The 139 Scenars are the shit in my gun as well.
42.9 grains of H4350 .015" off the lands.
2855 fps, very low SD/ES
42.9 grains of H4350 .015" off the lands.
2855 fps, very low SD/ES
- Thread starter Sportin Wood
- Start date
What is your COAL with this load, please?
Hi guys,
My old load with the 140 Hybrids stopped grouping well for me. Load 42.9 H4350/ 2.86"
1. Should I seat them longer until accuracy comes back?
2. Increase the charge?
3. Or both?
My 139's Scenars still shoot super accurate with the same barrel so it's not toast yet. The barrel only has about 1700 rds.
My old load with the 140 Hybrids stopped grouping well for me. Load 42.9 H4350/ 2.86"
1. Should I seat them longer until accuracy comes back?
2. Increase the charge?
3. Or both?
My 139's Scenars still shoot super accurate with the same barrel so it's not toast yet. The barrel only has about 1700 rds.
42.6 h4350. 140 vld at 2.140 to ogive. Fgm210m. 2814 fps. Gap Crusader. 890 yards
Where did you get your info to start loading with the Lapua 139 Scenar? I can't find a reloading manual online or their website. I have some of these bullets on the way and really want to get some loads started. Thanks!
I started with 140 gr bullet suggestions in the book and worked up a load. He's got more in his then I do.
I'm having a heck of a time with my Berger 140 Hybrids. Would it be safe to say I could duplicate my powder charge used for load development for my Bergers and be ok?
Tikka action
Bartlein 1:8.5" twist Rem Varmint contour, 26" finish
JEC Brake
140 gr. A-max
H-4350
.024" jump to fit in the mag
42.4 gr
2810 fps average MV
ES 15
Left to right wind, 7 o'clock, 2-6 mph.
Had a flier 3" below the center of the group, but I'm gonna blame that on the mirage today.
Bartlein 1:8.5" twist Rem Varmint contour, 26" finish
JEC Brake
140 gr. A-max
H-4350
.024" jump to fit in the mag
42.4 gr
2810 fps average MV
ES 15
Left to right wind, 7 o'clock, 2-6 mph.
Had a flier 3" below the center of the group, but I'm gonna blame that on the mirage today.
i shoot 1000yd i.b.s. and my pet load for 6.5 creedmoor is 42.7 gr of h-4350 ,140berger vld seated .0010 off lands produce sub 4 in groups at 1000 and routinly sub 5 in groups. best is a 3.188 and 3.778 for record. no pressure sins, fed 210match primers. bartlein 5r @28 in long, bruce baer mbr stock , jewell hvr, nightforce benchrest 12x42 2dd recticle. got 1640 rounds documented and still shoots sub moa at 1000yds.
I just picked up my rifle !!!!! Cant wait to try it...lol
Sent from my SM-G900P using Tapatalk
Sent from my SM-G900P using Tapatalk
Started with a rem 700 sps varmint in 22-250, with hs precision stock, detachable mag. Very nice shooter but the barrel was worn.(I haad over 3k rds thru it) so a couple months ago I gave it to wild west gun for them to replace the barrel but in 6.5 creedmor cut to 26 inches, add a muzzle break , add a timney trigger and true the action. Im on my way to try it, its super windy but I just can't wait. I have only 36 rds but thats ok...lol.
Sent from my SM-G900P using Tapatalk
Tag
Yes sir. You'd be fine
I think i can safely speak with authority on the creedmoor. I shoot one in 1000yd i.b.s. And routinly shoot sub 5 in groups in competition with a best of 3.187 and 3.374.
My load is 42.7 gr h-4350 fed 210m 140 berger vld seated .010 off the lands- 28in bartlein 1:8 mcmillan mbr.n/f 12x42 i would spend the money now and handload to really show the potential of the great round- factory load shoot ok but if you really want to unlock accuracy...handload.
My load is 42.7 gr h-4350 fed 210m 140 berger vld seated .010 off the lands- 28in bartlein 1:8 mcmillan mbr.n/f 12x42 i would spend the money now and handload to really show the potential of the great round- factory load shoot ok but if you really want to unlock accuracy...handload.
Subscriping
I bought some 140 Hybrids to try, the first load I I tried looks pretty good off the Bench at 100 yards.
42.4 grains of RL 17. I think They are seated about .015 or .020 off the lands.
Hopefully they will work good off the 600 yard line.
Go to range report and exterior ballistics. I started a thread about the whole ordeal. It's the 140 Amax. The old Vs. the new
New 6.5 Creed load data thread on Scout. Help bring over the good data...
http://mbd.scout.com/mb.aspx?s=541&f=5533&t=13231164
http://mbd.scout.com/mb.aspx?s=541&f=5533&t=13231164
Went out again, still using varget (tgats what I have on hand) to ME it looks good at least to 600 yards (this is probably the best group I ever made at 600 but im kearning...lol)
100 yards , 35.8 gr varget, 27 inch shillen barrel
Here at 600 yards, 5 shoots.
From middle of the inpact (it may be the wrong way to check ?!!)
I tried a close up because we dont see the inpact that well.
Sent from my SM-G900P using Tapatalk
100 yards , 35.8 gr varget, 27 inch shillen barrel
Here at 600 yards, 5 shoots.
From middle of the inpact (it may be the wrong way to check ?!!)
I tried a close up because we dont see the inpact that well.
Sent from my SM-G900P using Tapatalk
Awesome!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Pressure signs
Any pressure signs with that load? Seem a little higher than normal.
Any pressure signs with that load? Seem a little higher than normal.
G
Guest
Guest
Thrust911
XFirst Sergeant
Rating: 3.4/5 this site
2180 posts this site
6.5 Creedmoor
10/07/2014 Last edited 10/15/2014 by Thrust911
Load data....Bring it on over.
Original thread: **6.5 Creedmoor Loads**
Mine:
42.0gr H4350
139gr Lapua Scenar
GM210M Primer
2.84" COAL
~2765FPS 26" Bartlein barrel
Single digit SD out of a GAP
Rate now:
LawnMM
XFirst Sergeant
Rating: 3.4/5 this site
3146 posts this site
Re: 6.5 Creedmoor
10/13/2014
Lets see...
44.1gr H4350
123gr Lapua Scenar
CCI BR2
2.800" COAL
2925fps 22" Krieger
Single Digit SD, 8 I believe
Going to experiment with Varget, H4350 puts a lot of pressure back through the port, this is an auto loader. I've got a few components I'm going to swap to try and delay the timing on the cycle but if that doesn't work I may switch powders in an effort to get the gun running less harshly. Its putting a beating on the brass right now and I believe most of the problem has to do with the timing, rather than excessive pressure. Its a shame, because its a really accurate load.
Rate now:
MarcusW
X79 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
208 posts this site
Re: 6.5 Creedmoor
10/14/2014
H4350 load - has been stable across 3 out of 4 lots
43.0gr H4350
140gr Berger VLD (Hunting version seems more accurate but Target is still 1/2 MOA)
GM210M Primer
.020" Jump
2820FPS 26" Bartlein barrel
H100V load - Faster but fouls barrel very quickly, leaves heavy soot on case necks. Only tried 1 lot
42.5gr H100V
140gr Berger VLD
G210M Primer
.020" Jump
2870FPS 26" Bartlein barrel
Rate now:
cecchino76XFirst Sergeant
Rating: 3.0/5 this site
1682 posts this site
Re: 6.5 Creedmoor
10/14/2014
Tag
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
10/16/2014
(1 vote)
GAP CRUSADER 1:8.25 Bartlein Bbl, MTU contour, 27"
42.6 H4350 , 140 vld at 2.140 to Ogive, fgm210m, hornady brass , gives me 2810 to 2820 fps.
42.7 H4350 with a 140 Hybrid at 2.124 to ogive with all of the same above gives me 2830 fps.
[IMG2=JSON]{"alt":" photo F74E78B6-CC69-4B91-86FE-0E1F05B08DFE_zpsqdrez2wn.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/F74E78B6-CC69-4B91-86FE-0E1F05B08DFE_zpsqdrez2wn.jpg"}[/IMG2]
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
10/16/2014 Last edited 10/16/2014 by DarksideSix
tag
Rate now:
drglockXGunny Sergeant
Rating: 3.2/5 this site
580 posts this site
Re: 6.5 Creedmoor
10/16/2014
41.4gr H4350
140gr Amax
GM 210M Primer
2.805 COAL
~2720 FPS 23" 8.5 Twist Bartlein
.20 MOA PCR Build
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
10/16/2014
136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
Rate now:
m118lr762X27 MONTHS
Premium Member
Corporal
Rating: 3.0/5 this site
82 posts this site
Re: 6.5 Creedmoor
10/18/2014
Just got a rifle that is a 6.5 Creedmore. This is going to help me with loads for this round.
Rate now:
loicnX174 MONTHS
Premium Member
Private
Rating: 0.0/5 this site
4 posts this site
Re: 6.5 Creedmoor
10/20/2014
Im new to the 6.5 creedmoor, cannot find any h4350 and I have been out of job for 2 months, so I tried with the varget I had on hand , it isnt bad at all until at least 600 yards. Now if can find a way to post pics., the gorum doesnt work anymore for mevwith tapatalk...
Rate now:
rhildy77XSergeant
Rating: 3.1/5 this site
286 posts this site
Re: 6.5 Creedmoor
10/20/2014
(2 votes)
Hornady brass
federal 210M
43.2 H4350
2.91 OAL
Rate now:
HumbleEinstein
XFirst Sergeant
Rating: 3.3/5 this site
1001 posts this site
Re: 6.5 Creedmoor
10/23/2014 Last edited 10/23/2014 by HumbleEinstein
(1 vote)
Here's my load:
Hornaday Brass (fully prepped, .289 bushing)
42.5 grains of IMR 4350
Berger 140 grain VLD Target (2.227" to ogive)
Federal 210M
Unfortunately, I pulled the last shot and I didn't have enough rounds to do it again.
[IMG2=JSON]{"alt":" photo ScreenShot2014-10-22at125519PM_zps75aefbdf.png","data-align":"none","data-size":"full","src":"http:\/\/i1349.photobucket.com\/albums\/p754\/HumbleEinstein\/Mobile%20Uploads\/ScreenShot2014-10-22at125519PM_zps75aefbdf.png"}[/IMG2]
[IMG2=JSON]{"alt":" photo ScreenShot2014-10-22at125441PM_zpsf539e1a2.png","data-align":"none","data-size":"full","src":"http:\/\/i1349.photobucket.com\/albums\/p754\/HumbleEinstein\/Mobile%20Uploads\/ScreenShot2014-10-22at125441PM_zpsf539e1a2.png"}[/IMG2]
Rate now:
wrhunterXSergeant
Rating: 3.0/5 this site
386 posts this site
Re: 6.5 Creedmoor
10/29/2014 Last edited 11/07/2014 by wrhunter
140 Amax 42g H4350
GM210M primers
2715 fps in a 22" tube
5 rounds cold bore @100yds
Had a sample pack of 140vld hunting so I tried 41.5g H4350 at a random mag friendly coal.
5 rounds @100 yards
Chamber was cut for the 140 Amax
Rate now:
triplecelectricXSergeant
Rating: 3.0/5 this site
408 posts this site
Re: 6.5 Creedmoor
10/30/2014
Looking for good succesful loads for a GAP 10 in 6.5 Creedmore.
Rate now:
JRedell
XGunny Sergeant
Rating: 3.3/5 this site
609 posts this site
Re: 6.5 Creedmoor
10/31/2014
Just found a pretty decent load for the wife's new PRS gun.
42.0gr H4350
140AMAX, 0.005" off the lands
CCI200 primer
Hornady brass
~2850fps out of a 26" Broughton
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
11/03/2014
139 Scenars
42.4gr H4350
Hornady Brass
FGM210M
2.25 Ogive
.035 off the lands
2785fps out of a 24" Bartlein
Rate now:
JGB02
XFirst Sergeant
Rating: 3.4/5 this site
1841 posts this site
Re: 6.5 Creedmoor
11/18/2014 Last edited 01/25/2015 by JGB02
26" 1/8 Bartlein barrel
Hornady brass
WLR primer
140gr AMAX
42.3gr H4350
~ 2705 FPS; I know I can load hotter, but this is really accurate and works well
Bullet insensitive to seating depth, so I load to mag length.
Rate now:
djskitXGunny Sergeant
Rating: 3.0/5 this site
572 posts this site
Re: 6.5 Creedmoor
11/26/2014
26 inch 1/8 Brux
139 scenar
43.3 H4350
.015 off the lands
CCI BR-2
2830 fps
Rate now:
KITTYCATMANX26 MONTHS
Premium Member
Corporal
Rating: 3.4/5 this site
49 posts this site
Re: 6.5 Creedmoor
11/27/2014
139gr Scenar
41.5gr H4350
Nosler Brass
CCI LRP
2,820 fps
26" AINA barrel (1:8" Bartlein 5r)
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
11/27/2014
(1 vote)
I've got several load combos.
42.4 H4350, Hornady brass, FGM210M, 140 vld at 2.140 to ogive
5 shots
[IMG2=JSON]{"alt":" photo 61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg"}[/IMG2]
5 at 890 yards
[IMG2=JSON]{"alt":" photo 6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg"}[/IMG2]
43.8 H4350 , 130 vld , all same as above , 2.135 to ogive.
2928 fps at 75 degrees and a 1/4 moa load.
My load for 30 degree weather and lower is 43.1 H4350 , a 140 hybrid at 2.125 to ogive. Is 2840 fps.
[IMG2=JSON]{"alt":" photo 0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2014-01\/0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg"}[/IMG2]
I've also had REALLY good results with 42.5 Reloader 17 with 140 amax, 140 vld , and 140 hybrid.
Gained about 75 to 90 fps with great , consistent hits at 1k.
XFirst Sergeant
Rating: 3.4/5 this site
2180 posts this site
6.5 Creedmoor
10/07/2014 Last edited 10/15/2014 by Thrust911
Load data....Bring it on over.
Original thread: **6.5 Creedmoor Loads**
Mine:
42.0gr H4350
139gr Lapua Scenar
GM210M Primer
2.84" COAL
~2765FPS 26" Bartlein barrel
Single digit SD out of a GAP
Rate now:
LawnMM
XFirst Sergeant
Rating: 3.4/5 this site
3146 posts this site
Re: 6.5 Creedmoor
10/13/2014
Lets see...
44.1gr H4350
123gr Lapua Scenar
CCI BR2
2.800" COAL
2925fps 22" Krieger
Single Digit SD, 8 I believe
Going to experiment with Varget, H4350 puts a lot of pressure back through the port, this is an auto loader. I've got a few components I'm going to swap to try and delay the timing on the cycle but if that doesn't work I may switch powders in an effort to get the gun running less harshly. Its putting a beating on the brass right now and I believe most of the problem has to do with the timing, rather than excessive pressure. Its a shame, because its a really accurate load.
Rate now:
MarcusW
X79 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
208 posts this site
Re: 6.5 Creedmoor
10/14/2014
H4350 load - has been stable across 3 out of 4 lots
43.0gr H4350
140gr Berger VLD (Hunting version seems more accurate but Target is still 1/2 MOA)
GM210M Primer
.020" Jump
2820FPS 26" Bartlein barrel
H100V load - Faster but fouls barrel very quickly, leaves heavy soot on case necks. Only tried 1 lot
42.5gr H100V
140gr Berger VLD
G210M Primer
.020" Jump
2870FPS 26" Bartlein barrel
Rate now:
cecchino76XFirst Sergeant
Rating: 3.0/5 this site
1682 posts this site
Re: 6.5 Creedmoor
10/14/2014
Tag
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
10/16/2014
(1 vote)
GAP CRUSADER 1:8.25 Bartlein Bbl, MTU contour, 27"
42.6 H4350 , 140 vld at 2.140 to Ogive, fgm210m, hornady brass , gives me 2810 to 2820 fps.
42.7 H4350 with a 140 Hybrid at 2.124 to ogive with all of the same above gives me 2830 fps.
[IMG2=JSON]{"alt":" photo F74E78B6-CC69-4B91-86FE-0E1F05B08DFE_zpsqdrez2wn.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/F74E78B6-CC69-4B91-86FE-0E1F05B08DFE_zpsqdrez2wn.jpg"}[/IMG2]
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
10/16/2014 Last edited 10/16/2014 by DarksideSix
tag
Rate now:
drglockXGunny Sergeant
Rating: 3.2/5 this site
580 posts this site
Re: 6.5 Creedmoor
10/16/2014
41.4gr H4350
140gr Amax
GM 210M Primer
2.805 COAL
~2720 FPS 23" 8.5 Twist Bartlein
.20 MOA PCR Build
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
10/16/2014
136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
Rate now:
m118lr762X27 MONTHS
Premium Member
Corporal
Rating: 3.0/5 this site
82 posts this site
Re: 6.5 Creedmoor
10/18/2014
Just got a rifle that is a 6.5 Creedmore. This is going to help me with loads for this round.
Rate now:
loicnX174 MONTHS
Premium Member
Private
Rating: 0.0/5 this site
4 posts this site
Re: 6.5 Creedmoor
10/20/2014
Im new to the 6.5 creedmoor, cannot find any h4350 and I have been out of job for 2 months, so I tried with the varget I had on hand , it isnt bad at all until at least 600 yards. Now if can find a way to post pics., the gorum doesnt work anymore for mevwith tapatalk...
Rate now:
rhildy77XSergeant
Rating: 3.1/5 this site
286 posts this site
Re: 6.5 Creedmoor
10/20/2014
(2 votes)
Hornady brass
federal 210M
43.2 H4350
2.91 OAL
Rate now:
HumbleEinstein
XFirst Sergeant
Rating: 3.3/5 this site
1001 posts this site
Re: 6.5 Creedmoor
10/23/2014 Last edited 10/23/2014 by HumbleEinstein
(1 vote)
Here's my load:
Hornaday Brass (fully prepped, .289 bushing)
42.5 grains of IMR 4350
Berger 140 grain VLD Target (2.227" to ogive)
Federal 210M
Unfortunately, I pulled the last shot and I didn't have enough rounds to do it again.
