Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Watch Out for Scammers!
We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!
Bill- I'm running a Nightforce comp on my 6mmCreedmoor F rifle. The scope is sitting on a 20 MOA rail and nestled in Nightforce rings. I have no problem getting a zero for 100 or 1000. Scores with this set up are at top end of Master classification. This was my first season shooting F-class...
If you hate the length on 10 round 223 mags as I do, you can also make a "hybrid" 5 shot 223 mag using Accurate mag 223 inner parts. I used a scuffed up AI 5 round 308 mag for the prototype. Drill the spot welds and remove the reinforcement/spacer from the front -inside of the mag Pull the...
I pre-clean before blasting with an aerosol carb/choke cleaner. I blast with barrel out of action because it seems easier to me to get all the abrasive out of all the nooks and crannies that way. I plug/tape/mask off places I don't want blasted or coated. I reassemble after blasting then go to...
Chad- I've used that trick with Devcon plastic steel on seating dies and sizer dies for cast bullets for years. I used a drill bit for the over sized hole then scratched up the interior for more grab with the bedding compound. Never had one not stay in place.
I just got my new TBAS from Straight Shot a week ago. Yes it's pricey but it is a wonderful piece of kit. It does stick out further from the spindle than the 4 jaw I've been running but I only use an outboard spider to keep the outer end of the barrel captured.
Irish....FYI Back in the late 90's early 2000's I shot the 900B exclusively and still have a pretty good stash reserved for special occasions. During that time frame I was shooting schuetzen at Nationals in Raton along side Lones Wigger. If that name doesn't ring any bells run a search. Lones...
Derrick The replies above are correct to my knowledge about degree of polish....about 320 is perfect and I've found 320 done by hand is way better than 320 on a buffer. The binders/grease in buffing compound are your enemy. The time you allow the chemical to work can also lead to rougher...
I am almost to the end of my Form 4 wait and have a TBAC can awating pick up in Cheyenne. I can't say enough about the customer service there. As for your thread issue.....I install muzzle devices, not as many per year as some of the bigger shops, but quite a few. I use an old school manual...
on the back of the part of the money order you should have kept...."present this receipt and file a claim for a refund at your Post Office. An Inquiry form 6401 may be filled out at any time for a fee. A replacement will not be issued until 60 days after the money order purchase date, provided...
my chamber is cut with a standard PTG 6.5CM reamer. I run Berger 140 VLDs . My gun regularly shoots under half MOA with lots of groups in the 0.3-0.4 MOA range. My OAL is 2.85" for mag fed and 2.87" for single load. Both lengths shoot great and under most conditions don't require dope changes...
I've built 3-4 rifles around the RR prefix actions only from Brownell's. They have a nice blue finish with out the heavy blast underneath. I have only "trued"...not blueprinted, lugs lapped, face squared- so I didn't run into extraction cam issues. These builds have all shot very well...half...
Mikee....I think you've hit the nail on the head. I'm not going to spend the $8500 to get this lathe bought and shipped then proceed to rip its guts out. I think a rotary converter is the way to go on THIS lathe. I can manage the hook up for the rotary. Up and running with no undue...
Lee....I'm a gunsmith...not an electrician! What re-wiring of the motor would be needed? I assume you're talking about making a home made phase converter out of the electric motor? Again...I get lost past " plug it into the wall socket". The store bought phase converter Grizzly mates with this...
Jon and Red..........many thanks for the info. Its nice to ask a question here and get useful feedback vs. the too often sarcasm and BS. I talked with the guys at VFDs.com and they were very patient and very helpful. The single to 3 phase system is a viable alternate to a phase converter plus...