• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Search results

Search the forum Search Articles
  1. T

    Pet Loads with the ELD-VT Bullet?

    Two different Sig Cross rifles. One STX with 20” barrel, the other an HXT with 24” barrel. Velocities from the 24” barrel. Both rifles grouped the same load into 1/2”.
  2. T

    Pet Loads with the ELD-VT Bullet?

    100 gr 6.5mm ELD-VT Bolt Gun. 6.5 Creedmoor. StaBall Match. 42.2gr. Lapua SRP brass, CCI450 2.762” OAL 3065fps. SD 9
  3. T

    Accuracy International AT-XC

    M6
  4. T

    New Sig CROSS

    Not that I’m an expert, im not, but the velocity x weight must be 380000 or greater. 140s need to go 2715. 147s need to go 2585. You can decide what works best for you. Plus a pad for temperature, variations like es/sd, and the phase of the moon.
  5. T

    New Sig CROSS

    1. Looks like my STX with a 20” barrel gets 2700 fps with my 140 ELDM load and 2725 with my 130 TGK load. I looked it up, and this load ( 2700 fps x 140grs) in my STX will not make NRL power factor. Of note, the HXT with the 24” barrel does make power factor. 2800fps x 140gr. 2. Yes...
  6. T

    SOLD Harrell’s Precision Micrometer Powder Measure 0-100gr plus Lapua Brass

    Wow. That was a deal right there.
  7. T

    223 Ackley Improved

    The photo of the 88ELDM target has all the load data, including OAL. Yes. In Tikka 223CTR and MDT 223 mags.
  8. T

    223 Ackley Improved

    OAL around 2.450”
  9. T

    New Sig CROSS

    I think the rings are MDT medium height
  10. T

    New Sig CROSS

    I like the ARCA fore end a lot!
  11. T

    New Sig CROSS

    My bad, I misspelled HXT. This is where I first heard about the HXT: https://www.vikingtactics.com/sig-cross-hxt/ The STX has the full length Pic rail on the hand guard. The STX is black, the HXT is grey. The STX has an Sig taper muzzle device, the HXT comes with the ring that allows a...
  12. T

    TRG appreciation thread - Part III

    OK, I'll play. TRG-22 with laminated stock. Baltic birch core, with the aluminum backbone installed. Zebrawood flanks. Brazilian Cherry cheekpiece. 6.5 Creed. TRG-22 in a KRG W3 folder with ARCA Spigot. Walnut Cheekpiece and bag rider. 6.5 Creed. Both are very accurate.
  13. T

    New Sig CROSS

    Sig HTX is a deal. Has the ARCA fore end that I like, and most of the same features as the STX. But the barrel is 24". Lacks the STX/PRS safety and fat bolt knob. Both of which can be added. Feels like the PRS version without the steel parts and weight. Mine weighs 10.8 lbs with scope...
  14. T

    New Sig CROSS

    Sig HTX 6.5 Creed Sig STX 6.5 Creed Same load. 42.8gr H4350. Lapua SRP brass. CCI-450. Hornady 140 ELDM. Factory barrels. Zeiss scopes.
  15. T

    Coup De Grâce 223 action experiences?

    I think part of the fundamental problem here is that a CDG has a larger diameter bolt body (not bolt head) then a traditional 2-lug Remington clone or others. A magazine seated with the feed lips close to the bolt body cannot get as high in the CDG action (as close to action center line) as...
  16. T

    Will suppressor cover sliding forward act as crown or mess with groups?

    Silicone dish mat. Some Gorilla tape and some camo tape. I can get 2 covers from a $12 mat. Yes, I’m a cheap-ass. But my AG covers slide around too much. Depending on how tight you make them (so to speak) they don’t slide around at all. Very temperature resistant, and vented with ridges.
  17. T

    Stock filler

    Have you tried duct seal? https://www.homedepot.com/p/Gardner-Bender-1-lb-Plug-Duct-Seal-Compound-DS-110/100212441 I use it, I’ve tried the bags to separate the putty from the stock. I’ve also put lead shot in it to increase weight and dampen more vibration. YMMV.
  18. T

    223 Ackley Improved

    Around 2.450”
  19. T

    Why are we not talking about the devastation in Western NC, TN, and other places?

    Has anyone set up a GiveSendGo for donations to the families in need?
  20. T

    223 Ackley Improved

    I’ve got a uni-throater in 223 and 6mm. I cut to fit my needs. I recommend having them hand throat it. Measure your magazines, figure out your desired OAL. Measure your ogive at that desired OAL, and that will give you a rough idea of what your freebore should be to support your desired ogive...
Top Bottom
Back
Home
Forums
Merch
Alerts