[IMG2=JSON]{"alt":" photo ScreenShot2014-10-22at125519PM_zps75aefbdf.png","data-align":"none","data-size":"full","src":"http:\/\/i1349.photobucket.com\/albums\/p754\/HumbleEinstein\/Mobile%20Uploads\/ScreenShot2014-10-22at125519PM_zps75aefbdf.png"}[/IMG2]
[IMG2=JSON]{"alt":" photo ScreenShot2014-10-22at125441PM_zpsf539e1a2.png","data-align":"none","data-size":"full","src":"http:\/\/i1349.photobucket.com\/albums\/p754\/HumbleEinstein\/Mobile%20Uploads\/ScreenShot2014-10-22at125441PM_zpsf539e1a2.png"}[/IMG2]
Rate now:
wrhunterXSergeant
Rating: 3.0/5 this site
386 posts this site
Re: 6.5 Creedmoor
10/29/2014 Last edited 11/07/2014 by wrhunter
140 Amax 42g H4350
GM210M primers
2715 fps in a 22" tube
5 rounds cold bore @100yds
Had a sample pack of 140vld hunting so I tried 41.5g H4350 at a random mag friendly coal.
5 rounds @100 yards
Chamber was cut for the 140 Amax
Rate now:
triplecelectricXSergeant
Rating: 3.0/5 this site
408 posts this site
Re: 6.5 Creedmoor
10/30/2014
Looking for good succesful loads for a GAP 10 in 6.5 Creedmore.
Rate now:
JRedell
XGunny Sergeant
Rating: 3.3/5 this site
609 posts this site
Re: 6.5 Creedmoor
10/31/2014
Just found a pretty decent load for the wife's new PRS gun.
42.0gr H4350
140AMAX, 0.005" off the lands
CCI200 primer
Hornady brass
~2850fps out of a 26" Broughton
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
11/03/2014
139 Scenars
42.4gr H4350
Hornady Brass
FGM210M
2.25 Ogive
.035 off the lands
2785fps out of a 24" Bartlein
Rate now:
JGB02
XFirst Sergeant
Rating: 3.4/5 this site
1841 posts this site
Re: 6.5 Creedmoor
11/18/2014 Last edited 01/25/2015 by JGB02
26" 1/8 Bartlein barrel
Hornady brass
WLR primer
140gr AMAX
42.3gr H4350
~ 2705 FPS; I know I can load hotter, but this is really accurate and works well
Bullet insensitive to seating depth, so I load to mag length.
Rate now:
djskitXGunny Sergeant
Rating: 3.0/5 this site
572 posts this site
Re: 6.5 Creedmoor
11/26/2014
26 inch 1/8 Brux
139 scenar
43.3 H4350
.015 off the lands
CCI BR-2
2830 fps
Rate now:
KITTYCATMANX26 MONTHS
Premium Member
Corporal
Rating: 3.4/5 this site
49 posts this site
Re: 6.5 Creedmoor
11/27/2014
139gr Scenar
41.5gr H4350
Nosler Brass
CCI LRP
2,820 fps
26" AINA barrel (1:8" Bartlein 5r)
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
11/27/2014
(1 vote)
I've got several load combos.
42.4 H4350, Hornady brass, FGM210M, 140 vld at 2.140 to ogive
5 shots
[IMG2=JSON]{"alt":" photo 61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg"}[/IMG2]
5 at 890 yards
[IMG2=JSON]{"alt":" photo 6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg"}[/IMG2]
43.8 H4350 , 130 vld , all same as above , 2.135 to ogive.
2928 fps at 75 degrees and a 1/4 moa load.
My load for 30 degree weather and lower is 43.1 H4350 , a 140 hybrid at 2.125 to ogive. Is 2840 fps.
[IMG2=JSON]{"alt":" photo 0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2014-01\/0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg"}[/IMG2]
I've also had REALLY good results with 42.5 Reloader 17 with 140 amax, 140 vld , and 140 hybrid.
Gained about 75 to 90 fps with great , consistent hits at 1k.
G
Guest
Guest
Gryph8nXFirst Sergeant
Rating: 3.1/5 this site
2653 posts this site
Re: 6.5 Creedmoor
12/01/2014
(1 vote)
I pretty much use the size charge at 42.8grs of RL17 for 140-142gr bullets in DTA with excellent results. Stopped using H4350 since I got so much more velocity and maintained good accuracy.
---------------------------------------------
--- Aimsmall55 wrote:
I've got several load combos.
42.4 H4350, Hornady brass, FGM210M, 140 vld at 2.140 to ogive
5 shots
[IMG2=JSON]{"alt":" photo 61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg"}[/IMG2]
5 at 890 yards
[IMG2=JSON]{"alt":" photo 6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg"}[/IMG2]
43.8 H4350 , 130 vld , all same as above , 2.135 to ogive.
2928 fps at 75 degrees and a 1/4 moa load.
My load for 30 degree weather and lower is 43.1 H4350 , a 140 hybrid at 2.125 to ogive. Is 2840 fps.
[IMG2=JSON]{"alt":" photo 0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2014-01\/0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg"}[/IMG2]
I've also had REALLY good results with 42.5 Reloader 17 with 140 amax, 140 vld , and 140 hybrid.
Gained about 75 to 90 fps with great , consistent hits at 1k.
---------------------------------------------
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
12/06/2014
Certainly not a typical load, but perfect when application calls for it. 108 Lapua, 210M, 39.7 Varget. Yeah, I pulled one in each group.
[IMG2=JSON]{"alt":" photo IMG_1094.jpg","data-align":"none","data-size":"full","src":"http:\/\/i293.photobucket.com\/albums\/mm79\/bbneuser\/Mobile%20Uploads\/IMG_1094.jpg"}[/IMG2]
Rate now:
eraveloX88 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
142 posts this site
Re: 6.5 Creedmoor
12/07/2014
Any info on DOPE to 800 and 1K?
How far off the lands, though these Scenar l's are not supposed to be as sensitive to jump?
Great shooting!
Rate now:
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
12/14/2014
130gr Berger Hunting VLD
42.4gr H4350
22" Bartlein
Chronoed 2747 @ 54.5*F on 12/13/14
SD 8 ES 20 with a magnetospeed
I've clocked this load at a faster speed in warmer weather. Anyone have a rought idea of what the muzzle velocity variation is with H4350?
1500+ rounds down the barrel and still hammers.
Rate now:
Rd001XPrivate
Rating: 0.0/5 this site
4 posts this site
Re: 6.5 Creedmoor
12/23/2014
39.4 grains of varget
120 grain Amax
Br2 primer
seated 2.750 overall length
this load combo works very well in my AO build. Usually shoots into the same hole at 100 yds.
sorry , no pics.
Rate now:
creedmoor1X27 MONTHS
Premium Member
Private
Rating: 3.0/5 this site
37 posts this site
Re: 6.5 Creedmoor
12/24/2014
6.5 creedmoor
139 scenars
42 g h4350
2 1/2 inch 5 shot group at 600 yards
though very accurate I do notice a 6 inch drop of bullet impact at 600 yds compared to factory hornady 139 loads.
I took three of the factory 139 loads apart and weighed the powder and it weighed in at 44.1 grains of h4350. That is a lot more than they say it is loaded at. So I have some more reloads done at 44 grains to see of I get similar bullet impacts at distance. I'll let you know what I find out.
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
01/02/2015
Rate now:
RangerWalker71
XFirst Sergeant
Rating: 3.0/5 this site
12770 posts this site
Re: 6.5 Creedmoor
01/03/2015
Tag for later.
Rate now:
TXBodeanXCorporal
Rating: 0.0/5 this site
72 posts this site
Re: 6.5 Creedmoor
01/03/2015
Berger 140g VLD Target
Fed 210 primers
2.800" OAL
42g RL17
2872fps 5 shot avg @40 degrees F/750' alt (9fps Std Dev) 26" Bartlien barrel
Ran out of Fed primers and using CCI Magnum LR #250 averaged 2883fps with 35fps Std Dev
Load developed using the OCW method with the Fed primers. 1/2 MOA @ 100yds
Rate now:
mmcmahXCorporal
Rating: 3.0/5 this site
83 posts this site
Re: 6.5 Creedmoor
01/16/2015
Tag... Going to start reloading for this cartridge.
Rating: 3.1/5 this site
2653 posts this site
Re: 6.5 Creedmoor
12/01/2014
(1 vote)
I pretty much use the size charge at 42.8grs of RL17 for 140-142gr bullets in DTA with excellent results. Stopped using H4350 since I got so much more velocity and maintained good accuracy.
---------------------------------------------
--- Aimsmall55 wrote:
I've got several load combos.
42.4 H4350, Hornady brass, FGM210M, 140 vld at 2.140 to ogive
5 shots
[IMG2=JSON]{"alt":" photo 61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/61C9B1E3-3FB3-4C9F-BCB5-89A02BC7B49E_zpswwa7wqlr.jpg"}[/IMG2]
5 at 890 yards
[IMG2=JSON]{"alt":" photo 6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6FC9750B-9585-4676-A601-0736BEB5042B_zpsqer9ugdu.jpg"}[/IMG2]
43.8 H4350 , 130 vld , all same as above , 2.135 to ogive.
2928 fps at 75 degrees and a 1/4 moa load.
My load for 30 degree weather and lower is 43.1 H4350 , a 140 hybrid at 2.125 to ogive. Is 2840 fps.
[IMG2=JSON]{"alt":" photo 0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2014-01\/0BA9B8E8-C04C-426C-9390-804FB604024D_zpsrmvtzg2m.jpg"}[/IMG2]
I've also had REALLY good results with 42.5 Reloader 17 with 140 amax, 140 vld , and 140 hybrid.
Gained about 75 to 90 fps with great , consistent hits at 1k.
---------------------------------------------
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
12/06/2014
Certainly not a typical load, but perfect when application calls for it. 108 Lapua, 210M, 39.7 Varget. Yeah, I pulled one in each group.
[IMG2=JSON]{"alt":" photo IMG_1094.jpg","data-align":"none","data-size":"full","src":"http:\/\/i293.photobucket.com\/albums\/mm79\/bbneuser\/Mobile%20Uploads\/IMG_1094.jpg"}[/IMG2]
Rate now:
eraveloX88 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
142 posts this site
Re: 6.5 Creedmoor
12/07/2014
NGCSUGrad09 wrote:
136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
That is going to be my next batch!136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
Any info on DOPE to 800 and 1K?
How far off the lands, though these Scenar l's are not supposed to be as sensitive to jump?
Great shooting!
Rate now:
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
12/14/2014
130gr Berger Hunting VLD
42.4gr H4350
22" Bartlein
Chronoed 2747 @ 54.5*F on 12/13/14
SD 8 ES 20 with a magnetospeed
I've clocked this load at a faster speed in warmer weather. Anyone have a rought idea of what the muzzle velocity variation is with H4350?
1500+ rounds down the barrel and still hammers.
Rate now:
Rd001XPrivate
Rating: 0.0/5 this site
4 posts this site
Re: 6.5 Creedmoor
12/23/2014
39.4 grains of varget
120 grain Amax
Br2 primer
seated 2.750 overall length
this load combo works very well in my AO build. Usually shoots into the same hole at 100 yds.
sorry , no pics.
Rate now:
creedmoor1X27 MONTHS
Premium Member
Private
Rating: 3.0/5 this site
37 posts this site
Re: 6.5 Creedmoor
12/24/2014
6.5 creedmoor
139 scenars
42 g h4350
2 1/2 inch 5 shot group at 600 yards
though very accurate I do notice a 6 inch drop of bullet impact at 600 yds compared to factory hornady 139 loads.
I took three of the factory 139 loads apart and weighed the powder and it weighed in at 44.1 grains of h4350. That is a lot more than they say it is loaded at. So I have some more reloads done at 44 grains to see of I get similar bullet impacts at distance. I'll let you know what I find out.
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
01/02/2015
eravelo wrote:
Any info on DOPE to 800 and 1K?
How far off the lands, though these Scenar l's are not supposed to be as sensitive to jump?
Great shooting!
With a DA of 2000, 6.3 Mils to 800yds and 9.2 Mils to 1000yards. My velocity requirement in load testing was only to keep at least 1000 yards on the first rotation of a 10 Mil per turn scope. I wanted something that was stupid accurate, and I got it really by accident.NGCSUGrad09 wrote:
136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
That is going to be my next batch!136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
Any info on DOPE to 800 and 1K?
How far off the lands, though these Scenar l's are not supposed to be as sensitive to jump?
Great shooting!
Rate now:
RangerWalker71
XFirst Sergeant
Rating: 3.0/5 this site
12770 posts this site
Re: 6.5 Creedmoor
01/03/2015
Tag for later.
Rate now:
TXBodeanXCorporal
Rating: 0.0/5 this site
72 posts this site
Re: 6.5 Creedmoor
01/03/2015
Berger 140g VLD Target
Fed 210 primers
2.800" OAL
42g RL17
2872fps 5 shot avg @40 degrees F/750' alt (9fps Std Dev) 26" Bartlien barrel
Ran out of Fed primers and using CCI Magnum LR #250 averaged 2883fps with 35fps Std Dev
Load developed using the OCW method with the Fed primers. 1/2 MOA @ 100yds
Rate now:
mmcmahXCorporal
Rating: 3.0/5 this site
83 posts this site
Re: 6.5 Creedmoor
01/16/2015
Tag... Going to start reloading for this cartridge.
G
Guest
Guest
TroyMN2XCorporal
Rating: 3.0/5 this site
69 posts this site
Re: 6.5 Creedmoor
01/17/2015
(1 vote)
Tag, I only hope my new LRP shoots like some of yours...thinking the 140 a-max might be my first load attempt
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/17/2015
Sean-
Just curious why loaded so short at 2.75 COAL? Short throated chamber or just looking to jump the bullet a significant amount? I just picked up about 900 of the Scenar L's and have had little opportunity to test much. Shooting in two AR's and one bolt gun, all of which have different lengths to touching lands.
Rate now:
ToonamiXPrivate
Rating: 0.0/5 this site
20 posts this site
Re: 6.5 Creedmoor
01/18/2015
Anyone have loads with Hybrid 100v pushing 140 berger hybrids that work good for then? Yes I know H4350 is the powder of choice but I cant get hold of any at reasonable prices.
Rate now:
lkesslerXPrivate
Rating: 3.0/5 this site
26 posts this site
Re: 6.5 Creedmoor
01/23/2015
What brand dies are you guys using
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/23/2015
Redding or Whidden FL sizing bushing dies with micrometer seating die. Either are very good, low runout if set up correctly. Use either with confidence. Have both AR's and bolt 6.5's, hence the FL sizing or you might get away with body die and neck size bushing setup if dedicated to one bolt rifle.
Rate now:
JGB02
XFirst Sergeant
Rating: 3.4/5 this site
1841 posts this site
Re: 6.5 Creedmoor
01/25/2015
43.1gr H4350
136gr Lapua Scenar
2.775 OAL
WLR Primer
~2820 FPS
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/26/2015
Same question as I'd posed to Sean-what's behind the short COAL? Throat length, mag length, bullet jump for this bullet in your gun, ?? I'm working with 136 Scenar in two AR's and one bolt, all with different length to touching lands and seeing your's at 2.77 and other at 2.75-both quite short-curious at to reasoning. Am loading to 2.100 to ogive, right at 2.82 overall.
Rate now:
JGB02
XFirst Sergeant
Rating: 3.4/5 this site
1841 posts this site
Re: 6.5 Creedmoor
01/26/2015
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
02/01/2015
Gents,
To answer your question, no other reason that they shoot really good! I was experimenting pushing them out, playing with mag length and then dropping them just to see what would happen. When I found that the shortest OAL I tried punched them into one hole, I decided to just stick to it and not worry.
Sorry I don't have a better answer than the load just shoots and it was a random experiment.
Rate now:
Moadster
XSergeant
Rating: 3.0/5 this site
167 posts this site
Re: 6.5 Creedmoor
02/02/2015
I've been running H100v for years with good results. I'm running 40.5gr with berger 140 hybrids in my POF 6.5cm, limited to 2.81oal, and averaging 2675fps out of a 22" Rock Creek Barrel. Got it up to 2750 with 41.5gr, but the primer pockets were getting loose by the 3rd load.
Rate now:
Shanerbanner10XFirst Sergeant
Rating: 3.3/5 this site
1853 posts this site
Re: 6.5 Creedmoor
02/03/2015
Hornady Brass 3x fired
H4350 - 42.7 grns
BR-2 Primer
Berger 140 Hybrids
2.820" COAL
2790 fps
Broughton barrel finished at 24"
Rate now:
Punisher29073
XFirst Sergeant
Rating: 3.5/5 this site
1429 posts this site
Re: 6.5 Creedmoor
02/23/2015
Man. My whammy must be hot but it isn't showing any pressure signs.
44.1 gr H4350
140 Amax
CCI 200
Hornady brass.
Trajectory trueing shows it is 2770 FPS out of a 20" rock creek.
Ryan
Rate now:
omnisX57 MONTHS
Premium Member
Private
Rating: 3.2/5 this site
16 posts this site
Re: 6.5 Creedmoor
02/23/2015
(1 vote)
Tag
Rate now:
jstuck624XSergeant
Rating: 3.0/5 this site
105 posts this site
Re: 6.5 Creedmoor
02/26/2015
(1 vote)
Tag
Rate now:
pby5catXSergeant
Rating: 3.0/5 this site
100 posts this site
Re: 6.5 Creedmoor
03/12/2015 Last edited 03/12/2015 by pby5cat
41.5gr H4350
140 AMAX
GM210M
2.810" COAL Mag length
2660 FPS 24" Criterion
DPMS large frame AR semi-auto, Fulton armory upper with 24" criterion and SLR gas block.
Note: minor pressure signs, other Semi will need to be careful
Note: hornady box recipy
Any data on RL26?
Rate now:
Jec375XSergeant
Rating: 3.1/5 this site
405 posts this site
Re: 6.5 Creedmoor
03/14/2015 Last edited 03/14/2015 by Jec375
140gr Amax
42.6 h4350
Oal. 2.810
Winchester LRP
26"Bartline 1-8.5
Mv 2810
140 Berger hybrid
42.8 h4350
Fed gm LRP
Oal. 2.805
26" Bartline 1-8.5
Mv 2828
Trued out to 750 yards and ran over a magneto v3
Also I opened a factory Amax the other day it has 43.7 of something, anyone know?
