Search results

Looking to buy a middle-upper range LPVO. Tango 6, Vortex Razor Gen II, Etc.... Text/Call anytime: 620-687-5680 Email: [email protected]

WTB a Vortex AMG with MOA reticle/adjustments. Text/Call at 620-687-5680 or email at [email protected]

Ok team, i’ve been doing some load development. I conducted an OCW test and landed with 71gr H4831sc behind a 200gr Berger hybrid. Today I tested the loads stability. I shot x2 70.5gr, x4 71, x2 71.5gr (top 3 targets in the picture). The wind was a full value 4-10mph variable. It seems the load...

Does anyone know what manners mini chassis BDL LA max COAL is?

I just got back from the range and I have a relatively good problem to have. I’m not sure where my OCW node is out of the 6 loads I shot - but most charge weights shot fairly tight groups. I used new Lapua brass, 185gr Bergers .012 off the lands, CCI BR2 primers, and IMR 4451 at: 54.0, 54.4...

All, I just got back from the range and I have a relatively good problem to have. I’m not sure where my OCW node is out of the 6 loads I shot - but most charge weights shot fairly tight groups. I used new Lapua brass, 185gr Bergers .012 off the lands, CCI BR2 primers, and IMR 4451 at: 54.0...

Ok so Noslers data has these cartridges with h2o case capacities significantly lower than other numbers being thrown around the internet. Can anyone shed light on what the real numbers are for any if these cartridges or just any info in general to point me in the right direction? Thanks.

Ok so is it possible to have 300 SAUM in a SA and shoot either berger 168gr hybrids, 175gr, or 185gr VLD's (at mag length) without cramping powder space too much? The SAUM, as I'm sure you all know, is shorter overall than the WSM and has a longer neck, both characteristics will aid in this goal...

Ok so most load data has CFE-223 topping velocity charts, but that is with a 24" barrel. If my logic is sound then for a carbine/M16 length of barrel then out of the .223 data for light projectiles, I want to pick the one that is near top in velocity but has the fastest burn rate so that the...

Ok so all I can find on the internet is 6.5 Grendel data for a 24" barrel. Does anyone have some verified data for a 16, 18, or 20" barrel? Doesn't matter what projectile weight, the more variety listed, the better

Ok so I have a Harrell Powder dropper and it is absoloutely fantastic for everything till about H4350. Anything slower than that like H4831sc and it WILL NOT throw consistently. This is just me being lazy, but are there any powder droppers that will throw magnum powders reliably so that you...

Ok so I have a 280 AI that I have developed some fantastic loads for, but I continually puncture primers. My original load was 60.1gr H4831sc 168gr bergers, and CCI 200's, and there were no pressure signs except I kept puncturing primers. I sent my bolt in and had it bushed, still getting some...

Does rechambering/setting back a barrel give it full life again or is the life of this "new" chamber/throat reduced from the original?

Just got my new 280 AI from Score High in, outstabding craftsmanship. Went out and did an OCW test today and did max load tests for H4831sc, H1000, and Retumbo. Retumbo won out in velocity with 168gr Berger VLD (hunting). They were seated about .010 off the lands for the pressure test and OCW...

My question is in regards to barrel fouling and OCW/ladder results. On Mr. Newberry's website it says to use a couple foulers on a clean barrel, perform the test, and then you may have to clean the barrel between 20-25 shots otherwise accuracy might start getting blown. There are many barrel...

Ok so I'm thinking about parting out a rifle I have. It was a .260 built on a 700 LA. My question is, can this barrel be put on a SA without modification (will it just screw on)? The original action was not trued so it's original receiver threading. Thanks

Ok so I have a rifle with a manner t4a, bedded and everything. Right now it has BDL bottom metal, if I wanted to switch to a DBM system, will that screw the bedding up? Will I have to have new pillars put in, ground down, will the bedding itself be out of spec? I understand some inletting will...

Ok so I have a 280 AI on the way from score high, I have a redding type s 3 die set, bushing neck sizer, micrometer seater and a body die (body only). Lately I'm starting to prescribe to the whole FL resize every time. Should I sell these dies and send a fire formed case and have custom dies...

Just wanted to know where people were seating 7mm 168gr Berger VLD Huntings off the lands, going to be on a 280 AI but 7mm mag shooters or anyone shooting these projectiles input is welcome. Thanks!

So I am getting in a 280 AI from Score High here pretty soon, I'll be using nosler brass CCI 200's and 168gr Bergers. The rifle is a blueprinted 700, 26" 1:9 Bartlein M24 5r, manner T4A stock, Timney trigger, NF scope base, vortex razor 5-20 w/ seekins rings, and etc. should be a great rig. My...