Search results

I need someone to complete a rebarrel job on a POF 223. I will have the gun back in my hands soon. this is a piston gun. Please PM me with any questions or details.

Strange question I know, but I have never talked to anyone who first hand had actually witnessed one.

I have been cleaning after every session but I see some guys are going hundreds of rounds before cleaning.

I was asked by another member to share this FWIW. I have been using my CM like this ever since I got it and never really thought much about it. I noticed that it seemed to choke on extruded powders and overthrow. I found the McDicks straw mod online but that didn't seem sufficient as it was...

I own quite a few Premier scopes and for the first time I had to have some work done. Just a little oil on the ocular not even really noticeable except with a bright light shining into the scope from the rear. But being the perfectionist I am I wanted it cleaned. I contacted Trevor at Armament...

After doing a close bit of eyeballing on the optics market "looking for my next scope" I have found some interesting things and wanted to see if others could fill in some more info on this. So let's say a company like Bushnell, SWFA, March, Nightforce (all L.O.W) want to bring a new optical...

I wanted some input on this... I have heard this so many times "Which scope is better ____ or ____?" And the conversation usually goes on post after post about how this scope or that looks sooo much better and clearer and "____ brand done!" What I would like to know is how much of that is...

I was told that I had to full length size when I am prepping brass for a gas gun by several guys. If I am prepping brass that is and will only be shot out of the same rifle why can't I just NS?? I did NS some of the brass from that rifle and it feeds and ejects just fine. I can't see how it...

I have been using a cheap Lyman vibe tumbler for awhile and realized that I use it quite a bit so I have started looking at SS media rotary tumbling. My question here is I am not sure if I should go for a full sized 15lb or a smaller one. I tend not to have batches over 300 cases. Should I go...

Well I think I have finally narrowed my choices down to these 2 and I kind of like both equally but for different reasons. Could I hear from some of you with experience with either or. I guess some 100y accuracy reports would say a lot as I searched pretty hard and couldn't find much..

I am looking to start a build on a high end upper, where can I find a good quality, coated, stripped or partially built upper? ar15 of course

Trying to make my final decision before purchase what would the pros and cons be for an 18" vs a 16" barrel??

I was thinking about buying an AR-15 in the higher end and $2000 ought to buy something pretty nice. It would have to be a piston gun, 223 and capable of 1moa or better. Any suggestions?

What is a decent price for new, unfired, primed LC match brass??

I am in a tough pinch guys, getting back into shooting and had to resort to buying a powder I'm not familiar with. The burn chart shows it right in the sweet spot for those calibers. I reload 308 using 168 and 175 SMK's and 223 using 68 and 77 SMK's Can anybody help me out on load data for these?

I have a really sweet customized rifle built off of a tricked out Rem 700 SA with a hand bround PTG bolt. The bolt body is polished stainless just as it came from PTG. The bolt lift is smooth as silk but when I have the bolt fully open + retracted and I go to close it I get a little resistance...

I could've swore I remember there used to be a section on 2nd discussion. Was it removed or was I dreaming.

When using rings that have 6 screws on one and 4 on the other, which goes where or does it matter. Does the 6 screw ring go in front or back???

I am not at all up to speed on what all is available and what kind of pricing I should spend for each different gun. I do know I would like to have a piston driven and not a gas impingement system. Can some of you guys tell me some good options for $2500 or less??

I have been looking at barrels for a 308 build to shoot lighter bullets and I am seeing there are .300/.308 and then there are .299/.300 so what is the deal with this? What should I buy or what issues can I be faced with. Common sense would say jamming a .30 cal bullet down a .299 hole might...