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
03/14/2015
42.3 H4350
Berger 140 Hybrids
2.222 to Ogive
Hornady brass
Fed 210M primers
MV 2761
SD 4.5
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
04/16/2015 Last edited 04/16/2015 by Jmartin2076
(1 vote)
I use 42.1 gns of RL 17 and CCI Br 2 primers to push 140 Hybrids to 2900 fps from a 26 in Bartlien with no pressure signs. Seated about 3 thou off the lands. Accuracy has been 1/2 MOA or smaller so far. Measured with a Magneto v3.
Rate now:
NevadaZielmeister
XFirst Sergeant
Rating: 2.6/5 this site
1095 posts this site
Re: 6.5 Creedmoor
04/16/2015
My setup will be very similar to your setup. Also, what kind of brass?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/17/2015
Well, my GAP 6.5 creedmor will be here TODAY!!! Coming Back from GA Precision after getting a new Krieger MTU 1:8 at 26". Apparently , it'll be about 1# heavier than the original Bartlein ( GAP # 7) I had on there. I've got several hundred rounds loaded, but I gotta ask, does anybody know where to find 140 Berger Hybrids???
Rate now:
DRYLAKES32
XPrivate
Rating: 0.0/5 this site
18 posts this site
Re: 6.5 Creedmoor
04/18/2015
Todd,
Bullets.com showing 100 count and 500 count In Stock. My go to as they're priced right, always arrive intact and ship quickly. Good luck with that new tube. Hope it shoots as good as the Bartlein did!
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
04/18/2015
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/18/2015
---------------------------------------------
--- DRYLAKES32 wrote:
Todd,
Bullets.com showing 100 count and 500 count In Stock. My go to as they're priced right, always arrive intact and ship quickly. Good luck with that new tube. Hope it shoots as good as the Bartlein did!
---------------------------------------------
After "shoot and clean" and got the copper fouling down to almost nothing. I pulled out some old hand loads from my last barrel. 140 hybrid at 2.125 to ogive with 42.4 h4350. I put 4 in the same hole, but as usual, I pulled the 5th shot high.
I'd say it's a shooter!!
[IMG2=JSON]{"alt":" photo 6F6A46B0-3498-4AEE-8B44-5F0700788CC1_zps7yrra5r1.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6F6A46B0-3498-4AEE-8B44-5F0700788CC1_zps7yrra5r1.jpg"}[/IMG2]
Rate now:
DRYLAKES32
XPrivate
Rating: 0.0/5 this site
18 posts this site
Re: 6.5 Creedmoor
04/18/2015
Hands Down!
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
04/22/2015 Last edited 04/26/2015 by Jmartin2076
(1 vote)
Sorry, been awhile since I've checked in. Temp has been from 45-65 degrees and seems pretty stable so far. I am going to try testing for stability this weekend, here's my plan. Put 5 rounds in an insulated case with an ice pack, 5 rounds in an insulated case with a chem hand warmer and leave 5 rounds at ambient temp. I will measure the temp of each batch before shooting, being careful not to let them sit in the chamber long. I'll record the MV on my Magneto v3 and use the info to measure MV change per temp change. I'll post my results when I get them.
Update: I tested the MV change of RL17 today. I put 5 rounds in a cooler with ice, 5 in a cooler with hand warmers and 5 left at ambient. They were all left in their container for about 2 hours. I checked the temp of each set before shooting and got 35, 55, 70. I loaded each set quickly to minimize heating or cooling and shot them quickly so they didn't sit in a warm chamber. Using a Magneto V3 I got the average for each set. I calculated MV change by subtracting the lowest MV from the the middle and dividing the difference by the diff. in temp for those two sets. I then did this for the mid and high sets. The MV change for the low to mid was 1.3 and the change for the mid to high was .8. I then used just the low temp set and high and did the same calc which gave me very close to 1. with the 3 to compare I feel very confident that RL17 is giving me a MV Change of 1 fps per degree F. I hope someone else runs a similar test and can compare results with mine but it looks like RL 17 is pretty stable.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/27/2015
(1 vote)
Update on my 6.5 Crusader. The Krieger isn't as fast as the Bartlein was but man is it accurate.
140 vld with 42.4 h4350.
78 F with a 100 yard zero.
372 yards- 1.5 mils
620 yards - 3.78 mils
790 yarss - 5.8 mils
890 yards- 6.8 mils
985 yards - 8.0 mils.
Running about 2790 to 2800 fps.
Had a 10" gong at 890 and put 5 that were 2 to 2 1/2" group tops. At 985, I actually shot a tighter group than at 885. I put three shots that were touching on plate.
So far I'm VERY happy with my results. Especially considering that these loads were all loaded about 10 months ago with my OLD barrel.
Rating: 3.0/5 this site
69 posts this site
Re: 6.5 Creedmoor
01/17/2015
(1 vote)
Tag, I only hope my new LRP shoots like some of yours...thinking the 140 a-max might be my first load attempt
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/17/2015
Sean-
Just curious why loaded so short at 2.75 COAL? Short throated chamber or just looking to jump the bullet a significant amount? I just picked up about 900 of the Scenar L's and have had little opportunity to test much. Shooting in two AR's and one bolt gun, all of which have different lengths to touching lands.
Rate now:
ToonamiXPrivate
Rating: 0.0/5 this site
20 posts this site
Re: 6.5 Creedmoor
01/18/2015
Anyone have loads with Hybrid 100v pushing 140 berger hybrids that work good for then? Yes I know H4350 is the powder of choice but I cant get hold of any at reasonable prices.
Rate now:
lkesslerXPrivate
Rating: 3.0/5 this site
26 posts this site
Re: 6.5 Creedmoor
01/23/2015
What brand dies are you guys using
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/23/2015
Redding or Whidden FL sizing bushing dies with micrometer seating die. Either are very good, low runout if set up correctly. Use either with confidence. Have both AR's and bolt 6.5's, hence the FL sizing or you might get away with body die and neck size bushing setup if dedicated to one bolt rifle.
Rate now:
JGB02
XFirst Sergeant
Rating: 3.4/5 this site
1841 posts this site
Re: 6.5 Creedmoor
01/25/2015
43.1gr H4350
136gr Lapua Scenar
2.775 OAL
WLR Primer
~2820 FPS
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/26/2015
Same question as I'd posed to Sean-what's behind the short COAL? Throat length, mag length, bullet jump for this bullet in your gun, ?? I'm working with 136 Scenar in two AR's and one bolt, all with different length to touching lands and seeing your's at 2.77 and other at 2.75-both quite short-curious at to reasoning. Am loading to 2.100 to ogive, right at 2.82 overall.
Rate now:
JGB02
XFirst Sergeant
Rating: 3.4/5 this site
1841 posts this site
Re: 6.5 Creedmoor
01/26/2015
bobketx wrote: Same question as I'd posed to Sean-what's behind the short COAL? Throat length, mag length, bullet jump for this bullet in your gun, ?? I'm working with 136 Scenar in two AR's and one bolt, all with different length to touching lands and seeing your's at 2.77 and other at 2.75-both quite short-curious at to reasoning. Am loading to 2.100 to ogive, right at 2.82 overall.
I'm not sure. I knew it was going to be safe in my rifle (I've gone up to 43.5gr w/ a 140 AMAX loaded at that length) so I figured I would try it out. I usually just load my rounds mag length, but to be honest I found almost no variation between mag length and standard SAAMI 2.810" w/ the 140 AMAX. I only had one box of these 136 scenars that I got as part of a trade, so I didn't want to go dicking around w/ load development. If I get more of these in the future I'll probably play around a bit more because I know I can load them hotter and longer and get more speed; but, for know I know I have a good starting point. Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
02/01/2015
Gents,
To answer your question, no other reason that they shoot really good! I was experimenting pushing them out, playing with mag length and then dropping them just to see what would happen. When I found that the shortest OAL I tried punched them into one hole, I decided to just stick to it and not worry.
Sorry I don't have a better answer than the load just shoots and it was a random experiment.
Rate now:
Moadster
XSergeant
Rating: 3.0/5 this site
167 posts this site
Re: 6.5 Creedmoor
02/02/2015
I've been running H100v for years with good results. I'm running 40.5gr with berger 140 hybrids in my POF 6.5cm, limited to 2.81oal, and averaging 2675fps out of a 22" Rock Creek Barrel. Got it up to 2750 with 41.5gr, but the primer pockets were getting loose by the 3rd load.
Rate now:
Shanerbanner10XFirst Sergeant
Rating: 3.3/5 this site
1853 posts this site
Re: 6.5 Creedmoor
02/03/2015
Hornady Brass 3x fired
H4350 - 42.7 grns
BR-2 Primer
Berger 140 Hybrids
2.820" COAL
2790 fps
Broughton barrel finished at 24"
Rate now:
Punisher29073
XFirst Sergeant
Rating: 3.5/5 this site
1429 posts this site
Re: 6.5 Creedmoor
02/23/2015
Man. My whammy must be hot but it isn't showing any pressure signs.
44.1 gr H4350
140 Amax
CCI 200
Hornady brass.
Trajectory trueing shows it is 2770 FPS out of a 20" rock creek.
Ryan
Rate now:
omnisX57 MONTHS
Premium Member
Private
Rating: 3.2/5 this site
16 posts this site
Re: 6.5 Creedmoor
02/23/2015
(1 vote)
Tag
Rate now:
jstuck624XSergeant
Rating: 3.0/5 this site
105 posts this site
Re: 6.5 Creedmoor
02/26/2015
(1 vote)
Tag
Rate now:
pby5catXSergeant
Rating: 3.0/5 this site
100 posts this site
Re: 6.5 Creedmoor
03/12/2015 Last edited 03/12/2015 by pby5cat
41.5gr H4350
140 AMAX
GM210M
2.810" COAL Mag length
2660 FPS 24" Criterion
DPMS large frame AR semi-auto, Fulton armory upper with 24" criterion and SLR gas block.
Note: minor pressure signs, other Semi will need to be careful
Note: hornady box recipy
Any data on RL26?
Rate now:
Jec375XSergeant
Rating: 3.1/5 this site
405 posts this site
Re: 6.5 Creedmoor
03/14/2015 Last edited 03/14/2015 by Jec375
140gr Amax
42.6 h4350
Oal. 2.810
Winchester LRP
26"Bartline 1-8.5
Mv 2810
140 Berger hybrid
42.8 h4350
Fed gm LRP
Oal. 2.805
26" Bartline 1-8.5
Mv 2828
Trued out to 750 yards and ran over a magneto v3
Also I opened a factory Amax the other day it has 43.7 of something, anyone know?
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
03/14/2015
42.3 H4350
Berger 140 Hybrids
2.222 to Ogive
Hornady brass
Fed 210M primers
MV 2761
SD 4.5
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
04/16/2015 Last edited 04/16/2015 by Jmartin2076
(1 vote)
I use 42.1 gns of RL 17 and CCI Br 2 primers to push 140 Hybrids to 2900 fps from a 26 in Bartlien with no pressure signs. Seated about 3 thou off the lands. Accuracy has been 1/2 MOA or smaller so far. Measured with a Magneto v3.
Rate now:
NevadaZielmeister
XFirst Sergeant
Rating: 2.6/5 this site
1095 posts this site
Re: 6.5 Creedmoor
04/16/2015
Jmartin2076 wrote:
I use 42.1 gns of RL 17 and CCI Br 2 primers to push 140 Hybrids to 2900 fps from a 26 in Bartlien with no pressure signs. Seated about 3 thou off the lands. Accuracy has been 1/2 MOA or smaller so far. Measured with a Magneto v3.
Do you think you could comment regarding what temperature you were shooting in? I like the numbers for Reloader 17 but have also heard horror stories regarding how it shoots REALLY fast on hot days. I use 42.1 gns of RL 17 and CCI Br 2 primers to push 140 Hybrids to 2900 fps from a 26 in Bartlien with no pressure signs. Seated about 3 thou off the lands. Accuracy has been 1/2 MOA or smaller so far. Measured with a Magneto v3.
My setup will be very similar to your setup. Also, what kind of brass?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/17/2015
Well, my GAP 6.5 creedmor will be here TODAY!!! Coming Back from GA Precision after getting a new Krieger MTU 1:8 at 26". Apparently , it'll be about 1# heavier than the original Bartlein ( GAP # 7) I had on there. I've got several hundred rounds loaded, but I gotta ask, does anybody know where to find 140 Berger Hybrids???
Rate now:
DRYLAKES32
XPrivate
Rating: 0.0/5 this site
18 posts this site
Re: 6.5 Creedmoor
04/18/2015
Todd,
Bullets.com showing 100 count and 500 count In Stock. My go to as they're priced right, always arrive intact and ship quickly. Good luck with that new tube. Hope it shoots as good as the Bartlein did!
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
04/18/2015
Aimsmall55 wrote: Well, my GAP 6.5 creedmor will be here TODAY!!! Coming Back from GA Precision after getting a new Krieger MTU 1:8 at 26". Apparently , it'll be about 1# heavier than the original Bartlein ( GAP # 7) I had on there. I've got several hundred rounds loaded, but I gotta ask, does anybody know where to find 140 Berger Hybrids???
Bullets.com is where I've been getting mine and they have a ton in stock.Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/18/2015
---------------------------------------------
--- DRYLAKES32 wrote:
Todd,
Bullets.com showing 100 count and 500 count In Stock. My go to as they're priced right, always arrive intact and ship quickly. Good luck with that new tube. Hope it shoots as good as the Bartlein did!
---------------------------------------------
After "shoot and clean" and got the copper fouling down to almost nothing. I pulled out some old hand loads from my last barrel. 140 hybrid at 2.125 to ogive with 42.4 h4350. I put 4 in the same hole, but as usual, I pulled the 5th shot high.
I'd say it's a shooter!!
[IMG2=JSON]{"alt":" photo 6F6A46B0-3498-4AEE-8B44-5F0700788CC1_zps7yrra5r1.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6F6A46B0-3498-4AEE-8B44-5F0700788CC1_zps7yrra5r1.jpg"}[/IMG2]
Rate now:
DRYLAKES32
XPrivate
Rating: 0.0/5 this site
18 posts this site
Re: 6.5 Creedmoor
04/18/2015
Hands Down!
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
04/22/2015 Last edited 04/26/2015 by Jmartin2076
(1 vote)
Sorry, been awhile since I've checked in. Temp has been from 45-65 degrees and seems pretty stable so far. I am going to try testing for stability this weekend, here's my plan. Put 5 rounds in an insulated case with an ice pack, 5 rounds in an insulated case with a chem hand warmer and leave 5 rounds at ambient temp. I will measure the temp of each batch before shooting, being careful not to let them sit in the chamber long. I'll record the MV on my Magneto v3 and use the info to measure MV change per temp change. I'll post my results when I get them.
Update: I tested the MV change of RL17 today. I put 5 rounds in a cooler with ice, 5 in a cooler with hand warmers and 5 left at ambient. They were all left in their container for about 2 hours. I checked the temp of each set before shooting and got 35, 55, 70. I loaded each set quickly to minimize heating or cooling and shot them quickly so they didn't sit in a warm chamber. Using a Magneto V3 I got the average for each set. I calculated MV change by subtracting the lowest MV from the the middle and dividing the difference by the diff. in temp for those two sets. I then did this for the mid and high sets. The MV change for the low to mid was 1.3 and the change for the mid to high was .8. I then used just the low temp set and high and did the same calc which gave me very close to 1. with the 3 to compare I feel very confident that RL17 is giving me a MV Change of 1 fps per degree F. I hope someone else runs a similar test and can compare results with mine but it looks like RL 17 is pretty stable.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/27/2015
(1 vote)
Update on my 6.5 Crusader. The Krieger isn't as fast as the Bartlein was but man is it accurate.
140 vld with 42.4 h4350.
78 F with a 100 yard zero.
372 yards- 1.5 mils
620 yards - 3.78 mils
790 yarss - 5.8 mils
890 yards- 6.8 mils
985 yards - 8.0 mils.
Running about 2790 to 2800 fps.
Had a 10" gong at 890 and put 5 that were 2 to 2 1/2" group tops. At 985, I actually shot a tighter group than at 885. I put three shots that were touching on plate.
So far I'm VERY happy with my results. Especially considering that these loads were all loaded about 10 months ago with my OLD barrel.
G
Guest
Guest
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
04/28/2015 Last edited 04/30/2015 by bornhunter04
Playing around with RL 17 right now. Will update this post with range report as soon as i shoot my test loads.
Speeds listed are for 1 shot only across magneto-speed just to get a rough idea of what kind of speed I'm looking at.
Plan is to shoot for accuracy this week and then chrono more loads to verify speed. Speed isn't worth much if i can't find an accurate load.
42.2 and 42.4 showed lots of promise, .25" groups with a couple of fliers (i can honestly take the blame for the fliers). Loaded up some 42.3gr to try next with 130gr berger vld's. Ran all the way to 43.0gr with 130's and no pressure signs.....
43.0gr gets me 2929 with a 130 berger from a 22" barrel......
123gr scenars
43.0gr 2906
43.5gr 2935
44.0gr 3006 (barely starting to see pressure signs with this one)
All from a 22" barrel.
Update:
checked the loads @ 100 but nothing was consistent enough for me to investigate further.....back to the drawing board. Do have some Berger 140's to try out with RL17 yet though.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/29/2015
(1 vote)
---------------------------------------------
--- bornhunter04 wrote:
Playing around with RL 17 right now. Will update this post with range report as soon as i shoot my test loads.
Speeds listed are for 1 shot only across magneto-speed just to get a rough idea of what kind of speed I'm looking at.
Plan is to shoot for accuracy this week and then chrono more loads to verify speed. Speed isn't worth much if i can't find an accurate load.
42.2 and 42.4 showed lots of promise, .25" groups with a couple of fliers (i can honestly take the blame for the fliers). Loaded up some 42.3gr to try next with 130gr berger vld's. Ran all the way to 43.0gr with 130's and no pressure signs.....
43.0gr gets me 2929 with a 130 berger from a 22" barrel......
123gr scenars
43.0gr 2906
43.5gr 2935
44.0gr 3006 (barely starting to see pressure signs with this one)
All from a 22" barrel.
I too played with R17 and 140 hybrids and 130 vlds. I shot 42.5 r17 with a 140 hybrid. Dope was 3.49 mils at 620, 5.15 at 790 , 6.2 at 890, 6.6 at 923, and 7.5 at 995 yards. Were running 2898 fps from a 26" Krieger 1:8 on a GAP Crusader.
