• Watch Out for Scammers!

    We've now added a color code for all accounts. Orange accounts are new members, Blue are full members, and Green are Supporters. If you get a message about a sale from an orange account, make sure you pay attention before sending any money!

Search results

Search the forum Search Articles
  1. M

    Gunsmithing Which torque screwdriver to get

    Fat wrench, easy to use...
  2. M

    Hello from NC

    Welcome to the hide and thank you for your service
  3. M

    .308 bolt difficult to close

    I had this problem once with a reload because the primer wasn't fully fully seated.
  4. M

    Rifle Case/Bag Recommendation Needed

    I have the voodoo bag for my 26 inch r 700; aics chassis, scope, etc, and it carries a little nose down even with the bipod off. If I grab the handles at the very front it seem to level out. It's very well made, zipper is rugged and lots of pockets.
  5. M

    AR triggers

    Just installed a SSA-E, on my DPMS 308, it's a nice improvement.
  6. M

    Big Hey Ya'll from Georgia

    Welcome
  7. M

    Winchester primers vs. CCI-200 primers as indicator of pressure in 308/7.62

    There was a period not too long ago, where they were only ones I could find. (At the local Big 5, no less). And I have experienced a few FTF with these primers. I've reloaded with both CCI and Federal with less problems.
  8. M

    Horrible accuracy with custom SR-25. Help!

    I realize this is not my circus, not my monkeys, but I (also) have a new gas gun with teething problems. So I appreciate all the suggestions being offered here. Thanks , and to the OP, good luck, hope you solve your problem.
  9. M

    Another reason not to send your Remington in for recall.

    Hope you get in back promptly, And by all means, get a Timney for it.
  10. M

    Overtorquers Anonymous

    Picked up a "fat wrench" from midway. Very user friendly
  11. M

    DPMS SASS with JP trigger

    Update. I surrendered to the SSA-E. Groups tighter up, and it seems to run a little smother. Thanks for the suggestion
  12. M

    Test Results: Accuracy/Precision of Annealed, Non-Annealed, COAL to Magazine Length and ti

    More good info Thanks guys
  13. M

    Be honest who would miss CA

    all righty then...moving along
  14. M

    Please school me on short barrel .308's

    Interesting read, thanks for the heads up
  15. M

    What reloading equipment to purchase

    Ok, this is/was my journey into reloading. As far as a press goes, I started reloading .45acp with a Lee Classic Turret and Lee dies, after I gained enough confidence I moved into reloading the 9mm. The 9mm cartridge is a little more finicky then the .45acp. I also started reloading 223 on the...
  16. M

    Gap 10

    I purchased a dpms sass about a month ago in Oakley. Ca compliant with bullet button
  17. M

    Rifle Camo, why? (Can of worms)

    Some of you guys are just too funny ....off to buy some paint ...
  18. M

    Bullet drop table for .308?

    check the back of a box of FGMM 168smk. there is a chart that lists velocity at the muzzle as 2650 fps energy 2620 ft/lbs. Average range 0 @ 100yds, -4.3@ 200yds, -15.3 @ 300yds. (sights 1.5 inches above bore line.) hope this helps
  19. M

    Working up a load with IMR4064---Check my math.

    I agree, my low node was at 41.7 and another at 42.6g. YMMV
  20. M

    Cost v. Benefit of Reloading .308

    This, I started reloading .45acp, so I could shoot more. So, reloading 223/308, was a natural progression for me. It's a fun part of the hobby, but I'm retired and have the time for it. Plus it's adds a little more satisfaction to the shooting experience. Enjoy
Top Bottom
Back