Search results

When I joined this forum a few years ago, one of my first inquiries related to suppressing the AR-10. I already had my YHM Phantom 338 suppressor and was aware of the Arma-Lite 338 Fed 22" upper. The pictures today show the result of what eventually was a 4 year project in the making and I have...

Getting close to pulling the trigger on a clip on (Armasight CO-MR). That said, I have a couple of questions concerning the day scope. 1. does the reticle type matter? For example, I have a Leu 4.5-14x50 w/ ILL Duplex. Does illumination help you see the reticle when using the NV? Same question...

I'm looking for a system to identify my AI magazines for my Rem 700 LTR to distinguish between full power loads and my subsonics. My loads look the same externally (just change powder). Curious as to what works for some of you. Colored tape? Any advice is appreciated. THANK YOU- TX COWDOC

Thank you in advance for your advice- Looking at the Bobro mounts for a AR 10 (338 Fed) to mount a Leupold 4.5x14x50 LR (30mm tube). Thoughts on the single lever mount versus the double lever for this application? Thank you- TX COWDOC

Any input is appreciated. Looking for a cover for the above can. Measures 1.5" Diameter and 8 11/16" long. Thanks- TX COWDOC

Hello- I have an Armalite AR-10 in 338 Fed. 22" Barrel, 1:10" Twist. I also have a YHM 338 Phantom. I realize what I give up by shortening the barrel (velocity, potential gas pressure changes, etc). This will be a dedicated suppressed project. Here's where I need some guidance: 1. Hand-guard-...

Howdy All- I've learned a lot on this site for some time. I'm an experienced loader but new to the 6.5 Creedmoor with a new rifle on the way. The rifle is the Browning A-Bolt II Long Range Hunter -Composite. Twist rate is 1:8. Barrel: 26". I'm looking for either thoughts on Berger and / or...

Anyone have any leads on a cheek piece (other than factory) that works with the Barrett 82A1? Thanks

I'll be cutting down the 22" barrel to legal minimum on an AR10T in 338 Fed so that when my 338 cal can is threaded on the overall length will be managable. This rifle will be a dedicated suppressed weapon. Any concerns other than lost muzzle velocity? Thanks

What is the max cartridge overall length for hand loading the AR-10? I'm assuming that 308 Win and 338 Federal (using the same case) will be the same length? Correcto? Gracias

A relative of mine (we'll refer to him as douche bag or DB) was borrowing his father's truck and was pulled over by a deputy sheriff. Truck was searched (becasue DB has every appearance of an offender. Even talks like one). Deputy finds the US Army issue 1911A1 45ACP that DB's father has...

Say a fella wanted to sell a supressor that he purchased and decided to change directions on a project. How is that done?

I use an RCBS power trimmer and the trim mate unit to trim my brass. My question is: When chamferring the brass with the Trim Mate, does it matter whether I go inside 1st or outside 1st. How much do I bevel the neck of the brass? I'd have to admit that I'm not consistent with the length of time...

I have a YHM 338 can and would like to find / build a 338 cal rifle with as short a barrel as possible (min. legal is 18" correct?) to functionally support the can. Any rifle suggestions? Thanks TX COWDOC

I'm sure this has been discussed but could not find the thread. I have an Omega 30 for my 308 Rem 700 and was curious if if would function on an AR-10? I am a lefty so extra gas coming out of the action is not cool- Thanks TX COWDOC

I'm a southpaw shooter and would like to have a lefty safety selector on the 82A1. Does anyone make such a part. I'm assuming the AR type is not compatible- Thanks

I was loading for my buddy's 300 Win Mag and tinkered with some Trail Boss. Capacity was 20 grains. Per Trail Boss' instructions one could go as low as 70% of capacity. Well, let me tell you that 14 grains isn't enough to push that Barnes TTSX out of his 26" barrel. Talk about an Oh Sh*t moment...

I've been shooting this stuff through my 700 LRT with an Omega 30 can. Shoots like a dream. Since I'm already set to load 308 subsonic, I am curous if anyone knew what would be a comparable powder to try to match this round. Shoots well but would like to laod my own. I'm getting 2520 fps out...

Any experience on this item. I am interested in a custom turret for hunting on my 5-22-50 NPr1. Thanks

Any thoughts on how the GM215M compares to the 215 primers? Thanks