My dope for the 130 vlds .... Same distances listed were
620- 3.17 mils
790- 4.7 mils
890-5.77 mils
923-6.15 mils
995-7 mils.
130's were running 3050 fps. 43.2 R17. At 2.140 to ogive. No overpressure what so ever , but they weren't NEARLY as accurate as the 140 hybrids.
Maybe they just aren't as accurate at that speed because my 43.8 h4350 load at 2940 KILLS!!
---------------------------------------------
Rate now:
edwalzerXPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
04/30/2015
I havent seen where anyone tried the 100gr vmax for accuracy in a CM.
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
05/09/2015
Anyone loading Lapua formed brass with the 140 hybrid or 140 Horn HPBT?
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
04/28/2015 Last edited 04/30/2015 by bornhunter04
Playing around with RL 17 right now. Will update this post with range report as soon as i shoot my test loads.
Speeds listed are for 1 shot only across magneto-speed just to get a rough idea of what kind of speed I'm looking at.
Plan is to shoot for accuracy this week and then chrono more loads to verify speed. Speed isn't worth much if i can't find an accurate load.
42.2 and 42.4 showed lots of promise, .25" groups with a couple of fliers (i can honestly take the blame for the fliers). Loaded up some 42.3gr to try next with 130gr berger vld's. Ran all the way to 43.0gr with 130's and no pressure signs.....
43.0gr gets me 2929 with a 130 berger from a 22" barrel......
123gr scenars
43.0gr 2906
43.5gr 2935
44.0gr 3006 (barely starting to see pressure signs with this one)
All from a 22" barrel.
Update:
checked the loads @ 100 but nothing was consistent enough for me to investigate further.....back to the drawing board. Do have some Berger 140's to try out with RL17 yet though.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/29/2015
(1 vote)
---------------------------------------------
--- bornhunter04 wrote:
Playing around with RL 17 right now. Will update this post with range report as soon as i shoot my test loads.
Speeds listed are for 1 shot only across magneto-speed just to get a rough idea of what kind of speed I'm looking at.
Plan is to shoot for accuracy this week and then chrono more loads to verify speed. Speed isn't worth much if i can't find an accurate load.
42.2 and 42.4 showed lots of promise, .25" groups with a couple of fliers (i can honestly take the blame for the fliers). Loaded up some 42.3gr to try next with 130gr berger vld's. Ran all the way to 43.0gr with 130's and no pressure signs.....
43.0gr gets me 2929 with a 130 berger from a 22" barrel......
123gr scenars
43.0gr 2906
43.5gr 2935
44.0gr 3006 (barely starting to see pressure signs with this one)
All from a 22" barrel.
I too played with R17 and 140 hybrids and 130 vlds. I shot 42.5 r17 with a 140 hybrid. Dope was 3.49 mils at 620, 5.15 at 790 , 6.2 at 890, 6.6 at 923, and 7.5 at 995 yards. Were running 2898 fps from a 26" Krieger 1:8 on a GAP Crusader.
My dope for the 130 vlds .... Same distances listed were
620- 3.17 mils
790- 4.7 mils
890-5.77 mils
923-6.15 mils
995-7 mils.
130's were running 3050 fps. 43.2 R17. At 2.140 to ogive. No overpressure what so ever , but they weren't NEARLY as accurate as the 140 hybrids.
Maybe they just aren't as accurate at that speed because my 43.8 h4350 load at 2940 KILLS!!
---------------------------------------------
Rate now:
edwalzerXPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
04/30/2015
I havent seen where anyone tried the 100gr vmax for accuracy in a CM.
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
05/09/2015
Anyone loading Lapua formed brass with the 140 hybrid or 140 Horn HPBT?
G
Guest
Guest
Longshot85XCorporal
Rating: 3.0/5 this site
61 posts this site
Re: 6.5 Creedmoor
05/14/2015
It would be greatly appreciated if anyone who has experience with IMR 4451 would chime in with any helpful tips, thanks.
Rate now:
HumbleEinstein
XFirst Sergeant
Rating: 3.3/5 this site
1001 posts this site
Re: 6.5 Creedmoor
05/19/2015 Last edited 05/19/2015 by HumbleEinstein
(1 vote)
New load.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
05/20/2015
[IMG2=JSON]{"alt":" photo A9DEA97D-83FC-4F0F-B775-D47F8AB12F4D_zpszyypmzkr.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2015-05\/A9DEA97D-83FC-4F0F-B775-D47F8AB12F4D_zpszyypmzkr.jpg"}[/IMG2]
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
05/21/2015
How much bullet jump do you use for the 140r Berger Hybrids?
Rate now:
AIS75XSergeant
Rating: 3.1/5 this site
130 posts this site
Re: 6.5 Creedmoor
05/24/2015
Since I have not seen any loads for the 142 Matchking here goes.
PCR Built Creedmoor Rem action
24" 1-8 Bartlien
42.6 gr H4350
142 sierra Matchking
2.815 OAL (jump .030)
1/4 min at 200 yds
Data showing its running right at 2800 fps. Ran it to 700 today and it looks very good.
Just starting with this load but I am very happy with what I'm seeing so far. Now for 1000yds plus......
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
05/30/2015 Last edited 05/30/2015 by ArmyJerry
Moving my other post over here so I can find it.
Testing the 140 Hybrid today
Rifle =
LRI Rem 700 build
24 inch Bart 8 twist M24 contour
Manners T4 mini Chassis / AI Mag
Bullet Berger 140 Hybrid
Horn Brass match prepped
H4350 42.5
Max COAL = 2.88
Max Ogive - 2.209
Bullet Seated ogive 2.179
Doing testing on seating depth today
Bullets seated from .005 to .050 off the lands with the 42.5 load.
Avg Speed 2819 fps
SD 4.0
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
06/11/2015
Rifle is a Short Action Customs with JAE chassis. Final load developed. 5 shot group with 4 bullets in the same hole. I pulled one high and left at 11 o'clock. 0.2 MOA. Velocity = 2,717 FPS.
Rate now:
Str8shooterTxXSergeant
Rating: 2.9/5 this site
149 posts this site
Re: 6.5 Creedmoor
06/12/2015
(1 vote)
The more I look at the 6.5CM the more I feel the power of the "force" calling me to change my 308 to 6.5....
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
06/13/2015
(1 vote)
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
06/15/2015
(2 votes)
Just do it Str8, but keep your 308 for zombie day,
Rate now:
dondlhmn
XGunny Sergeant
Rating: 3.0/5 this site
631 posts this site
Re: 6.5 Creedmoor
06/18/2015
136L Lapua Scenar
40 grains (weighed) H4350, FED GM210M primer
2758 FPS average for 10 shots over the Magneto Speed (My 26" light Varmint 1:8 twist Krieger barrels seem to run a tad faster than others are finding)
COAL is 2.845 (these are for a match where single loading is REQUIRED, but they will go through the magazine) but that length gives me .005 off the lands.
5 shot group @ 100 yards (kind of a breezy day) gave me .485" group.
Seems to be in the right speed area for me, but I am planning on doing up some loads between 40 grains and 42 grains and see what happens.
I use a load of H4350 with 43.5 grains and FED GM210M primer in my more "tactical" 6.5 Creedmoor, 123 grain Lapua at 2980 FPS over the Magneto Speed Chrono with all dies (I use a different set of dies for each) set differently (giving 2.797 COAL @ .006 off the lands). The "tactical" rifle is an M24 Kieger barrel in 8:1 twist finished at 26 inches and shoots well under one MOA...usually near down around .5 MOA even with an ole half blind and shaky guy like me shooting the groups.
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
06/23/2015
10 shots over the magnetospeed with H4350 @ 43.1 using a 130 grain Berger AR Hybrid seated -.010 from the lands.
Rate now:
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
06/23/2015 Last edited 06/24/2015 by bornhunter04
Niles, What length barrel? Bolt or gas gun?
Any one play with IMR 4451 yet? I've got a pound to try just haven't had a chance to make any loads with it yet.
IMR 4451
I loaded 41.5, 42.0, 42.5 with 130 vlds with ogive @ 2.151
42.5, 43.0, 43.5 with 123 scenars @ coal: 2.80
Going to try and shoot them tomorrow.
Update:
90* F 1000 Elevation 40% humidity 29.43 baro
22" barrel - badger micro FTE 3x fired brass not annealed
IMR 4451 - 3 shots each with magnetospeed V3 bayo and V1 display
130 Berger VLD - Ogive 2.151
41.5gr - 2708 SD 10
42.0gr - 2725 SD 11
42.5gr - 2798 SD 22
Didn't reach pressure signs with these yet.
123 Lapua Scenar - 2.800 COAL
42.5gr - 2847 SD 13
43.0gr - 2872 SD 10
43.5gr - 2909 SD 22
Ejector swipe on 43.5gr. Max pressure.
A couple loads showed some promise with the 130's. Would have to play with seating depth on 123's they're very picky in my rifle.
This powder has a different smell than any of the hodgdon powders, can't describe it, but it is familiar. Powder also meters very well.
Thought it was interesting how the SD's shot up with the higher charge weights. Not sure what's causing that.
Rate now:
Why1504X66 MONTHS
Premium Member
Sergeant
Rating: 3.3/5 this site
430 posts this site
Re: 6.5 Creedmoor
06/24/2015 Last edited 06/24/2015 by Why1504
I have an AIAT with a Mile Hih Shooting 26" 6.5 Creedmoor Tooley/Bartlin barrel.
Next week I plan to begin working on a load. The chamber measures to 1.955. I haven't measured to the lands yet.
My one shot brass all measures 1.928 to 1.932.
I plan to trim my brass to 1.928.
I have one pound of H4350 and RL15. Plan to test with 140 AMAX pills.
Can anyone advise on where I should start for my ladder test? Which powder? OAL suggestions? How much jump?
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
06/24/2015 Last edited 06/24/2015 by nilescoyote
To the question above yours, my 26" X-Caliber barrel is affixed to a Stiller bolt action and my chamber has the .199 freebore.
Seating depth testing at 300y, dots are 2"
I will be going with -.020 me thinks
I used the same elevation setting on all... interesting that the POI climbed the further I jumped.
This was also with freshly annealed brass, my magnetospeed clocked 2898 today with the bullets .020 off the lands. Air temp at time of shots was around 74
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
06/26/2015
Next week I plan to begin working on a load. The chamber measures to 1.955. I haven't measured to the lands yet.
My one shot brass all measures 1.928 to 1.932.
I plan to trim my brass to 1.928.
I have one pound of H4350 and RL15. Plan to test with 140 AMAX pills.
Can anyone advise on where I should start for my ladder test? Which powder? OAL suggestions? How much jump?
Rate now:
LukeNCMXXSergeant
Rating: 3.5/5 this site
398 posts this site
Re: 6.5 Creedmoor
06/26/2015
42.3g Hodgdon H4350 powder
140g Hornady A-Max bullet
CCI BR2 primer
2.835" COAL (.010" off the lands)
~2619 FPS 20" Brux 1:8 barrel
SD 4, ES 9
1xfired Hornady brass from factory match ammo.
Neck sized with a Lee Collet Die
Phoenix Custom Rifles barreled FN SPR
Rate now:
CSARFEXGunny Sergeant
Rating: 3.5/5 this site
806 posts this site
Re: 6.5 Creedmoor
07/01/2015 Last edited 07/02/2015 by CSARFE
>
Rate now:
capreppyXGunny Sergeant
Rating: 3.1/5 this site
501 posts this site
Re: 6.5 Creedmoor
07/02/2015
42.5gr H4350 (dispensed with RCBS ChargeMaster and then trickled up on RCBS 5-0-5)
Hornady 140 Amax
CCI BR-2
New Hornady Brass (flash hole deburred and primer pocket uniformed using K&M tools)
2.81 COAL
2830 fps out of a 26" CBI barrel (chrono'd on a MagnetoSpeed V3)
8 fps SD so I'm good with that
******
Confirmed DOPE out to 800. Variable winds up to 9 mph (absolutely gorgeous TX day)
85 deg
DA 2000'
1035'
30.01 in Hg
200 - .4
300 - 1.0
400 - 1.8
500 - 2.5
600 - 3.5
700 - 4.5
800 - 5.6
Rating: 3.0/5 this site
61 posts this site
Re: 6.5 Creedmoor
05/14/2015
It would be greatly appreciated if anyone who has experience with IMR 4451 would chime in with any helpful tips, thanks.
Rate now:
HumbleEinstein
XFirst Sergeant
Rating: 3.3/5 this site
1001 posts this site
Re: 6.5 Creedmoor
05/19/2015 Last edited 05/19/2015 by HumbleEinstein
(1 vote)
New load.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
05/20/2015
[IMG2=JSON]{"alt":" photo A9DEA97D-83FC-4F0F-B775-D47F8AB12F4D_zpszyypmzkr.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2015-05\/A9DEA97D-83FC-4F0F-B775-D47F8AB12F4D_zpszyypmzkr.jpg"}[/IMG2]
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
05/21/2015
How much bullet jump do you use for the 140r Berger Hybrids?
Rate now:
AIS75XSergeant
Rating: 3.1/5 this site
130 posts this site
Re: 6.5 Creedmoor
05/24/2015
Since I have not seen any loads for the 142 Matchking here goes.
PCR Built Creedmoor Rem action
24" 1-8 Bartlien
42.6 gr H4350
142 sierra Matchking
2.815 OAL (jump .030)
1/4 min at 200 yds
Data showing its running right at 2800 fps. Ran it to 700 today and it looks very good.
Just starting with this load but I am very happy with what I'm seeing so far. Now for 1000yds plus......
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
05/30/2015 Last edited 05/30/2015 by ArmyJerry
Moving my other post over here so I can find it.
Testing the 140 Hybrid today
Rifle =
LRI Rem 700 build
24 inch Bart 8 twist M24 contour
Manners T4 mini Chassis / AI Mag
Bullet Berger 140 Hybrid
Horn Brass match prepped
H4350 42.5
Max COAL = 2.88
Max Ogive - 2.209
Bullet Seated ogive 2.179
Doing testing on seating depth today
Bullets seated from .005 to .050 off the lands with the 42.5 load.
Avg Speed 2819 fps
SD 4.0
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
06/11/2015
Rifle is a Short Action Customs with JAE chassis. Final load developed. 5 shot group with 4 bullets in the same hole. I pulled one high and left at 11 o'clock. 0.2 MOA. Velocity = 2,717 FPS.
Rate now:
Str8shooterTxXSergeant
Rating: 2.9/5 this site
149 posts this site
Re: 6.5 Creedmoor
06/12/2015
(1 vote)
The more I look at the 6.5CM the more I feel the power of the "force" calling me to change my 308 to 6.5....
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
06/13/2015
(1 vote)
Str8shooterTx wrote:
The more I look at the 6.5CM the more I feel the power of the "force" calling me to change my 308 to 6.5....
I sold my .308 after I bought my 6.5CM. I never looked back.The more I look at the 6.5CM the more I feel the power of the "force" calling me to change my 308 to 6.5....
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
06/15/2015
(2 votes)
Just do it Str8, but keep your 308 for zombie day,
Rate now:
dondlhmn
XGunny Sergeant
Rating: 3.0/5 this site
631 posts this site
Re: 6.5 Creedmoor
06/18/2015
136L Lapua Scenar
40 grains (weighed) H4350, FED GM210M primer
2758 FPS average for 10 shots over the Magneto Speed (My 26" light Varmint 1:8 twist Krieger barrels seem to run a tad faster than others are finding)
COAL is 2.845 (these are for a match where single loading is REQUIRED, but they will go through the magazine) but that length gives me .005 off the lands.
5 shot group @ 100 yards (kind of a breezy day) gave me .485" group.
Seems to be in the right speed area for me, but I am planning on doing up some loads between 40 grains and 42 grains and see what happens.
I use a load of H4350 with 43.5 grains and FED GM210M primer in my more "tactical" 6.5 Creedmoor, 123 grain Lapua at 2980 FPS over the Magneto Speed Chrono with all dies (I use a different set of dies for each) set differently (giving 2.797 COAL @ .006 off the lands). The "tactical" rifle is an M24 Kieger barrel in 8:1 twist finished at 26 inches and shoots well under one MOA...usually near down around .5 MOA even with an ole half blind and shaky guy like me shooting the groups.
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
06/23/2015
10 shots over the magnetospeed with H4350 @ 43.1 using a 130 grain Berger AR Hybrid seated -.010 from the lands.
Rate now:
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
06/23/2015 Last edited 06/24/2015 by bornhunter04
Niles, What length barrel? Bolt or gas gun?
Any one play with IMR 4451 yet? I've got a pound to try just haven't had a chance to make any loads with it yet.
IMR 4451
I loaded 41.5, 42.0, 42.5 with 130 vlds with ogive @ 2.151
42.5, 43.0, 43.5 with 123 scenars @ coal: 2.80
Going to try and shoot them tomorrow.
Update:
90* F 1000 Elevation 40% humidity 29.43 baro
22" barrel - badger micro FTE 3x fired brass not annealed
IMR 4451 - 3 shots each with magnetospeed V3 bayo and V1 display
130 Berger VLD - Ogive 2.151
41.5gr - 2708 SD 10
42.0gr - 2725 SD 11
42.5gr - 2798 SD 22
Didn't reach pressure signs with these yet.
123 Lapua Scenar - 2.800 COAL
42.5gr - 2847 SD 13
43.0gr - 2872 SD 10
43.5gr - 2909 SD 22
Ejector swipe on 43.5gr. Max pressure.
A couple loads showed some promise with the 130's. Would have to play with seating depth on 123's they're very picky in my rifle.
This powder has a different smell than any of the hodgdon powders, can't describe it, but it is familiar. Powder also meters very well.
Thought it was interesting how the SD's shot up with the higher charge weights. Not sure what's causing that.
Rate now:
Why1504X66 MONTHS
Premium Member
Sergeant
Rating: 3.3/5 this site
430 posts this site
Re: 6.5 Creedmoor
06/24/2015 Last edited 06/24/2015 by Why1504
I have an AIAT with a Mile Hih Shooting 26" 6.5 Creedmoor Tooley/Bartlin barrel.
Next week I plan to begin working on a load. The chamber measures to 1.955. I haven't measured to the lands yet.
My one shot brass all measures 1.928 to 1.932.
I plan to trim my brass to 1.928.
