Search results

Special Texas run of the odinworks 15” key mod forend. Cerakoted burnt bronze, used for sure. All mounting hardware included. $sold I can usually ship Thursday through Saturday due to work…

Untouched. 8 twist $750 shipped I can usually ship Thursday through Saturday due to work…

x2 AXMC/SR .338 mags. They appear unused, light scuffs from bags/box $125 each shipped Proof steel .338LM 26” 9.4 twist. 100rds fired $575SOLD trades: AXSR Magnum bolt AXSR .308 mags AXSR/MC barrels, 308,6xc,260, 300/338 NM I can usually only ship on Thursday through Saturday due to work…

ADM standard 35mmSOLD ADM cantilevered 34MM both are 0 Moa $140 SOLD in great shape, may include dog hair… I can usually only ship Thursday- Saturday due to work.

Looking for M30 barrels in .308, .260, and 6CX.

Larue STOMP Mount, 34MM 20 moa. Little use, a few dings in the finish. When the NOD mount is off, you could mount a radius/raptar on the 12 o’clock rail… $traded trades: 34/35mm Spuhr mounts raptor rails spuhr data card holders

Manners TF4A OD green for Remington 700, pillar bedded and lug area bedded. Badger M5 bottom metal, Tubb 4 way butt, short arca rail, 2 flush cups on the left side. A few dings in the paint from match use. $1250 shipped conus feel free to make offers trades: fast twist 1.35” blanks in 6mm...

SMALL SHANK SAVAGE shilen 6XC prefit, bull, 1-7, 25”, 5/8x24, less than 300 rds through(it’s an absolute hammer)-$300 2 ultimatum barrel nuts- $50 each none of the finishes are perfect- light dings and scuffs from bags, etc… all prices shipped CONUS Make offers only trades I’m looking for are...

Looking for one. Not picky on color. cash or partial trade of 3-27 S&B H37, pantone, in a spuhr mount.

FS: LH Kelby repeater .338 action with integral 33MOA base. The bolt handle has been repaired by Kelby previousy. On action is a a 31" 7 twist Hawkhill MTU (5/8x24) .338 Norma fitted by Matt Parry (500rds fired) Also a Bartlein 22" gain twist 9.7-9 (5/8x24) .338 Norma fitted by Matt Parry...

All Prices shipped CONUS: GDI 34mm 0MOA, one small knick on the rear cap near the screw hole- $300 ( will trade for a 35mm 1.5 Spuhr) Larue LT204 Cantilever, rings are new in bag, mount was used once with no damage - $125 SOLD Badger 34mm Unimount- 1.35" 0MOA used once- $150SOLD Paypal...

FS: Gently used Gen 3 PVS 9. Comes with original mount. Has an aluminium Throw lever (larue) Clip on mount. This was made as a one off for a 1.5" ring height and up to a 56mm objective. You can check out the NV forum reports on the clarity of these- it is impressive. For my Purposes, i have...

Mounted, Never fired. This combo was over $1300 new (with shipping/VAT/exchange rate/wire) The Bottom Metal trigger area has been professionally opened up to accept double set triggers. Comes with 2 mag latches, action screws, 1 Fitted 5 rd mag and spacers. Not planning on separating...

This was my lunch time project for a week or so. It started out as a pile of parts in a shoebox, a 1940 marked Turkish mauser without a single matching number. It RC tested at a wopping 21 RC- So i decided to stay away from any high pressure round. A friend showed me the Rhineland arms...

i have been using a LR Accuracy Sniper's Choice 2 (SC2) bipod for about the last three months. i featured it in my review of the XLR chassis stock for my Robar RC50. As promised in that review, i will now attempt to review the SC2. i am going to do my best at giving this piece of equipment a...

i bought a used Robar RC50 in 2004 after selling my Barrett 99. The Barrett was tough and accurate. However, it was less than aesthetically pleasing. i felt that the trigger was decent, but not great. The area above the ejection port, being bare metal, was not a great place for a cheek weld. So...

Does anyone have the correct dimensions for the OPS inc collar step on the mk12 on digits? A drawing would be great. Thanks in advance