Search results

I have LMT MWS guns and my spare barrels have turned into guns. I will admit it was when spare parts were more plentiful but dont trust yourself. Just buy another upper if you wanna save a few bucks. PB

That is a 556 gun correct? Very cool set up either way. PB

That ammo shot 1.5 to 2 MOA and was .60 a round Back in the day. Sometimes MOA if you got lucky. It shot very well, also the big bonus is the brass is excellent. We weighed it and it was very consistent and holds up well for reloads. We even used it for bolt gun ammo reloads. We shot it to 1k...

I’ve gone so far down this rabbit hole and climbed back out so many times. Most cans are more similar than different. I said most but now you do have the flow through equation. If you do your research and obviously you are, once you buy your can you will be good to go. Food for thought. Most...

I have an Sig 338 can and I run it on my 300WM bolt gun and would run it on a 300 gasser if I had one. I like to run over bored cans on gassers to ( and bolts) to reduce back pressure and reduce chance of end cap strike. I’ve never noticed cans being louder. 9/45 6.5/30cal etc. PB

BCM is top shelf BCG. I wouldn’t worry about the pitting unless it was horrible. If you run it and it causes problems, replace it otherwise maybe rock on and keep the BCM handy. Or just replace the bolt with BCM bolt. PB

I have owned both and I think I have the LW version now. I noticed no difference between the two to the point I am not sure I know the difference. I bought the FDE slick side LW gun if my memory serves me. Then bought a 20 inch SS barrel trying to get more velocity but gained very little. I...

I know there was a bunch of hype with the 6.5CM 13.5's but those barrels are unobtainable. I'd like load a mag of 120 grainers and let them rip upright moving forward. I shoot a fair amount of 155TMK's with good success but that is as light in 308 for handholds. 147 MEN has been shot quite a...

Happiness is a warm 16CL MWS barrel, so yes 100%. I wish I had a 13.5 just to play with but 16 is the real deal. I dont want to give up that much velocity. PB

Fuck yes, I bought a 14.5 with FSP. DD Upper G-SD LMT PB

I have DD, Geissele SD and LMT. All three are great guns (ut755ln) Freudian LMT slip is solid advise. LMT would be my goto. I have no experience with LWRC so there is no opinion. If you want to look for a LMT take a peak at V1Tactical and Titan Defense because there are hard to source...

I really thought we were safe with these barrels but its great to hear someone took one out to go bang bang with solid results. Thanks for the reply. PB

Who makes that stock? I like my stock OK but for some reason I don't like the recoil impulse which is admittlingly a weird thing to say on a bolt gun. Not sure if its the 2 stage trigger or what, but its not the same as my REM 700 5R. It's just odd to me. And I have shot the shit out of the...

Our first load that we shot this was hotter, but our last batch was 2,755 FPS. If my poor memory serves me, we were trashing brass and was maybe 100 FPS faster. I almost fucked up my bolt with that load. And yes the 88 ELD load stabilized and was sub-MOA. My 1/9 Rem 700 stabilized 80 grain...

If you want to experiment with other rail pieces these screws are the replacement screws. I just bought a couple of spare rails to have on stash since I have a couple uppers. But these are the screws. Before I found the spare rail pieces, I wondered if there were other rails I could...

Not yet. PBV

Play between upper/lower is a non issue for me. I'm talking about the barrel shifting forward and backwards after tightening down properly. I doubt its significant but still curious. PB

Hey Fellas, I have a 16CL MWS that shoots great. I have a slick side upper that takes that rail segments and was messing with those and noticed a very slight amount of play to/fro on my barrel. No side to side but barely just a click. On my other two uppers I do not have this, anyone noticed...

I have a 16inch CL barrel and bought a 20 SS barrel hoping to get a big velocity jump and got a very slim bump if I remember correctly. About 60-75 FPS and was hoping more, like double. I just started a thread on barrel lengths and velocity so maybe next trip out I try multiple loads and see...

We often discuss how much each inch of barrel will effect velocity, obviously there is more to it than just barrel length with twist and chambers etc. But here are some loads with comparisons and resulting delta's. I started with a handload 69 grain SMK load Tikka 2,934 FPS 5R , 2,827 FPS...