I have one pound of H4350 and RL15. Plan to test with 140 AMAX pills.
Can anyone advise on where I should start for my ladder test? Which powder? OAL suggestions? How much jump?
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
06/24/2015 Last edited 06/24/2015 by nilescoyote
Why1504 wrote:
I have one pound of H4350 and RL15. Plan to test with 140 AMAX pills.
Can anyone advise on where I should start for my ladder test? Which powder? OAL suggestions? How much jump?
I started H4350 at 41 grains, you may find your first node around 41-41.5 and your second 42.4-42.9 with 139-142 class bullets.I have one pound of H4350 and RL15. Plan to test with 140 AMAX pills.
Can anyone advise on where I should start for my ladder test? Which powder? OAL suggestions? How much jump?
To the question above yours, my 26" X-Caliber barrel is affixed to a Stiller bolt action and my chamber has the .199 freebore.
Seating depth testing at 300y, dots are 2"
I will be going with -.020 me thinks
I used the same elevation setting on all... interesting that the POI climbed the further I jumped.
This was also with freshly annealed brass, my magnetospeed clocked 2898 today with the bullets .020 off the lands. Air temp at time of shots was around 74
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
06/26/2015
Why1504 wrote: I have an AIAT with a Mile Hih Shooting 26" 6.5 Creedmoor Tooley/Bartlin barrel.
Did you mean RL 17? I haven't heard of anyone using 15. I am using Rl 17 and getting 2900 fps at 42.1 gr.Next week I plan to begin working on a load. The chamber measures to 1.955. I haven't measured to the lands yet.
My one shot brass all measures 1.928 to 1.932.
I plan to trim my brass to 1.928.
I have one pound of H4350 and RL15. Plan to test with 140 AMAX pills.
Can anyone advise on where I should start for my ladder test? Which powder? OAL suggestions? How much jump?
Rate now:
LukeNCMXXSergeant
Rating: 3.5/5 this site
398 posts this site
Re: 6.5 Creedmoor
06/26/2015
42.3g Hodgdon H4350 powder
140g Hornady A-Max bullet
CCI BR2 primer
2.835" COAL (.010" off the lands)
~2619 FPS 20" Brux 1:8 barrel
SD 4, ES 9
1xfired Hornady brass from factory match ammo.
Neck sized with a Lee Collet Die
Phoenix Custom Rifles barreled FN SPR
Rate now:
CSARFEXGunny Sergeant
Rating: 3.5/5 this site
806 posts this site
Re: 6.5 Creedmoor
07/01/2015 Last edited 07/02/2015 by CSARFE
>
Rate now:
capreppyXGunny Sergeant
Rating: 3.1/5 this site
501 posts this site
Re: 6.5 Creedmoor
07/02/2015
42.5gr H4350 (dispensed with RCBS ChargeMaster and then trickled up on RCBS 5-0-5)
Hornady 140 Amax
CCI BR-2
New Hornady Brass (flash hole deburred and primer pocket uniformed using K&M tools)
2.81 COAL
2830 fps out of a 26" CBI barrel (chrono'd on a MagnetoSpeed V3)
8 fps SD so I'm good with that
******
Confirmed DOPE out to 800. Variable winds up to 9 mph (absolutely gorgeous TX day)
85 deg
DA 2000'
1035'
30.01 in Hg
200 - .4
300 - 1.0
400 - 1.8
500 - 2.5
600 - 3.5
700 - 4.5
800 - 5.6
G
Guest
Guest
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/07/2015
3 shots. 42.4 H4350. 140 hybrid at 2.200 to ogive. Gap Crusader
[IMG2=JSON]{"alt":" photo 0871BA9A-BE5D-4286-A0CF-92C188B78928_zpsuswwuii7.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/0871BA9A-BE5D-4286-A0CF-92C188B78928_zpsuswwuii7.jpg"}[/IMG2]
[IMG2=JSON]{"alt":" photo 73051400-31A6-4214-B91D-48638F7A6A0D_zpsbalq1fkd.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/73051400-31A6-4214-B91D-48638F7A6A0D_zpsbalq1fkd.jpg"}[/IMG2]
Rate now:
m118lr762X27 MONTHS
Premium Member
Corporal
Rating: 3.0/5 this site
82 posts this site
Re: 6.5 Creedmoor
07/11/2015
I recently got a rifle in 6.5 creedmoor. I bought 4 boxes of Hornday factory ammo so I could shoot the rifle. I now have brass, powder and bullets to start loading with. I am going to start with 41.5 grn H4350 and I am going to use both 140 grn Hornday AMAX and 140 grn Berger Hybrids bullets. Just something to start with. I have looked over all your post and have found some good data. Thanks.
Rate now:
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
07/13/2015 Last edited 07/20/2015 by bornhunter04
Tried out some of the 130 hybrids this weekend.
42.8 and 43.0 of H4350 @ 2.200 to Ogive is the node for me.
Was getting some pressure signs @ 43.0
42.8gr @ 2.200 CBTO gives me 2804 average with SD 8 from my 22" barrel.
Shot this load in a match this past weekend. Seemed to shoot pretty good at distance verified drop to 1k.
Rate now:
lsmull
XCorporal
Rating: 3.1/5 this site
55 posts this site
Re: 6.5 Creedmoor
07/19/2015
Some data. No pressure signs (as you can see I do not really push it). Pretty consistent 75 degree shooting days in the Bay Area. Blue figures are best groups (4 rounds). 140gr bests were one hole.
Rate now:
SanSooShooter7XPrivate
Rating: 3.1/5 this site
11 posts this site
Re: 6.5 Creedmoor
07/25/2015
(5 votes)
TAG... for later.. future gun build in the works
I took all the loads given with pertinent info and organized this list
Hope this helps someone else...
Rate now:
avboiler11
XFirst Sergeant
Rating: 3.6/5 this site
3492 posts this site
Re: 6.5 Creedmoor
07/27/2015
Savage 11 Trophy Predator Hunter (22" 1:8), velocities via Magnetospeed V2
140gr Hornady HPBT
Hornady Brass
CCI-200
2.81" COAL
41.5gr H4350: 2692fps
42.2gr H4350: 2753fps
Rate now:
mark5pt56
XFirst Sergeant
Rating: 3.0/5 this site
2406 posts this site
Re: 6.5 Creedmoor
07/31/2015 Last edited 07/31/2015 by mark5pt56
300 yards, 44.5 H4350/120 AMAX. 210M primer 2.820 OAL. 3 rd firing from factory, process on standard RCBS dies. 2918 avg via Magnetospeed, 22" Bartlein 6.5CM
Second pic is factory 120.
[/IMG]
[/IMG]
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/31/2015
Gap Crusader. Hornady brass. Fgm210m.
123 grain AMAX at 2.204 to ogive (2.780) 41.8 varget
26" Krieger 1:8 mtu
5 shots with sd of 4 and average of 3,040 fps.
.28 moa at 100 yards
Rate now:
avboiler11
XFirst Sergeant
Rating: 3.6/5 this site
3492 posts this site
Re: 6.5 Creedmoor
08/04/2015
Remington 700 "Rem-Age" Criterion 26" 1:8 varmint contour
140gr Hornady HPBT
42.5gr H4350
Hornady Brass
CCI-200
2.81" COAL
2823fps, SD 9 via Magnetospeed V2
2857fps from Hornady 140gr Amax Match factory ammo
Rate now:
Diablo4130
XCorporal
Rating: 3.0/5 this site
97 posts this site
Re: 6.5 Creedmoor
08/06/2015
Anyone shooting 130gr Barnes TSX's?
Looking for a hunting load using either 4350 or RL-17.
Thanks
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
08/07/2015
Nice work San! ANy way that can get moved to the front page and stickied there?
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/07/2015
3 shots. 42.4 H4350. 140 hybrid at 2.200 to ogive. Gap Crusader
[IMG2=JSON]{"alt":" photo 0871BA9A-BE5D-4286-A0CF-92C188B78928_zpsuswwuii7.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/0871BA9A-BE5D-4286-A0CF-92C188B78928_zpsuswwuii7.jpg"}[/IMG2]
[IMG2=JSON]{"alt":" photo 73051400-31A6-4214-B91D-48638F7A6A0D_zpsbalq1fkd.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/73051400-31A6-4214-B91D-48638F7A6A0D_zpsbalq1fkd.jpg"}[/IMG2]
Rate now:
m118lr762X27 MONTHS
Premium Member
Corporal
Rating: 3.0/5 this site
82 posts this site
Re: 6.5 Creedmoor
07/11/2015
I recently got a rifle in 6.5 creedmoor. I bought 4 boxes of Hornday factory ammo so I could shoot the rifle. I now have brass, powder and bullets to start loading with. I am going to start with 41.5 grn H4350 and I am going to use both 140 grn Hornday AMAX and 140 grn Berger Hybrids bullets. Just something to start with. I have looked over all your post and have found some good data. Thanks.
Rate now:
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
07/13/2015 Last edited 07/20/2015 by bornhunter04
Tried out some of the 130 hybrids this weekend.
42.8 and 43.0 of H4350 @ 2.200 to Ogive is the node for me.
Was getting some pressure signs @ 43.0
42.8gr @ 2.200 CBTO gives me 2804 average with SD 8 from my 22" barrel.
Shot this load in a match this past weekend. Seemed to shoot pretty good at distance verified drop to 1k.
Rate now:
lsmull
XCorporal
Rating: 3.1/5 this site
55 posts this site
Re: 6.5 Creedmoor
07/19/2015
Some data. No pressure signs (as you can see I do not really push it). Pretty consistent 75 degree shooting days in the Bay Area. Blue figures are best groups (4 rounds). 140gr bests were one hole.
| 6.5 Creedmoor JPMR10 1:8 22" New Hornady Brass | Notation: | G1 | G2 | G3 | G4 | G5 | G6 | G7 | |||||
| H4350 | Max Charge | Start Factor | 4 Rds | 4 Rds | 4 Rds | 4 Rds | 4 Rds | 4 Rds | 4 Rds | Total Rds | |||
| 2 | 140gr Berger Match Target Hybrids | 43.0 | 40.0 | 40.6 | 41.0 | 41.4 | 41.8 | 42.2 | 42.6 | 43.0 | 34 | 0.020 | 2.241 |
| MV | 2695/4.4 | 2712/3.0 | 2746/13.0 | 2772/5.0 | 2789/10.1 | 2815/10.2 | 2829/7.9 | ||||||
| 3 | 140gr SMK HPBT match | 43.0 | 40.0 | 40.6 | 41.0 | 41.4 | 41.8 | 42.2 | 42.6 | 43.0 | 34 | 0.015 | 2.231 |
| MV | 2707/7.8 | 2733/8.1 | 2753/6.1 | 2785/8.4 | 2794/1.4 | 2827/8.1 | 2851/13.4 | ||||||
| 6 | 136gr Scenar-L Jacketed HPBT | 42.0 | 37.6 | 38.4 | 39.0 | 39.5 | 40.1 | 40.7 | 41.3 | 42.0 | 31 | 0.015 | 2.230 |
| MV | 2521/5.6 | 2570/13.0 | 2617/16.5 | 2647/20.2 | 2716/4.5 | 2744/10.3 | 2778/9.7 | ||||||
| 9 | 123gr SMK HPBT match | 44.8 | 40.1 | 40.9 | 41.6 | 42.2 | 42.8 | 43.5 | 44.1 | 44.8 | 37 | 0.020 | 2.230 |
| MV | 2683/11.3 | 2747/37.2 | 2773/13 | 2826/16.3 | 2866/8.0 | 2905/15.9 | 2963/8.8 |
Rate now:
SanSooShooter7XPrivate
Rating: 3.1/5 this site
11 posts this site
Re: 6.5 Creedmoor
07/25/2015
(5 votes)
TAG... for later.. future gun build in the works
I took all the loads given with pertinent info and organized this list
Hope this helps someone else...
| POWDER | CHG | BULLET | FPS | PRIMER | BARREL INFO | ADTNL INFO | |||
| H100V | 42.5 | 140 VLD | 2870 | GM210M | 26" BARTLEIN | ||||
| H100V | 40.5 | 140 HYBRID | 2675 | WLR | 22" ROCK CREEK | ||||
| H100V | 41.5 | 140 HYBRID | 2750 | WLR | 22" ROCK CREEK | LOOSE PRIMERS | |||
| H4350 | 42.6 | 142 SMK | 2800 | ? | 24" BARTLEIN | 1:8 TW | |||
| H4350 | 43 | 140 VLD | 2820 | GM210M | 26" BARTLEIN | ||||
| H4350 | 42.6 | 140 VLD | 2815 | GM210M | 27" BARTLEIN | ||||
| H4350 | 42.6 | 140 VLD | 2817 | GM210M | SD: 4.0 | ||||
| H4350 | 42.4 | 140 VLD | 2795 | ? | |||||
| H4350 | 43.1 | 140 HYBRID | 2840 | ||||||
| H4350 | 42.9 | 140 HYBRID | 2834 | GM210M | SD: 10.3 | ||||
| H4350 | 42.8 | 140 HYBRID | 2828 | GM LR | 26" BARTLEIN | 1:8.5 TW | |||
| H4350 | 42.7 | 140 HYBRID | 2830 | GM210M | ? | ||||
| H4350 | 42.5 | 140 HYBRID | 2819 | 24" BARTLEIN | SD: 4 | ||||
| H4350 | 42.3 | 140 HYBRID | 2761 | GM210M | SD: 4.5 | ||||
| H4350 | 44.1 | 140 AMAX | 2770 | CCI 200 | 20" ROCK CREEK | ||||
| H4350 | 42.6 | 140 AMAX | 2810 | WLR | 26" BARTLEIN | 1:8.5 TW | |||
| H4350 | 42.5 | 140 AMAX | 2830 | CCI BR2 | 26" | SD: 8 | |||
| H4350 | 42.3 | 140 AMAX | 2705 | WLR | 26" BARTLEIN | 1:8 TW | |||
| H4350 | 42.3 | 140 AMAX | 2619 | CCI BR2 | 20" BRUX | SD: 4 | |||
| H4350 | 42 | 140 AMAX | 2715 | GM210M | 22" | ||||
| H4350 | 42 | 140 AMAX | 2850 | CCI 200 | 26" BROUGHTON | ||||
| H4350 | 41.5 | 140 AMAX | 2660 | GM210M | 24" CRITERION | AR PLATFORM | |||
| H4350 | 41.4 | 140 AMAX | 2720 | GM210M | 23" BARTLEIN | ||||
| H4350 | 43.3 | 139 SCENAR | 2830 | CCI BR2 | 26" BRUX | 1:8 TW | |||
| H4350 | 42.4 | 139 SCENAR | 2785 | GM210M | 24" BARTLEIN | ||||
| H4350 | 42 | 139 SCENAR | 2765 | GM210M | 26" BARTLEIN | ||||
| H4350 | 41.5 | 139 SCENAR | 2820 | CCI 200 | 26" BARTLEIN | 1:8 TW | |||
| H4350 | 43.1 | 136 SCENAR | 2820 | ? | ? | ||||
| H4350 | 41.1 | 136 SCENAR | 2610 | CCI BR2 | 21" BARTLEIN | ||||
| H4350 | 43.8 | 130 VLD | 2928 | ||||||
| H4350 | 43.1 | 130 VLD | 2884 | ? | ? | ||||
| H4350 | 42.4 | 130 VLD | 2747 | ? | 22" BARTLEIN | ||||
| H4350 | 42.8 | 130 HYBRID | 2804 | 22" | |||||
| H4350 | 44.1 | 123 SCENAR | 2925 | CCI BR2 | 22" KREIGER | ||||
| IMR 4350 | 42.5 | 140 VLD | ? | GM210M | ? | ||||
| IMR 4451 | 42.5 | 130 VLD | 2798 | SD: 22 | |||||
| IMR 4451 | 42 | 130 VLD | 2725 | SD: 11 | |||||
| IMR 4451 | 41.5 | 130 VLD | 2708 | SD: 10 | |||||
| REL 17 | 42 | 140 VLD | 2872 | GM210M | 26" BARTLEIN | ||||
| REL 17 | 42.1 | 140 HYBRID | 2900 | CCI BR2 | 26" BARTLEIN | ||||
| REL 17 | 43 | 130 VLD | 2929 | ? | 22" |
Rate now:
avboiler11
XFirst Sergeant
Rating: 3.6/5 this site
3492 posts this site
Re: 6.5 Creedmoor
07/27/2015
Savage 11 Trophy Predator Hunter (22" 1:8), velocities via Magnetospeed V2
140gr Hornady HPBT
Hornady Brass
CCI-200
2.81" COAL
41.5gr H4350: 2692fps
42.2gr H4350: 2753fps
Rate now:
mark5pt56
XFirst Sergeant
Rating: 3.0/5 this site
2406 posts this site
Re: 6.5 Creedmoor
07/31/2015 Last edited 07/31/2015 by mark5pt56
300 yards, 44.5 H4350/120 AMAX. 210M primer 2.820 OAL. 3 rd firing from factory, process on standard RCBS dies. 2918 avg via Magnetospeed, 22" Bartlein 6.5CM
Second pic is factory 120.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/31/2015
Gap Crusader. Hornady brass. Fgm210m.
123 grain AMAX at 2.204 to ogive (2.780) 41.8 varget
26" Krieger 1:8 mtu
5 shots with sd of 4 and average of 3,040 fps.
.28 moa at 100 yards
Rate now:
avboiler11
XFirst Sergeant
Rating: 3.6/5 this site
3492 posts this site
Re: 6.5 Creedmoor
08/04/2015
Remington 700 "Rem-Age" Criterion 26" 1:8 varmint contour
140gr Hornady HPBT
42.5gr H4350
Hornady Brass
CCI-200
2.81" COAL
2823fps, SD 9 via Magnetospeed V2
2857fps from Hornady 140gr Amax Match factory ammo
Rate now:
Diablo4130
XCorporal
Rating: 3.0/5 this site
97 posts this site
Re: 6.5 Creedmoor
08/06/2015
Anyone shooting 130gr Barnes TSX's?
Looking for a hunting load using either 4350 or RL-17.
Thanks
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
08/07/2015
Nice work San! ANy way that can get moved to the front page and stickied there?
G
Guest
Guest
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
08/13/2015 Last edited 09/11/2015 by Brosome
Berger 140gr Hybrid loaded .2 off Jam.
