Search results

Saw this show when I was younger and it is now on the MeTV channel. During the opening of the show the Rifleman walks down a street firing his rifle' now this was a 44-40 and I counted 13 shots before he reloads. Is that possible or Hollywood?

I have just been diagnosed with HCC and I'm going in for vein mapping at Moffitt Cancer Center in preparation for injection of Theraspheres. Has anyone had experiance with this and what was the outcome?

need front sight ramp for a marlin camp 45 with approx. 1" spacing on screw holes

I was given some 308 once fired cases that are marked SSA 308. anyone know if these are military or commercial? Did a google search and all I could find was Silver State Armory.

Went to the range on Sunday, first time in a long in awhile. Savage FCP 10 5r on forth round shell casing would not flip out of bolt. Had to pull out with finger. Every thing looked ok figured it was too many loads on FGMM brass, next shot bolt did not extract casing and got stuck half way out...

Gun; savage 10 fcp .308 Brass; FGMM I full length resize the brass, trim the cases to length and the reload, after 3 or 4 reloads the cases will stick in chamber cannot remove with bolt. OAL is 2.80 if I goto 2.83 bullet gets stuck in lands, and will pull out of case upon extraction. Load...

Need some help identifying this rifle. It's a gew 98 no other markings except on 22 bolt #48. Top of receiver where the numbers should be have been filled in and reworked looks like factory rework. Still has 8mm receiver but has a 22 receiver inserted into stock receiver. Has 22 cal sleeve...

Got elevation set for 100 zero and noticed that my elevation knob was almost as far down as it could go. Just wondering if anyone else has seen this on there setup. rifle Savage 10fcp 5r 308 egw 20moa base vortex 6-24x50 175smk federal brass 44.5 gr varget

Got the info I need thanks. Post removed

The attached pictures are of the ladder test I conducted on my Savage 10FCP this weekend. I plan on runnig the test agian just to double check results. 175smk's FGMM brass Winchester primers Varget powder 2.80 oal 300 yds Here's a closer look!!! I think 44.6 will be my load

Hope someone can help, I was told by a friend that one of the hide members are adapting extended mags 10 round for the savage rifles. Does anyone know who this might be? Did a search but I probabley did not word it right. Thanks

Does anyone have any idea how well the 5R barrels hold up compared to the button rifled barrels?

I have a 10FP savage with internal magazine, would like to upgrade to a stock with an external magazine. The rifle is a centered feed, and I'm looking for the best options. Still am using original stock and want to upgrade to a tactical or varment style.

I need a little advise. I have a savage 10fp in 308. Now this rifle has an internal magazine, I did not consider this when I bought the rifle. Looking to upgrade to an external mag. But have a question about rifling choices. Is the 5r rifling much more accurate than the standard rifling. My...

I have a savage 10fp in 308, hand loads are 175smk on fgmm cases, using 44.5 grains varget. oal 2.8. Scope is a vortex viper pst 6-24x50. Question is can accuracy change at longer ranges do to load. I get sub moa at 100 yards but at 500 and 1000 my patterns seem to be all over the place. I know...

Just thought I'd pass this on to any newbe's to long range shooting. I have a savage 10fp with a vortex viper 6-24x50 in 308, when I mounted the bypod I mounted it on the front loop. This was fine at 100 yards 5 shot groups under .500" at three hundred yards I found that all my shots were going...

Noob question. Every time I fire my 308 from a bench the recoil throws the rifle off to the right. I'm using a bypod anda bag at the rear. I have no problem hitting the target, but have to re sight to take second shot. I've tried holding firmly and loosened up my grip no change. Any ideas on...

I've been searching this forum and have seen posts about the proper amount of torque when mounting a scope. I'm currently waiting on a viper pst 6-24x50 from liberty optics. Is the correct torque listed in the owners manual, and if not would be grateful for any help. I have not picked out rings...

I had a friend send me a link to m4carbine forum where one of the distributors is saying that parts and ammo are becoming hard to get due to the 2012 elections coming up. Has anyone heard of this?

Anyone know what part of japan the lenses for the vortex scopes are made? Just wondering if there's going to be another delay on the psts