Search results

Sleeve of 5 boxes (500) $150 + shipping priority mail is only $8.

$55 shipped

Bought a gap rifle from him,really good guy

Just picked this one up and checking it out before i shoot it I noticed that the bolts really stiff to close on new factory ammo,it will close but it takes some force,it closes hard enough that it leaves shiny marks on the base of the brass.I have a headspace gauge and measured the new brass...

Bought a HS precision from him ,shipped instantly.

OCW test link to pic I shot some test loads yesterday to try out the OCW method and heres the results,tell me which load area you would go with. I shot these at 210 yards just to see how my gun liked them. Temperature was around 85 and mirage was pretty bad. I only loaded up two bullets for two...

If any of you have used a leupold boresighter you know it has a MOA scale built in to check scope tracking and it works just fine with MOA adjustments. My question is how do i check a scope with MIL turrets using a MOA scale or can it be done? How much would 12 MOA or MILS (1 turret rev) read on...

Im having trouble getting used to the 20" barrel on my AAC rifle so i figured i would try a brake on it to try to tame the recoil and muzzle jump a bit.Any of you guys use this brake ? Is it going to be so loud its miserable to shoot?

Mine has the factory remington hard butpad on it and i have a limbsaver that looks like a perfect fit. Will i ruin my stock if i remove the factory pad,i understand they are glued on. Is there anything solid in the stock for the screws to bite into so they wont pull out?

I have a long range 26" .308 with a 6-20x50 scope already set up so the 20" AAC 308 will be for shooting 600 yards + /- . I have an extra 3-10x40 leupold mildot and a SWFA 6x mildot,both have nice glass but which one would be better suited for this rifle?

I have a Howa 1500 LA , 20 MOA steel bases ,burris 30mm rings and a 16X super sniper mounted up on top. I used the thick base at the rear-short one up front mounted up my scope and used most of my adjustment to get a 200 yard zero.What have i done wrong with my setup? You can look at my turret...

I am trying to get my howa 30-06 with a wood stock set up for some long range shooting ,i installed some 20 MOA bases and tactical scope+ rings so far. This rifle has always shot under an inch at 100yds but i have never used a torque wrench on the screws ,just hand tight on them. Whats a good...

Could this be caused by a trim die? I could not get the bullets to seat and i have used this brass+dies before.It's .243 by the way.

It's been 20+ years since i took the test in high school so i dont remember how to read the results so i need a little help. My 16 y/o son took the test last week and is interested in joining but im not sure i want him to at this time .Can some one look at the test results and tell me what kind...

I got a new one for xmas and so far i have only used it inside but all my other gear is in my garage and it's not insulated,does the cold weather affect them or will it work just fine as long as i give it a 30 min warm up time?

I put some rounds together this morning to try my first ladder test.It was about 40 degrees out,wind was calm.I set up my target up at 250 to 300 yards out.I started with some hornady 168 bullets loaded from 44 to 46 grains in .2 increments with varget.I loaded the sierra 175's with 43 to 45...

Any body know where i can get one of these? I think all i need is a washer to put under the knob . I have about 2 revs below my zero position and i seem to miss it every time i dial for range and go back to zero

I need my mag box a few thousands longer to seat my .308 bullets out farther,will it destroy my mag box if i try to lengthen it a little or should it be left alone? I think mine measured 2.845 and i would like it to be around 2.9

I have read alot of the info already and just want some opinions on my starting load. 43 grains of varget seems to work for alot of guys loaded at 2.8 OAL ,is this a good starting point or is 43 grains varget too much to start with?Can somebody tell me a good way to tell when i have my OAL close...

Are the lee RGB dies worth buying? Im just starting out and need to buy several things so i need to watch the budget.