H414 - 42gr
Hornady Brass
Federal GM210M primer
Barrel 26" Hawk Hill marksman contour
Average velocity: 2760fps
Newer to reloading and decided to try some H414 when I found a deal on it and couldn't find any H4350. Probably should have done some more research other than finding out its just a ball powder version of the 4350. Some notes on the load I've noticed: its somewhat dirty, not awful or unbearable, but a bit more soot on the case necks and in the barrel. Accuracy was good, .5 from a 10 shot group at 100y off a bipod and concrete bench. SD was 20, obviously not the greatest but Im going to chalk some of that up to being newer to reloading and having some looser neck tensions from bullets I had to tap out a bit and seat to the right length, a little better loading on my part im sure would drop that down a lot.
Edit: SD 10
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/18/2015 Last edited 08/18/2015 by Aimsmall55
GAP CRUSADER. 26"'Krieger MTU 1:8.
140 vld at 2.190 to ogive. 42.4 H4350. Fgm210m
2795 fps average.
6 shots at 102 yards .20 moa
[IMG2=JSON]{"alt":" photo 6C812D98-E974-48BE-B0D8-144DEC263A28_zpsdxvlzgzg.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6C812D98-E974-48BE-B0D8-144DEC263A28_zpsdxvlzgzg.jpg"}[/IMG2]
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
08/20/2015
My powder is shipping from powder valley tomorrow. I should have some loads worked up in about 2 weeks.
Thank you all for this great info source
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/21/2015
Ok so I went back and measured my throat. It's eroded just a little. Not hardly at all.
So I decided to take some 1x brass, use a redding type S FL die with a .289 bushing and bumped the shoulder back 2 1/2/1000"s.
The load : 42.5 H4350 , 140 hunting vld at 2.210 to ogive. 1x brass fl sized.
The results....
I do believe this is the best group I've shot to date with this new bbl. .13 moa!
[IMG2=JSON]{"alt":" photo 3FCD2C18-1780-4165-B903-B2912D9A24F2_zps5vlgdqwj.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2015-08\/3FCD2C18-1780-4165-B903-B2912D9A24F2_zps5vlgdqwj.png"}[/IMG2]
[IMG2=JSON]{"alt":" photo DBC0B944-29CC-4056-854B-79670FE346AE_zpsohbl8ic6.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2015-08\/DBC0B944-29CC-4056-854B-79670FE346AE_zpsohbl8ic6.jpg"}[/IMG2]
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
08/22/2015
That's a serious tight group.
Congrats. Looks like you found a great load.
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
08/22/2015
Aimsmall
+1 to above comment-truly good shooting, and load workup. Gotta say, you've set the bar pretty high and have given me proper motivation to continuously improve my skills set, both behind the rifle-semi or bolt, and at the load bench. Nice work, sir.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/22/2015
---------------------------------------------
--- bobketx wrote:
Aimsmall
+1 to above comment-truly good shooting, and load workup. Gotta say, you've set the bar pretty high and have given me proper motivation to continuously improve my skills set, both behind the rifle-semi or bolt, and at the load bench. Nice work, sir.
---------------------------------------------
I appreciate it. It's been a process. I figured that since GAP used the same reamer, I would have no problem getting (with the exact same loads) the results of my last bbl, a Bartlein , at 27" 1:8.5 that had a slightly smaller contour.
This new bbl is 26" Krieger MTU 1:8 and is definitely heavier than my previous bbl. Plus GAP had to put in a barrel pad because of the dimensions of the MTU.
I started playing with OAL and realized this particular setup likes the bullets MUCH closer to the lands. I was jumping them 90-1000"s with my old bbl. Now I'm only .20 off.
Hell, I had just began to come to grips that this was just NOT going to shoot as good as the last bbl.
I guess it just goes to show you never know until you keep playing with it.
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
08/22/2015
Curiously, what optic have you settled on for your particular needs?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/22/2015
---------------------------------------------
--- bobketx wrote:
Curiously, what optic have you settled on for your particular needs?
---------------------------------------------
I've had a NF NXS 5.5x22x56 mildot. A Bushnell XRS and ERS. I decided to go with the ERS not just because of the FFP, but also that it's 3.5x21 is all I really need out to 1400 yards or so.
Rate now:
spoon063XFirst Sergeant
Rating: 3.0/5 this site
1290 posts this site
Re: 6.5 Creedmoor
08/23/2015
Has anyone run 130 bergers with Varget at all?
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
08/25/2015 Last edited 08/27/2015 by nilescoyote
(1 vote)
In an attempt to figure out what rifle I am using this year for Montana mule, I decided to shoot some 140 A-Max for the first time in this barrel using the same load that works well with 139 scenars, 42.7 grains of H4350. And I figured that with a longer bearing surface it might be good to drop it back a couple tenths (42.5) just in case the increased length raised the pressure and put me out of the 139 node. I seated the bullets -.029" back from a hard seat in the lands.
At the range, I hooked up the magnetospeed (my new way of running a OCW test) and fired the four rounds of 42.5... 2796fps SD=1 ES=3, I kind of kick my self when I show that as those were the only 4 I had bought.
Moving on to 42.7 I had 2810fps SD=3 ES=8...
So with my remaining rounds of 42.7 I detached the magnetospeed and put a couple rounds down range at 3, 4 and 6 hundred to see if Ballistic AE was tracking with the new data and was rewarded with near center hits. Looked at my predicted drop for 1k and dialed that in to the scope and started shooting while holding about half a mil.
While watching the impacts I could tell today was going to be a good day and then promptly threw the next shot a touch high. LOL so I sent an extra one just for good measure.
After shooting another rifle I came back to shoot the smaller steel target on the right with the creedmoor and finished off the remaining 4 rounds.
Minus the high impact the left target has 2.5" of vertical and the 4 on the right target has 2.25" of vertical.
Not a bad day.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/25/2015
---------------------------------------------
--- nilescoyote wrote:
In an attempt to figure out what rifle I am using this year for Montana mule, I decided to shoot some 140 A-Max for the first time in this barrel using the same load that works well with 139 scenars, 42.7 grains of H4350. And I figured that with a longer bearing surface it might be good to drop it back a couple tenths (42.5) just in case the increased length raised the pressure and put me out of the 139 node. I seated the bullets -.029" back from a hard seat in the lands.
At the range, I hooked up the magnetospeed (my new way of running a OCW test) and fired the four rounds of 42.5... 2796fps SD=1 ES=3, I kind of kick my self when I show that as those were the only 4 I had bought.
Moving on to 42.7 I had 2810fps SD=3 ES=8...
So with my remaining rounds of 42.7 I detached the magnetospeed and put a couple rounds down range at 3, 4 and 6 hundred to see if Ballistic AE was tracking with the new data and was rewarded with near center hits. Looked at my predicted drop for 1k and dialed that in to the scope and started shooting while holding about half a mil.
While watching the impacts I could tell today was going to be a good day and then promptly threw the next shot a touch high. LOL so I sent an extra one just for good measure.
After shooting another rifle I came back to shoot the smaller steel target on the right with the creedmoor and finished off the remaining 4 rounds.
Minus the high impact the left target has 2.5" of vertical and the 4 on the right target has 2.25" of vertical.
Not a bad day.
---------------------------------------------
Two words : HELL YES
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
08/13/2015 Last edited 09/11/2015 by Brosome
Berger 140gr Hybrid loaded .2 off Jam.
H414 - 42gr
Hornady Brass
Federal GM210M primer
Barrel 26" Hawk Hill marksman contour
Average velocity: 2760fps
Newer to reloading and decided to try some H414 when I found a deal on it and couldn't find any H4350. Probably should have done some more research other than finding out its just a ball powder version of the 4350. Some notes on the load I've noticed: its somewhat dirty, not awful or unbearable, but a bit more soot on the case necks and in the barrel. Accuracy was good, .5 from a 10 shot group at 100y off a bipod and concrete bench. SD was 20, obviously not the greatest but Im going to chalk some of that up to being newer to reloading and having some looser neck tensions from bullets I had to tap out a bit and seat to the right length, a little better loading on my part im sure would drop that down a lot.
Edit: SD 10
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/18/2015 Last edited 08/18/2015 by Aimsmall55
GAP CRUSADER. 26"'Krieger MTU 1:8.
140 vld at 2.190 to ogive. 42.4 H4350. Fgm210m
2795 fps average.
6 shots at 102 yards .20 moa
[IMG2=JSON]{"alt":" photo 6C812D98-E974-48BE-B0D8-144DEC263A28_zpsdxvlzgzg.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/shooting%20pics\/6C812D98-E974-48BE-B0D8-144DEC263A28_zpsdxvlzgzg.jpg"}[/IMG2]
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
08/20/2015
My powder is shipping from powder valley tomorrow. I should have some loads worked up in about 2 weeks.
Thank you all for this great info source
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/21/2015
Ok so I went back and measured my throat. It's eroded just a little. Not hardly at all.
So I decided to take some 1x brass, use a redding type S FL die with a .289 bushing and bumped the shoulder back 2 1/2/1000"s.
The load : 42.5 H4350 , 140 hunting vld at 2.210 to ogive. 1x brass fl sized.
The results....
I do believe this is the best group I've shot to date with this new bbl. .13 moa!
[IMG2=JSON]{"alt":" photo 3FCD2C18-1780-4165-B903-B2912D9A24F2_zps5vlgdqwj.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2015-08\/3FCD2C18-1780-4165-B903-B2912D9A24F2_zps5vlgdqwj.png"}[/IMG2]
[IMG2=JSON]{"alt":" photo DBC0B944-29CC-4056-854B-79670FE346AE_zpsohbl8ic6.jpg","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2015-08\/DBC0B944-29CC-4056-854B-79670FE346AE_zpsohbl8ic6.jpg"}[/IMG2]
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
08/22/2015
That's a serious tight group.
Congrats. Looks like you found a great load.
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
08/22/2015
Aimsmall
+1 to above comment-truly good shooting, and load workup. Gotta say, you've set the bar pretty high and have given me proper motivation to continuously improve my skills set, both behind the rifle-semi or bolt, and at the load bench. Nice work, sir.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/22/2015
---------------------------------------------
--- bobketx wrote:
Aimsmall
+1 to above comment-truly good shooting, and load workup. Gotta say, you've set the bar pretty high and have given me proper motivation to continuously improve my skills set, both behind the rifle-semi or bolt, and at the load bench. Nice work, sir.
---------------------------------------------
I appreciate it. It's been a process. I figured that since GAP used the same reamer, I would have no problem getting (with the exact same loads) the results of my last bbl, a Bartlein , at 27" 1:8.5 that had a slightly smaller contour.
This new bbl is 26" Krieger MTU 1:8 and is definitely heavier than my previous bbl. Plus GAP had to put in a barrel pad because of the dimensions of the MTU.
I started playing with OAL and realized this particular setup likes the bullets MUCH closer to the lands. I was jumping them 90-1000"s with my old bbl. Now I'm only .20 off.
Hell, I had just began to come to grips that this was just NOT going to shoot as good as the last bbl.
I guess it just goes to show you never know until you keep playing with it.
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
08/22/2015
Curiously, what optic have you settled on for your particular needs?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/22/2015
---------------------------------------------
--- bobketx wrote:
Curiously, what optic have you settled on for your particular needs?
---------------------------------------------
I've had a NF NXS 5.5x22x56 mildot. A Bushnell XRS and ERS. I decided to go with the ERS not just because of the FFP, but also that it's 3.5x21 is all I really need out to 1400 yards or so.
Rate now:
spoon063XFirst Sergeant
Rating: 3.0/5 this site
1290 posts this site
Re: 6.5 Creedmoor
08/23/2015
Has anyone run 130 bergers with Varget at all?
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
08/25/2015 Last edited 08/27/2015 by nilescoyote
(1 vote)
In an attempt to figure out what rifle I am using this year for Montana mule, I decided to shoot some 140 A-Max for the first time in this barrel using the same load that works well with 139 scenars, 42.7 grains of H4350. And I figured that with a longer bearing surface it might be good to drop it back a couple tenths (42.5) just in case the increased length raised the pressure and put me out of the 139 node. I seated the bullets -.029" back from a hard seat in the lands.
At the range, I hooked up the magnetospeed (my new way of running a OCW test) and fired the four rounds of 42.5... 2796fps SD=1 ES=3, I kind of kick my self when I show that as those were the only 4 I had bought.
Moving on to 42.7 I had 2810fps SD=3 ES=8...
So with my remaining rounds of 42.7 I detached the magnetospeed and put a couple rounds down range at 3, 4 and 6 hundred to see if Ballistic AE was tracking with the new data and was rewarded with near center hits. Looked at my predicted drop for 1k and dialed that in to the scope and started shooting while holding about half a mil.
While watching the impacts I could tell today was going to be a good day and then promptly threw the next shot a touch high. LOL so I sent an extra one just for good measure.
After shooting another rifle I came back to shoot the smaller steel target on the right with the creedmoor and finished off the remaining 4 rounds.
Minus the high impact the left target has 2.5" of vertical and the 4 on the right target has 2.25" of vertical.
Not a bad day.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
08/25/2015
---------------------------------------------
--- nilescoyote wrote:
In an attempt to figure out what rifle I am using this year for Montana mule, I decided to shoot some 140 A-Max for the first time in this barrel using the same load that works well with 139 scenars, 42.7 grains of H4350. And I figured that with a longer bearing surface it might be good to drop it back a couple tenths (42.5) just in case the increased length raised the pressure and put me out of the 139 node. I seated the bullets -.029" back from a hard seat in the lands.
At the range, I hooked up the magnetospeed (my new way of running a OCW test) and fired the four rounds of 42.5... 2796fps SD=1 ES=3, I kind of kick my self when I show that as those were the only 4 I had bought.
Moving on to 42.7 I had 2810fps SD=3 ES=8...
So with my remaining rounds of 42.7 I detached the magnetospeed and put a couple rounds down range at 3, 4 and 6 hundred to see if Ballistic AE was tracking with the new data and was rewarded with near center hits. Looked at my predicted drop for 1k and dialed that in to the scope and started shooting while holding about half a mil.
While watching the impacts I could tell today was going to be a good day and then promptly threw the next shot a touch high. LOL so I sent an extra one just for good measure.
After shooting another rifle I came back to shoot the smaller steel target on the right with the creedmoor and finished off the remaining 4 rounds.
Minus the high impact the left target has 2.5" of vertical and the 4 on the right target has 2.25" of vertical.
Not a bad day.
---------------------------------------------
Two words : HELL YES
G
Guest
Guest
rduckworXGunny Sergeant
Rating: 3.3/5 this site
776 posts this site
Re: 6.5 Creedmoor
08/26/2015 Last edited 08/26/2015 by rduckwor
"42.5... 2796fps SD=1 ES=3,
Moving on to 42.7 I had 2810fps SD=3 ES=8... "
Damnnation! I don't know what you are doing to your brass and loading procedure, but I want some of it!!!
Those are superb numbers!
RMD
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
08/27/2015 Last edited 08/27/2015 by nilescoyote
My process is simple. On this batch of brass I had just annealed them. Resized leaving about .0035 neck tension, threw them in my vibrating tumbler for a couple hours, clean the primer pockets out afterward and primed, charged and seated the night before.
One change over how I have loaded 139 scenars in the past (which has good numbers also just not quite single digit ES) is I seated the bullets -.029 deep rather than .020-.025
Rate now:
rduckworXGunny Sergeant
Rating: 3.3/5 this site
776 posts this site
Re: 6.5 Creedmoor
08/30/2015
RMD
Rate now:
rduckworXGunny Sergeant
Rating: 3.3/5 this site
776 posts this site
Re: 6.5 Creedmoor
08/30/2015
Thanks and great loading/shooting.
RMD
Rate now:
thisguy65
XSergeant
Rating: 3.0/5 this site
331 posts this site
Re: 6.5 Creedmoor
08/31/2015
Hey guys, finally getting my gear to reload. First time dealing with the Hybrids but what do they typically like .020 jump?
Since I'm reloading for matches the velocity is what it is after doing a OCW test. No way to increase velocity with out getting off the node, correct?
Rate now:
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
09/02/2015
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
09/02/2015
Finally got 5 lbs of H4350 and was able to work up a load without the RL 17. Had a real nice group going until I pulled that one bottom left out a bit but still very happy with it. Now to test for Velocity change over temp.
42.5gr H4350
140gr Berg Hyb
.006 jump to lands- CBTO 2.174
CCI BR2 primers
2805 fps (magnetospeed) 26in Bartlien- SD 9, ED 23
Rate now:
davidwalter59XGunny Sergeant
Rating: 3.1/5 this site
751 posts this site
Re: 6.5 Creedmoor
09/06/2015 Last edited 09/08/2015 by davidwalter59
Has anyone tried Ramshot big Game? Manual says 123 AMAX over 43 grains. I think the burn rate is the same as IMR 4350.
Rate now:
ratrod54X45 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
331 posts this site
Re: 6.5 Creedmoor
09/06/2015 Last edited 09/07/2015 by ratrod54
Bartlein barrel 1:8 Twist 23"
41.1 grains H4350
130gr VLD Hunting
Hornady brass
Federal 210M primer
.020 off the lands
It's stupid accurate. .3MOA @100 and same results at 500.
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
09/17/2015
What length are you all trimming the brass to?
Books say 1.910". Is that what you're using?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
09/21/2015
Was looking at all my good .25 moa loads from my old 27" Bartlein and my new loads for my 26" 1:8 MTU Bartlein on a GAP CRUSADER
Hope this will help
Gap 6.5 creedmor loads
140 vld. 42.4 H4350, 2.140 to ogive. Fgm210m
140 hybrid at 2.125 to ogive 42.6 H4350, 42.5 r17
130 vld at 2.140 to ogive. 44.0 h4350 2930 fps.
139 scenar at 2.229 to ogive. 40.8 r17. 2780 fps at 10 ft. .22 MOA 7 shots.
140 amax. 42.7 r17. 2.800"
2910 fps.
42.7 r17. 140 hybrid at 2.125. 2920 fps.
****COLD WEATHER****
43.1 H4350. 140 hybrid at 2.155 to ogive. 2800 fps.
New BBL 4/24/15
140 vld. 2.136 to ogive. 42.4 H4350 , fgm210 m. 2790 fps.
