Search results

Seeing if anyone might have a factory chassis for sale for Ruger American Rimfire....mines a 17 hmr if that matters...thank you God Bless

If I have this wrong please go easy on me.....wanting to trade my short action Remington 700 with standard bolt face its untrued for a Remington 700 223 action that is also untrued...I think the serial number I have is a candidate for an M40 build....I had the bolt handle threaded like a...

400 midsouth match monster bullets for sale 107 grain 6mm...100.00 shipped...thank you and God Bless

I have a Bering Yoter 35 just wondering if anyone ever puts a scope cover on for not getting too beat up....I'm a poor so wanting to make this last a while is important. Thank you for any replies Very Respectfully Submitted

I apologize in advance if this is a dumb question....I finally got my AB Raptor in hand and looking at covers....with the reflex this darn thing is 12 inches long....I dobt want to buy two covers....is it ok to just cover the baffle section...will a cover only on the baffle section be enough to...

Looking for opinions on thermal scopes....not clip-ons....in the 5 thousand dollar range. This is my first thermal scope. I've been watching you tube videos until I'm cross-eyed....Pulsar Thermion..Iray Rico...AGM...Bering...not sure what to do here.....do I save up for a Thermion Duo....does...

2 boxes 500ct DTACs....same lot "60115" I can't get that picture to load...415.00 shipped and insured for both boxes or 210.00 for one to your door PP F&F...personal check "ships after clears" or M/O...any questions shoot me a PM please...please PM with any questions or Ill PM my number to...

Threaded or unthreaded used Glock 23 barrel is fine just putting something together for the house.... Thank you guys for all you do on here Semper Fi

Seeing if someone might have a used Impact 22BR or 22 Dasher barrel at least 8 twist laying around not in use. Thank you gentlemen for everything y'all do on here Or a Remington 700 Remage barrel thank you guys

Seeing if someone might have an extra barrel laying around for an Impact....Looking for a 6BR 1-7 1-7.5 twist preferred.....I might be leaving some information needed out if so I apologize.....Thank you for any help/advice Chesty for President

Purchased used Remington 700 barrel in 6 Dasher....showed up in perfect condition and is an absolute hammer....couldn't afford a new one so a used one will keep me shooting....cannot thank you enough

New guy here been reloading for about 25 years never had this happen....Got in a hurry sizing Dasher brass to shoot tomorrow and crushed/cut the hell out of the end of my finger....got it hung between the case mouth and bottom of the die even the primer pin got some haha......never realized...

Box of 80 Berger 82 grain BT Target Part#22424

Its about 180 pieces of Winchester 7 WSM brass I resized to 300 WSM.....Once fired Winchester brass Ill cover shipping maybe someone can use this...Thanks for looking

I have 90 JLK 110 grain bullets to someone that wants to try them out....Ill cover shipping.....Paying it forward....

I have 75 JLK 115 grain bullets.....Free to someone that maybe wants to try them out because this guy cannot afford to shoot these all the time.....ill cover shipping.....Paying it forward

Paying it forward maybe it'll get someone getting into a Dasher out shooting.....about 160 pieces some are new never fired....Thank you for looking

If I am asking something that is out of line please lock me on....Looking for retired barrals NON trued Remington 700/700 clone tenon, prefits or shouldered in 6BR 6BRX 6 Dasher 6.5 Grendel 6 Creedmoor 6.5 Creedmoor 1-8 or faster.....Just trying to save a few bucks by setting back or...

I went to the Meopta website didnt find anything....I see Meopta 56mm Meostar ones are those the same....are there any other 56mm shades that will screw on....any help is much appreciated....if this is in the wrong area I apologize in advance thanks again

I did three of these to see how they came out. I'm pretty sure I overdid it. Please go easy on me this is my first try at this with some random brass