Search results
-
Reloading Equipment WTS 7MM Mag Supplies Berger 195 Elite Hunters & Nosler Brass
PM sent on the 195s- T2hunter
- Post #2
- Forum: Buy - Sell - Trade
-
-
-
-
-
Ladder Test- Hide Input wanted on the next step
If we’re taking opinions on this too. Here’s my .02:) 3 shot groups If it ain’t going to do it in 3 why waste the others.... Lands or jam.005 .01 .02 .03 .04 And so on- T2hunter
- Post #50
- Forum: Reloading Depot
-
Ladder Test- Hide Input wanted on the next step
38.8, run seating depth test. would anyone try a different primmer? just curious :rolleyes:- T2hunter
- Post #41
- Forum: Reloading Depot
-
Gunsmithing UNF Thread Specs?
There you go! Wrong again :poop: But Yah, after reading this, and doing some online research. I found that there are UK cans for .22s in 1/2 x20 tpi threading- T2hunter
- Post #11
- Forum: The Armory
-
Gunsmithing UNF Thread Specs?
I would probably say your looking for the 1/2-28 thread end though, If it’s for a suppresser? I’ve never seen one threaded for the 1/2-20 UNF thread But I’ve been wrong before:rolleyes:- T2hunter
- Post #4
- Forum: The Armory
-
Gunsmithing UNF Thread Specs?
No its not the same thread 1/2-20 is UNF Unified National Fine thread 1/2-28 is UNEF Unified National Extra Fine Screw Thread Hope this helps;)- T2hunter
- Post #2
- Forum: The Armory
-
Load development with virgin brass?
Depends on how much brass you have, or how much you plan on shooting the gun I’d say. On my 338L I ran 100 cases thru the gun doing fire forming First though, All cases ran thru Sinclair carbide mandrel die I Check with pin Hole gauges to inspect how tight the necks are and aim for (-.002 to...- T2hunter
- Post #41
- Forum: Reloading Depot
-
Load development with virgin brass?
https://www.sinclairintl.com/reloading-equipment/case-preparation/neck-turning/turning-expander-mandrels/generation-ii-expander-dies-prod38807.- T2hunter
- Post #17
- Forum: Reloading Depot
-
Load development with virgin brass?
Did load dev on virgin brass when I first got my Lapua Didn’t seem to matter to much Have to start somewhere I’d say Ended up going with 89.3gr retumbo 300gr smk @2720fps Hope this helps- T2hunter
- Post #6
- Forum: Reloading Depot
-
My daughter’s latest drawing.
Simply Amazing! Your Daughter must Have Eyes of a Eagle!.... To get the fine detail in the drawing , Only she could see her imperfections, and the rest of us are Like WOW!!! Talent Yep! and then Some....- T2hunter
- Post #66
- Forum: The Bear Pit
-
Precision Rifles.....show em!!
- T2hunter
- Post #757
- Forum: Bolt Action Rifles
-
which primers for Lapua 6.5CM?
Im using CCI-BR4s with varget in a 6.5x47 seems gtg I have 450 also going to try out as well my bolt from surgeon has the small firing pin When built- T2hunter
- Post #10
- Forum: Reloading Depot
-
Photos Picture test thread
- T2hunter
- Post #25
- Forum: The Bear Pit
-
-
Gunsmithing Bedding
I've done about 10 guns With Devcon 10110 All but one turned out really good! The one that didn't I Forgot to put the kiwi release agent on the action bolts and found out the next morning what a bitch it was to get apart! Ended up having to mill the bolts out on the stock But All turned out ok...- T2hunter
- Post #3
- Forum: The Armory
-
Precision Rifles.....show em!!
Sent from my iPhone using Tapatalk- T2hunter
- Post #2
- Forum: Bolt Action Rifles