(Now shoots at 2815 fps after 125 rounds )
Rate now:
avboiler11
XFirst Sergeant
Rating: 3.6/5 this site
3492 posts this site
Re: 6.5 Creedmoor
09/24/2015
140gr Hornady HPBT
42.5gr H4350
Hornady Brass
CCI-200
2.81" COAL
2640fps
123gr Amax
40.7gr Varget
Hornady Brass
CCI-200
2.81" COAL
2810fps
Hornady 140gr Amax Match factory ammo
2662fps
Rate now:
HazzapatrolX55 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
202 posts this site
Re: 6.5 Creedmoor
09/29/2015 Last edited 10/01/2015 by Hazzapatrol
42.3 gr H4350
Berger 140 Hybrid Target
GM210M Primer
2.223 base to ogive
~2737 FPS out of a 23" Bartlein 5r, 1:8 twist
10 shots over a magnetospeed gave an SD of 3 and consistently under 9 over multiple sessions
</p
Rate now:
Relay123XPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
10/05/2015
I see that some (most) you shoot bartlein barrels for the 6.5 creedmoor. I have a lulja barrel on a Remington short action. Do you find that you have to let the barrel warm up a bit before the rifle starts to perform well? I find that I need to shoot 5 to 10 rounds before the rifle settles in and gives good groups ie. quarter minute. I don't have this problem with the other rifles I own and it kind of tweaks me; mostly when shooting out past 800 yards. Also, whats your case life like? Because I see that some shooter's loads are 2-3 grains more than what most reloading books recommend. I'm still loading cases that have been shot 10 times or more. I'm loading 40+ grains of H-4350 with a 140 A-Max, out a 26" barrel. It's cronograghing at 2,625. I'll take less case life if I can add more velocity without the loss of accuracy. Maybe it's time to ditch my barrel for a different one? Please excuse my ignorance if you have already covered this subject before. This is my first post so I'm a cherry at this. "blush"
Rate now:
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
10/07/2015
Are you cleaning your barrel after everytime you shoot it? If you are that would make sense, your first several shots are fouling the barrel then once it reaches a level of fouling it likes the groups tighten up. As far as velocity, run another load development with those amax's maybe starting where you're at now and working up slow watching for pressure signs you should find another node around the ~42gr+ area.
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
10/12/2015 Last edited 03/07/2016 by jhayesvw
I guess I never put my data up.
I'm using 142 SMKs
I've found 41.5 and 42 grains H4350 to produce .5 MOA groups out of my Ruger PR. Which is likely the best it'll get.
They chrono 2675 at 10' with a CED M2 chrono.
Now 41.5 chronos 2730 fps out of the 24" RPR barrel.
I'm taking them to 1000 yards in a couple weeks.
Rate now:
JRHill85XSergeant
Rating: 3.1/5 this site
313 posts this site
Re: 6.5 Creedmoor
10/23/2015
For those loading with 142 SMK's how far are you guys jumping them? I can get good groups .02" off with Varget, but they're around 2625 if I remember correctly. Went .015" off with H4350 but can't really find anything worth duplicating. I've always found it pretty easy to find a good load until I ordered 800 142 SMK's ?. It seems like the faster I shoot them the more they open up
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
11/01/2015
Rating: 3.3/5 this site
776 posts this site
Re: 6.5 Creedmoor
08/26/2015 Last edited 08/26/2015 by rduckwor
"42.5... 2796fps SD=1 ES=3,
Moving on to 42.7 I had 2810fps SD=3 ES=8... "
Damnnation! I don't know what you are doing to your brass and loading procedure, but I want some of it!!!
Those are superb numbers!
RMD
Rate now:
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
08/27/2015 Last edited 08/27/2015 by nilescoyote
rduckwor wrote: "42.5... 2796fps SD=1 ES=3,
Moving on to 42.7 I had 2810fps SD=3 ES=8... "
Damnnation! I don't know what you are doing to your brass and loading procedure, but I want some of it!!!
Those are superb numbers!
RMD
I had to look at it twice while I was recording itl. Just remember this was only for four rounds each... As good as 42.7 shot at 1k I am tempted to leave it alone and just keep loading that, but numbers on 43.5 have me second guessing. Might load up 10 of each and see what I see.Moving on to 42.7 I had 2810fps SD=3 ES=8... "
Damnnation! I don't know what you are doing to your brass and loading procedure, but I want some of it!!!
Those are superb numbers!
RMD
My process is simple. On this batch of brass I had just annealed them. Resized leaving about .0035 neck tension, threw them in my vibrating tumbler for a couple hours, clean the primer pockets out afterward and primed, charged and seated the night before.
One change over how I have loaded 139 scenars in the past (which has good numbers also just not quite single digit ES) is I seated the bullets -.029 deep rather than .020-.025
Rate now:
rduckworXGunny Sergeant
Rating: 3.3/5 this site
776 posts this site
Re: 6.5 Creedmoor
08/30/2015
spoon063 wrote:
Has anyone run 130 bergers with Varget at all?
I have some and just set up the first ocw run with H4350. I think I will try some Varget when time allows. Keep you posted.Has anyone run 130 bergers with Varget at all?
RMD
Rate now:
rduckworXGunny Sergeant
Rating: 3.3/5 this site
776 posts this site
Re: 6.5 Creedmoor
08/30/2015
nilescoyote wrote:
My process is simple. On this batch of brass I had just annealed them. Resized leaving about .0035 neck tension, threw them in my vibrating tumbler for a couple hours, clean the primer pockets out afterward and primed, charged and seated the night before.
One change over how I have loaded 139 scenars in the past (which has good numbers also just not quite single digit ES) is I seated the bullets -.029 deep rather than .020-.025
I just loaded up two OCW runs with the 140 AMAX and the 130 Berger Hybrid. I will see what the numbers look like and then try your method of seating the AMAX a bit longer.rduckwor wrote: "42.5... 2796fps SD=1 ES=3,
Moving on to 42.7 I had 2810fps SD=3 ES=8... "
Damnnation! I don't know what you are doing to your brass and loading procedure, but I want some of it!!!
Those are superb numbers!
RMD
I had to look at it twice while I was recording itl. Just remember this was only for four rounds each... As good as 42.7 shot at 1k I am tempted to leave it alone and just keep loading that, but numbers on 43.5 have me second guessing. Might load up 10 of each and see what I see.Moving on to 42.7 I had 2810fps SD=3 ES=8... "
Damnnation! I don't know what you are doing to your brass and loading procedure, but I want some of it!!!
Those are superb numbers!
RMD
My process is simple. On this batch of brass I had just annealed them. Resized leaving about .0035 neck tension, threw them in my vibrating tumbler for a couple hours, clean the primer pockets out afterward and primed, charged and seated the night before.
One change over how I have loaded 139 scenars in the past (which has good numbers also just not quite single digit ES) is I seated the bullets -.029 deep rather than .020-.025
Thanks and great loading/shooting.
RMD
Rate now:
thisguy65
XSergeant
Rating: 3.0/5 this site
331 posts this site
Re: 6.5 Creedmoor
08/31/2015
Hey guys, finally getting my gear to reload. First time dealing with the Hybrids but what do they typically like .020 jump?
Since I'm reloading for matches the velocity is what it is after doing a OCW test. No way to increase velocity with out getting off the node, correct?
Rate now:
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
09/02/2015
thisguy65 wrote:
Hey guys, finally getting my gear to reload. First time dealing with the Hybrids but what do they typically like .020 jump?
Since I'm reloading for matches the velocity is what it is after doing a OCW test. No way to increase velocity with out getting off the node, correct?
Mine liked the .02 jumps the best for the 140 hybrids. As far as velocity you're right you're going to want to find a nod in the velocity you're looking for. Hey guys, finally getting my gear to reload. First time dealing with the Hybrids but what do they typically like .020 jump?
Since I'm reloading for matches the velocity is what it is after doing a OCW test. No way to increase velocity with out getting off the node, correct?
Rate now:
Jmartin2076
XSergeant
Rating: 3.2/5 this site
156 posts this site
Re: 6.5 Creedmoor
09/02/2015
Finally got 5 lbs of H4350 and was able to work up a load without the RL 17. Had a real nice group going until I pulled that one bottom left out a bit but still very happy with it. Now to test for Velocity change over temp.
42.5gr H4350
140gr Berg Hyb
.006 jump to lands- CBTO 2.174
CCI BR2 primers
2805 fps (magnetospeed) 26in Bartlien- SD 9, ED 23
Rate now:
davidwalter59XGunny Sergeant
Rating: 3.1/5 this site
751 posts this site
Re: 6.5 Creedmoor
09/06/2015 Last edited 09/08/2015 by davidwalter59
Has anyone tried Ramshot big Game? Manual says 123 AMAX over 43 grains. I think the burn rate is the same as IMR 4350.
Rate now:
ratrod54X45 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
331 posts this site
Re: 6.5 Creedmoor
09/06/2015 Last edited 09/07/2015 by ratrod54
NGCSUGrad09 wrote:
136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
I was lucky and stumbled across a similar load.136gr Scenar-L
41.1 gr H4350
CCI BR2
Hornady brass
2.75" COAL
2610fps out of a 21" Bartlein
Shoots less than a quarter minute at 100, sub half MOA at 800 and sub MOA at 1300yds.
Bartlein barrel 1:8 Twist 23"
41.1 grains H4350
130gr VLD Hunting
Hornady brass
Federal 210M primer
.020 off the lands
It's stupid accurate. .3MOA @100 and same results at 500.
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
09/17/2015
What length are you all trimming the brass to?
Books say 1.910". Is that what you're using?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
09/21/2015
Was looking at all my good .25 moa loads from my old 27" Bartlein and my new loads for my 26" 1:8 MTU Bartlein on a GAP CRUSADER
Hope this will help
Gap 6.5 creedmor loads
140 vld. 42.4 H4350, 2.140 to ogive. Fgm210m
140 hybrid at 2.125 to ogive 42.6 H4350, 42.5 r17
130 vld at 2.140 to ogive. 44.0 h4350 2930 fps.
139 scenar at 2.229 to ogive. 40.8 r17. 2780 fps at 10 ft. .22 MOA 7 shots.
140 amax. 42.7 r17. 2.800"
2910 fps.
42.7 r17. 140 hybrid at 2.125. 2920 fps.
****COLD WEATHER****
43.1 H4350. 140 hybrid at 2.155 to ogive. 2800 fps.
New BBL 4/24/15
140 vld. 2.136 to ogive. 42.4 H4350 , fgm210 m. 2790 fps.
(Now shoots at 2815 fps after 125 rounds )
Rate now:
avboiler11
XFirst Sergeant
Rating: 3.6/5 this site
3492 posts this site
Re: 6.5 Creedmoor
09/24/2015
avboiler11 wrote: Remington 700 "Rem-Age" Criterion 26" 1:8 varmint contour
140gr Hornady HPBT
42.5gr H4350
Hornady Brass
CCI-200
2.81" COAL
2823fps, SD 9 via Magnetospeed V2
2857fps from Hornady 140gr Amax Match factory ammo
With this barrel cut back to 18"...140gr Hornady HPBT
42.5gr H4350
Hornady Brass
CCI-200
2.81" COAL
2823fps, SD 9 via Magnetospeed V2
2857fps from Hornady 140gr Amax Match factory ammo
140gr Hornady HPBT
42.5gr H4350
Hornady Brass
CCI-200
2.81" COAL
2640fps
123gr Amax
40.7gr Varget
Hornady Brass
CCI-200
2.81" COAL
2810fps
Hornady 140gr Amax Match factory ammo
2662fps
Rate now:
HazzapatrolX55 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
202 posts this site
Re: 6.5 Creedmoor
09/29/2015 Last edited 10/01/2015 by Hazzapatrol
42.3 gr H4350
Berger 140 Hybrid Target
GM210M Primer
2.223 base to ogive
~2737 FPS out of a 23" Bartlein 5r, 1:8 twist
10 shots over a magnetospeed gave an SD of 3 and consistently under 9 over multiple sessions
</p
Rate now:
Relay123XPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
10/05/2015
I see that some (most) you shoot bartlein barrels for the 6.5 creedmoor. I have a lulja barrel on a Remington short action. Do you find that you have to let the barrel warm up a bit before the rifle starts to perform well? I find that I need to shoot 5 to 10 rounds before the rifle settles in and gives good groups ie. quarter minute. I don't have this problem with the other rifles I own and it kind of tweaks me; mostly when shooting out past 800 yards. Also, whats your case life like? Because I see that some shooter's loads are 2-3 grains more than what most reloading books recommend. I'm still loading cases that have been shot 10 times or more. I'm loading 40+ grains of H-4350 with a 140 A-Max, out a 26" barrel. It's cronograghing at 2,625. I'll take less case life if I can add more velocity without the loss of accuracy. Maybe it's time to ditch my barrel for a different one? Please excuse my ignorance if you have already covered this subject before. This is my first post so I'm a cherry at this. "blush"
Rate now:
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
10/07/2015
Are you cleaning your barrel after everytime you shoot it? If you are that would make sense, your first several shots are fouling the barrel then once it reaches a level of fouling it likes the groups tighten up. As far as velocity, run another load development with those amax's maybe starting where you're at now and working up slow watching for pressure signs you should find another node around the ~42gr+ area.
Rate now:
jhayesvwXGunny Sergeant
Rating: 3.4/5 this site
984 posts this site
Re: 6.5 Creedmoor
10/12/2015 Last edited 03/07/2016 by jhayesvw
I guess I never put my data up.
I'm using 142 SMKs
I've found 41.5 and 42 grains H4350 to produce .5 MOA groups out of my Ruger PR. Which is likely the best it'll get.
They chrono 2675 at 10' with a CED M2 chrono.
Now 41.5 chronos 2730 fps out of the 24" RPR barrel.
I'm taking them to 1000 yards in a couple weeks.
Rate now:
JRHill85XSergeant
Rating: 3.1/5 this site
313 posts this site
Re: 6.5 Creedmoor
10/23/2015
For those loading with 142 SMK's how far are you guys jumping them? I can get good groups .02" off with Varget, but they're around 2625 if I remember correctly. Went .015" off with H4350 but can't really find anything worth duplicating. I've always found it pretty easy to find a good load until I ordered 800 142 SMK's ?. It seems like the faster I shoot them the more they open up
Rate now:
steinmasterXSergeant
Rating: 3.4/5 this site
488 posts this site
Re: 6.5 Creedmoor
11/01/2015
JRHill85 wrote: For those loading with 142 SMK's how far are you guys jumping them? I can get good groups .02" off with Varget, but they're around 2625 if I remember correctly. Went .015" off with H4350 but can't really find anything worth duplicating. I've always found it pretty easy to find a good load until I ordered 800 142 SMK's ?. It seems like the faster I shoot them the more they open up
I jump my 142 SMKs .010" with great results in my .260 Rem and 6.5 Creedmoor. I jump 168 gr SMKs .010" in my .308 too.G
Guest
Guest
bornhunter04X65 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
11/03/2015
130 Berger Hybrids
42.8gr H4350
2.20 to ogive
2804 from 22" barrel
Shot out to 1570
Rate now:
RugbynutXPrivate
Rating: 3.0/5 this site
11 posts this site
Re: 6.5 Creedmoor
11/08/2015
(1 vote)
Tag for later
Rate now:
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
11/09/2015 Last edited 11/24/2015 by Brosome
26" Hawk Hill Marksmen Contour Barrel
140gr Hybrid - .02 off lands
42.3gr H4350
210m
2771 adv FPS (magnetospeed)
SD-7.4 / ES 20 over 20 shots
Rate now:
tacticalpanda
X48 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
395 posts this site
Re: 6.5 Creedmoor
11/15/2015
24" Ruger Precision rifle. Factory barrel.
42.5gr H4350
140gr Hornady A-max
Winchester Large Rifle Primer
Hornady Brass
2701 FPS
SD - 9
COAL 2.854
OGIVE 2.430
Rate now:
yfzjenXSergeant
Rating: 3.0/5 this site
149 posts this site
Re: 6.5 Creedmoor
11/15/2015
Looking for similar loads based on these things. Hawk Hill Marksmen barrel, 4350 powder, cci primers and hornady brass, and 140 Amax bullets. Looking for loads that have worked well in this barrel combination of components listed and OAL length they were blinded together at for COL.
6.5CM gun
Rate now:
Six5riflemanXSergeant
Rating: 3.0/5 this site
285 posts this site
Re: 6.5 Creedmoor
11/17/2015
I have a custom built 6.5 CM on a Rem action with a Krieger 22" Rem Varmint contour in a Manners EH 5 with chassis and magazine. I've got a NF 5-25x56 on top and I've really only shot factory loads in less than 1/2" moa. I do hand load but just got my dies for the 6.5. Does it matter a whole lot if I only have CCI BR2 and CCI 200 primers? I have Fed GM 215 and CCI Magnum primers for other calibers I load. I think I'm good on powders H4350, H4831sc, 8208xbr, Varget, Superformance, IMR4350-4831-3031, RL15. Question is I see most people using Fed GM210 but will the BR2 and 200 primers be fine?
Rate now:
Six5riflemanXSergeant
Rating: 3.0/5 this site
285 posts this site
Re: 6.5 Creedmoor
11/17/2015
Oh I forgot to mention the bullets I have are Barnes 100gr TTSX, Scirroco II 130, 140 Amax, 140 Berger Vld hunting, 140 Vld Hybrid Target, 140 Nos BT, 142 SMK. So really no shortage of bullets or powders. Only primers.
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
11/17/2015
Have used BR2, 210/210M with almost equal success, but on a steady diet of BR2's with shortage of 210M in San Antonio area. Any of the 140's and a starting load of 41.0 H4350 should get you going. Personally good results in 3 AR's and one bolt gun with Amax and 41.5 H4350. Easy on brass and runs between 2650 and 2800, from barrels between 21-26".
Rate now:
rjacobsXFirst Sergeant
Rating: 3.1/5 this site
1043 posts this site
Re: 6.5 Creedmoor
11/20/2015
Ill add mine because not many people seem to shoot Varget in 6.5creedmoor.
22" JP barrel, gas gun.
123g AMAX
39.8g Varget(node from 39.7-39.9)
CCI 200
Hornady brass neck sized to .288
5 shots
Avg 2877
SD 7.2
ES 16
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
11/24/2015
For me to touch the lands in my 6.5CM using 130 VLDs, I have to seat them to 2.885 COAL.
Does seem normal? It sure seems long to me.
