Search results

I'm gonna start a project (DIY Gun Oven), and was wondering if any one has stripped down and used a simple Toaster oven for the heater and fan. Criagslist has them for around 10-20bucks I Saw a couple guys on the hide using hot plates and dual hot plates, seemed to be simple. I'm planning on...

OK. I have the .420 insert, but the Hornady chart didn't show the that, so I wasn't sure. .33 made sense, but my 284 was like close to 278ish, so I didn't know if there was some special magic number. Thanks for the help.

Can anyone help out? I looking for the Dimensions of a 338LM headspace gauge and the bullet comparator....I Don't think Hornady Makes the Headspace gauge for this round. Not sure if the bullet comparartor for checking a 338LM is .338.....my other ones dont match up so I'm thinking its some...

So I'm wondering what makes a barrel burner cartridge? For an example the 6.5 wsm everyone says is a Barrel burner, gets maybe 500rounds, before you lose accuracy...most of the time these guys are pushin fast bullets around 3300-3400..... So would you gain barrel life by slowing down the bullet...

If your using a VLD style bullet, then try this. Redding Competition Standard Length VLD Seater Stems | Sinclair Intl I had the same problem because the standard stem wasn't long enough for the Bergers.

This came up in a conversation because i have always been told that a scope should always be pushed forward against the rail, i was thinking the Lug would be the same.

The stock I have has a larger recoil lug opening than my Badger recoil lug is....so there is little wiggle room in Front/Back, Both sides, and the bottom...should the recoil be pushed to the front of the lug area or tight to the face of the Alum bedding Block? or does it matter...i was reading...

Getting close to finishing my lightweight hunting rifle in Rem 700 6.5/270wsm and I figure I would update..should have some photos in a week or so Rem 700 SA Trued Action only .872lbs Rem 700 Stock Mag Bolt, w/Bolt Knob .734lbs Trigger...

Had the same problem with my 7rem mag...or a similar problem....if it only happens after you fire the round on "once fired brass" try this.. Belted Magnum Collet Resizing Die....http://www.larrywillis.com/... Haven't had the problem since.....and I krylon painted my bolt several times...its a...

Rattle can has held up for me on several rifles(4)......make sure its clean before you paint...of course.....another good tip is heat the (paint) can up to about 90 degrees for 5 minutes or so(boiled water works the best)...apply multiply thins coats for best results.

Re: Chrome Moly Steel or Stainless steel Barrel WOW-BobD thanks for the input! i think i will wait for Stainless, it seems easier. Thank you

Which is better for Barrels; Chrome Moly Steel or stainless steel..I don't really know the difference and was looking for help on picking a new barrel. thanks

Re: R700 7RM 168LRX LOAD DATA Perfect..Thanks for the help...

Re: Rifle components Weight I would also like some input on being to light....I remember my last gunsmith talking about a balance in the gun....not too heavy barrel on a light stock....etc... is there a rule of thumb for this?

I'm looking to build a light weight 600-800 yard rifle for mostly hunting and some fun Tactical shooting. trying to determine the weight range and what to look for. Its gonna be a 6.5 WSM....what should I expect for weights of the different components. trying to be around 10-11lbs Here is what I...

Re: R700 7RM 168LRX LOAD DATA Bump.bump

Anybody have starting load data for 7Rm,168LRX and H4831sc looking to find a all copper load. I'm using 65.5grns of H4831sc with the Berger hunting VLDs.... would it be safe to start around 62 and work up? not sure if there is a difference with the two different bullets? Thanks for any input.

Re: 7mm Rem Mag vs black bear?? Feed it with some 180vlds, no problem! you would be fine to 6-800yards

Re: Coyote hunting caliber question 204 is a great round for killing yotes to around 350-400. have about 10-15 down under my 204 VTR. I love it

Re: sucessfull mountain lion hunt Nice Kitty Cat