being the issue. earlier I adjusted the sear screw quite a ways out and it would still drop from time to time. I have not put the medium sear back in because when measuring I’m sitting at 0.154 inch...
  9. D

    Bix’n Andy issue in Zermatt TL3

    Ok, I’ll start there. The bolt does look close to the front of the stock bolt inlet but I didn’t know that could cause my issue.
  10. D

    Bix’n Andy issue in Zermatt TL3

    Hey y’all, I’m struggling with the firing pin dropping on bolt close with a Bix’n Andy tac sport pro in a Zermatt TL3. I changed the top sear to the low 3.6mm sear and followed the instructions on adjusting the sear engagement screw. I can get the trigger adjusted so it will cock and hold...
  11. D

    Night Vision PVS-14, L3 WP and Wilcox J arm, G22, Team Wendy CF bump helmet

    Do you have a rough idea of how many hours on it?
  12. D

    Optics Vortex Viper HD 10x42

    PM sent
  13. D

    MPA complete rifle?

    Bringing an old thread back but just curious if there is any more experience out there with these rifles. I am considering one and would like to hear if anyone else has used one. And if so where is the best place to buy one. So far I've found them at xtreme guns and ammo and the MPA website...
  14. D

    Mesa bottom metal/Magpul magazine issue

    That’s a good idea. I’ll give them a call tomorrow and see that they think. Thanks for the input. Hopefully it’s just a spring issue. I can’t think of anything else at this point but y’all know a lot more than I do so I thought I would ask.
  15. D

    Mesa bottom metal/Magpul magazine issue

    The latch seemed like it didn’t provide much tension so I did remove the release and stretched the spring very slightly. Latch is tighter now but I haven’t been able to test if it fixed the issue.
  16. D

    Mesa bottom metal/Magpul magazine issue

    Yes, it does snap all the way in. I can not pull the magazine out by hand once snapped in. I’ve used Magpul magazines as well as a MDT polymer acis style mag that also comes unlatched but does not fall all the way out because it’s a much tighter fit than the Magpul magazines.
  17. D

    Mesa bottom metal/Magpul magazine issue

    I have a greyboe stock with a Mesa M5 bottom metal in it that is dropping mags after I take a shot. The odd part is it only drops the magazine if there are 2 or less rounds in the mag. When I load up ten rounds I can fire 1-8 without an issue but the last few shots always cause the mag to fall...
  18. D

    Rifle Scopes Very little elevation adjustment after zeroing

    After reading about the Burris rings I like the idea of buying them instead of a new rail.
  19. D

    Rifle Scopes Very little elevation adjustment after zeroing

    Thank you for the replies. I will order a 20 or 30 moa base to increase my elevation adjustment. However with a 30 moa will I have a hard time zeroing it at 100 yards?
  20. D

    Rifle Scopes Very little elevation adjustment after zeroing

    Hello everyone, I am very new to long range precision shooting and just recently purchased a savage stealth in 6.5 Creedmoor. I put an Athlon Argos 6-24x50 on top inside weaver tactical six hole rings. I did not change the base to a 20 moa base. After zeroing the rifle at 100 yards I only...
Top Bottom
Back
Home
Forums
Merch
Alerts