Just checking.
Thanks,
CJ97
Rate now:
Why1504X66 MONTHS
Premium Member
Sergeant
Rating: 3.3/5 this site
430 posts this site
Re: 6.5 Creedmoor
11/26/2015
Rifle: AIAT
Barrel: MHS (Dave Tooley)
140 gr A-MAX
42.4gn H4350
OAL 2.800
shot one ragged hole by an old fat blind guy who had never shot that well.
Rate now:
lennyo3034XFirst Sergeant
Rating: 3.4/5 this site
1639 posts this site
Re: 6.5 Creedmoor
12/07/2015
41.8 grain of H4350 under a 139 Lapua Scenar loaded to .025" jump. Accuracy in the .3-.4 range out of a 26" barrel. SD under 10.
My velocity is around 2730, which is on the slow side. Do you guys think it's worth pursuing a higher node?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
12/07/2015
---------------------------------------------
--- lennyo3034 wrote:
41.8 grain of H4350 under a 139 Lapua Scenar loaded to .025" jump. Accuracy in the .3-.4 range out of a 26" barrel. SD under 10.
My velocity is around 2730, which is on the slow side. Do you guys think it's worth pursuing a higher node?
---------------------------------------------
42.4 h4350 is a pretty common node that should get you up to 2790 fps. I've personally never shot any H4350 under 42.2 grains. But I've gone WAY above that. And 42.4 to 42.6 usually is IT
Rate now:
Huckleberry75
XFirst Sergeant
Rating: 2.9/5 this site
1458 posts this site
Re: 6.5 Creedmoor
12/07/2015
Just for jollies, has anyone here tinkered with pointing the 130 hybrids and seeing what the improved BC is? I know in the 6.5saum (yes, I know, different animal) the 130 vld jumps up to a BC of 0.600. Curious to see if anyone has been bored enough to stroll down that rabbit hole. If it will get within sniffing distance of the 140 hybrid BC, and I can run it faster, it might be worth it for giggles.
Rate now:
1MoreARXSergeant
Rating: 3.0/5 this site
241 posts this site
Re: 6.5 Creedmoor
12/17/2015 Last edited 12/17/2015 by 1MoreAR
Accurate Ordnance build 6.5 CM with Rock Creek barrel at 24"
Berger 140 Gr. Hybrid seated .03 off land at 2.202" at ogive.
H4350 42.3 gr is the load for this rifle.
COAL 2.880 , I know it's long but it fit inside the magazine.
I did not chrono it yet, but should be right around 2,720-2,750 fps.
Rate now:
perazzisc3
XSergeant
Rating: 3.1/5 this site
426 posts this site
Re: 6.5 Creedmoor
01/01/2016
39.3 gr Varget under 120 gr Amax, 2900 fps 24" Criterion AR barrel
mag length
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/02/2016
Since you have 24" Criterion and Varget, try some 108 Lapua's or 107 Sierra's-if you have them laying around-under 39.7 Varget. Great load in 4 Creedmoors, light recoil, easy on brass, starts moving around in the wind at 500, but still very accurate at distance. Runs around 2975-3025, depending on barrel length.
Rate now:
jmk654XCorporal
Rating: 3.0/5 this site
56 posts this site
Re: 6.5 Creedmoor
01/03/2016 Last edited 01/03/2016 by jmk654
Anyone loaded the new ELD or ELD-X yet? Getting ready to reload doe first time and debating if the X is worth the extra money? I will be using H4350, BR-2 and Norma/Prime brass. What is a good starting load to start my ladder test at?
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
01/13/2016
130gr Hybrids
43.7gr H4350
Federal 210M
Hornady Brass
2.8" OAL
Running 2840fps out of a 22" Hawk Hill. Shot out to 1200yds so far and are spot on with minimal elevation dispersion.
Rate now:
Jake65mmXSergeant
Rating: 3.2/5 this site
495 posts this site
Re: 6.5 Creedmoor
01/17/2016 Last edited 01/17/2016 by Jake65mm
I just tried some out today in my 6.5 creedmore, 41.5 and 42 grains of h4350 Br-2 primers 2.850 oal shot in the 1's and low 2's. I will get velocity numbers later.
on a side note the factory 140 eld ammo wouldn't group very well at .5-.75 moa in my gun.
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
01/21/2016
> cavjock97 wrote:> For me to touch the lands in my 6.5CM using 130 VLDs, I have to seat them to 2.885 COAL.
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
01/22/2016
> craigos wrote:**> > cavjock97 wrote:**> > For me to touch the lands in my 6.5CM using 130 VLDs, I have to seat them to 2.885 COAL.Thanks for the data point. This load has been shooting really well, so I'll just leave it alone.
Rate now:
renomdXGunny Sergeant
Rating: 3.0/5 this site
815 posts this site
Re: 6.5 Creedmoor
01/22/2016 Last edited 01/23/2016 by renomd
Accuracy International AX308 2015
Graduous 6.5 CM barrel 26 inch, 1:8 twist (OTM tactical)
Hornady Brass, primer pocket uniformed, trimmed 1.916, stainless steel tumbled. Whidden FLS Bushing die, then expanded with expander mandrel die.
Primer: FG210M
Chronograph: prochrono for load development then magneto speed to confirm
Jam OGIVE lengths using a Hornady OAL gauge and bullet comparator inserts: L-scenar 139 gr 2.284, B-hybrid 140 gr 2.259, B-hybrid 130 gr 2.257.
Lapua Scenar 139 gr, 2.254 OGIVE, H4350 41.9 @ 2815 FPS (on average)
Berger Hybrid 140gr, 2.254 OGIVE (coincidence), H4350 42.6 @ 2805 FPS (below two targets are all 5 round groups....as you can see it's not a coincidence that these shoot 1/4-3/8 MOA). Seated 0.005 off the lands.
Berger 130 AR Hybrid, 2.242 OGIVE, H4350 43.5 gr @ 2899 FPS (mine as well say 2900) Below is the OCW test the 43.5 gr is the 5 round one hole target. It's not quite in the middle of the node where it's flat; but, it's between the lowest and highest so to me it's middle. It's loaded 0.015 off the lands... going with it.
Rate now:
WyomingShooterXSergeant
Rating: 3.0/5 this site
118 posts this site
Re: 6.5 Creedmoor
01/23/2016
(1 vote)
My 6.5 Creedmoor will be finished soon - Surgeon 591 action, Barlein barrel, MPA chassis, and Vortex Gen II Razor. I have 200 Hornady 143 ELD-X and 200 Berger 140 Hybrid bullets. What do y'all recommend for dies? I've never loaded for 6.5. Thanks in advance for your advice. From the Big Empty, ELN.
Premium Member
Sergeant
Rating: 3.1/5 this site
270 posts this site
Re: 6.5 Creedmoor
11/03/2015
130 Berger Hybrids
42.8gr H4350
2.20 to ogive
2804 from 22" barrel
Shot out to 1570
Rate now:
RugbynutXPrivate
Rating: 3.0/5 this site
11 posts this site
Re: 6.5 Creedmoor
11/08/2015
(1 vote)
Tag for later
Rate now:
BrosomeXCorporal
Rating: 3.0/5 this site
53 posts this site
Re: 6.5 Creedmoor
11/09/2015 Last edited 11/24/2015 by Brosome
26" Hawk Hill Marksmen Contour Barrel
140gr Hybrid - .02 off lands
42.3gr H4350
210m
2771 adv FPS (magnetospeed)
SD-7.4 / ES 20 over 20 shots
Rate now:
tacticalpanda
X48 MONTHS
Premium Member
Sergeant
Rating: 3.1/5 this site
395 posts this site
Re: 6.5 Creedmoor
11/15/2015
24" Ruger Precision rifle. Factory barrel.
42.5gr H4350
140gr Hornady A-max
Winchester Large Rifle Primer
Hornady Brass
2701 FPS
SD - 9
COAL 2.854
OGIVE 2.430
Rate now:
yfzjenXSergeant
Rating: 3.0/5 this site
149 posts this site
Re: 6.5 Creedmoor
11/15/2015
Looking for similar loads based on these things. Hawk Hill Marksmen barrel, 4350 powder, cci primers and hornady brass, and 140 Amax bullets. Looking for loads that have worked well in this barrel combination of components listed and OAL length they were blinded together at for COL.
6.5CM gun
Rate now:
Six5riflemanXSergeant
Rating: 3.0/5 this site
285 posts this site
Re: 6.5 Creedmoor
11/17/2015
I have a custom built 6.5 CM on a Rem action with a Krieger 22" Rem Varmint contour in a Manners EH 5 with chassis and magazine. I've got a NF 5-25x56 on top and I've really only shot factory loads in less than 1/2" moa. I do hand load but just got my dies for the 6.5. Does it matter a whole lot if I only have CCI BR2 and CCI 200 primers? I have Fed GM 215 and CCI Magnum primers for other calibers I load. I think I'm good on powders H4350, H4831sc, 8208xbr, Varget, Superformance, IMR4350-4831-3031, RL15. Question is I see most people using Fed GM210 but will the BR2 and 200 primers be fine?
Rate now:
Six5riflemanXSergeant
Rating: 3.0/5 this site
285 posts this site
Re: 6.5 Creedmoor
11/17/2015
Oh I forgot to mention the bullets I have are Barnes 100gr TTSX, Scirroco II 130, 140 Amax, 140 Berger Vld hunting, 140 Vld Hybrid Target, 140 Nos BT, 142 SMK. So really no shortage of bullets or powders. Only primers.
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
11/17/2015
Have used BR2, 210/210M with almost equal success, but on a steady diet of BR2's with shortage of 210M in San Antonio area. Any of the 140's and a starting load of 41.0 H4350 should get you going. Personally good results in 3 AR's and one bolt gun with Amax and 41.5 H4350. Easy on brass and runs between 2650 and 2800, from barrels between 21-26".
Rate now:
rjacobsXFirst Sergeant
Rating: 3.1/5 this site
1043 posts this site
Re: 6.5 Creedmoor
11/20/2015
Ill add mine because not many people seem to shoot Varget in 6.5creedmoor.
22" JP barrel, gas gun.
123g AMAX
39.8g Varget(node from 39.7-39.9)
CCI 200
Hornady brass neck sized to .288
5 shots
Avg 2877
SD 7.2
ES 16
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
11/24/2015
For me to touch the lands in my 6.5CM using 130 VLDs, I have to seat them to 2.885 COAL.
Does seem normal? It sure seems long to me.
Just checking.
Thanks,
CJ97
Rate now:
Why1504X66 MONTHS
Premium Member
Sergeant
Rating: 3.3/5 this site
430 posts this site
Re: 6.5 Creedmoor
11/26/2015
Rifle: AIAT
Barrel: MHS (Dave Tooley)
140 gr A-MAX
42.4gn H4350
OAL 2.800
shot one ragged hole by an old fat blind guy who had never shot that well.
Rate now:
lennyo3034XFirst Sergeant
Rating: 3.4/5 this site
1639 posts this site
Re: 6.5 Creedmoor
12/07/2015
41.8 grain of H4350 under a 139 Lapua Scenar loaded to .025" jump. Accuracy in the .3-.4 range out of a 26" barrel. SD under 10.
My velocity is around 2730, which is on the slow side. Do you guys think it's worth pursuing a higher node?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
12/07/2015
---------------------------------------------
--- lennyo3034 wrote:
41.8 grain of H4350 under a 139 Lapua Scenar loaded to .025" jump. Accuracy in the .3-.4 range out of a 26" barrel. SD under 10.
My velocity is around 2730, which is on the slow side. Do you guys think it's worth pursuing a higher node?
---------------------------------------------
42.4 h4350 is a pretty common node that should get you up to 2790 fps. I've personally never shot any H4350 under 42.2 grains. But I've gone WAY above that. And 42.4 to 42.6 usually is IT
Rate now:
Huckleberry75
XFirst Sergeant
Rating: 2.9/5 this site
1458 posts this site
Re: 6.5 Creedmoor
12/07/2015
Just for jollies, has anyone here tinkered with pointing the 130 hybrids and seeing what the improved BC is? I know in the 6.5saum (yes, I know, different animal) the 130 vld jumps up to a BC of 0.600. Curious to see if anyone has been bored enough to stroll down that rabbit hole. If it will get within sniffing distance of the 140 hybrid BC, and I can run it faster, it might be worth it for giggles.
Rate now:
1MoreARXSergeant
Rating: 3.0/5 this site
241 posts this site
Re: 6.5 Creedmoor
12/17/2015 Last edited 12/17/2015 by 1MoreAR
Accurate Ordnance build 6.5 CM with Rock Creek barrel at 24"
Berger 140 Gr. Hybrid seated .03 off land at 2.202" at ogive.
H4350 42.3 gr is the load for this rifle.
COAL 2.880 , I know it's long but it fit inside the magazine.
I did not chrono it yet, but should be right around 2,720-2,750 fps.
Rate now:
perazzisc3
XSergeant
Rating: 3.1/5 this site
426 posts this site
Re: 6.5 Creedmoor
01/01/2016
39.3 gr Varget under 120 gr Amax, 2900 fps 24" Criterion AR barrel
mag length
Rate now:
bobketxXGunny Sergeant
Rating: 3.3/5 this site
744 posts this site
Re: 6.5 Creedmoor
01/02/2016
Since you have 24" Criterion and Varget, try some 108 Lapua's or 107 Sierra's-if you have them laying around-under 39.7 Varget. Great load in 4 Creedmoors, light recoil, easy on brass, starts moving around in the wind at 500, but still very accurate at distance. Runs around 2975-3025, depending on barrel length.
Rate now:
jmk654XCorporal
Rating: 3.0/5 this site
56 posts this site
Re: 6.5 Creedmoor
01/03/2016 Last edited 01/03/2016 by jmk654
Anyone loaded the new ELD or ELD-X yet? Getting ready to reload doe first time and debating if the X is worth the extra money? I will be using H4350, BR-2 and Norma/Prime brass. What is a good starting load to start my ladder test at?
Rate now:
NGCSUGrad09
XSergeant
Rating: 3.8/5 this site
265 posts this site
Re: 6.5 Creedmoor
01/13/2016
130gr Hybrids
43.7gr H4350
Federal 210M
Hornady Brass
2.8" OAL
Running 2840fps out of a 22" Hawk Hill. Shot out to 1200yds so far and are spot on with minimal elevation dispersion.
Rate now:
Jake65mmXSergeant
Rating: 3.2/5 this site
495 posts this site
Re: 6.5 Creedmoor
01/17/2016 Last edited 01/17/2016 by Jake65mm
I just tried some out today in my 6.5 creedmore, 41.5 and 42 grains of h4350 Br-2 primers 2.850 oal shot in the 1's and low 2's. I will get velocity numbers later.
on a side note the factory 140 eld ammo wouldn't group very well at .5-.75 moa in my gun.
jmk654 wrote:
Anyone loaded the new ELD or ELD-X yet? Getting ready to reload doe first time and debating if the X is worth the extra money? I will be using H4350, BR-2 and Norma/Prime brass. What is a good starting load to start my ladder test at?
Rate now: Anyone loaded the new ELD or ELD-X yet? Getting ready to reload doe first time and debating if the X is worth the extra money? I will be using H4350, BR-2 and Norma/Prime brass. What is a good starting load to start my ladder test at?
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
01/21/2016
> cavjock97 wrote:> For me to touch the lands in my 6.5CM using 130 VLDs, I have to seat them to 2.885 COAL.
Does seem normal? It sure seems long to me.
Just checking.
Thanks,
CJ97
Mine is 2.890Just checking.
Thanks,
CJ97
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
01/22/2016
> craigos wrote:**> > cavjock97 wrote:**> > For me to touch the lands in my 6.5CM using 130 VLDs, I have to seat them to 2.885 COAL.
Does seem normal? It sure seems long to me.
Just checking.
Thanks,
CJ97
Mine is 2.890Just checking.
Thanks,
CJ97
Rate now:
renomdXGunny Sergeant
Rating: 3.0/5 this site
815 posts this site
Re: 6.5 Creedmoor
01/22/2016 Last edited 01/23/2016 by renomd
Accuracy International AX308 2015
Graduous 6.5 CM barrel 26 inch, 1:8 twist (OTM tactical)
Hornady Brass, primer pocket uniformed, trimmed 1.916, stainless steel tumbled. Whidden FLS Bushing die, then expanded with expander mandrel die.
Primer: FG210M
Chronograph: prochrono for load development then magneto speed to confirm
Jam OGIVE lengths using a Hornady OAL gauge and bullet comparator inserts: L-scenar 139 gr 2.284, B-hybrid 140 gr 2.259, B-hybrid 130 gr 2.257.
Lapua Scenar 139 gr, 2.254 OGIVE, H4350 41.9 @ 2815 FPS (on average)
Berger Hybrid 140gr, 2.254 OGIVE (coincidence), H4350 42.6 @ 2805 FPS (below two targets are all 5 round groups....as you can see it's not a coincidence that these shoot 1/4-3/8 MOA). Seated 0.005 off the lands.
Berger 130 AR Hybrid, 2.242 OGIVE, H4350 43.5 gr @ 2899 FPS (mine as well say 2900) Below is the OCW test the 43.5 gr is the 5 round one hole target. It's not quite in the middle of the node where it's flat; but, it's between the lowest and highest so to me it's middle. It's loaded 0.015 off the lands... going with it.
Rate now:
WyomingShooterXSergeant
Rating: 3.0/5 this site
118 posts this site
Re: 6.5 Creedmoor
01/23/2016
(1 vote)
My 6.5 Creedmoor will be finished soon - Surgeon 591 action, Barlein barrel, MPA chassis, and Vortex Gen II Razor. I have 200 Hornady 143 ELD-X and 200 Berger 140 Hybrid bullets. What do y'all recommend for dies? I've never loaded for 6.5. Thanks in advance for your advice. From the Big Empty, ELN.
G
Guest
Guest
realtallwolf1
XCorporal
Rating: 3.0/5 this site
62 posts this site
Re: 6.5 Creedmoor
01/25/2016
Rate now:
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
01/30/2016 Last edited 01/30/2016 by craigos
I found my node for the 130 berger target @ Ogive 2.202, Br2 primers, H brass between 43.2 and 43.6 (I loaded up every 0.2 gr) but even across my 8 loads (42.6 to 43.8) it was very flat. Am shooting 24" bartlein on my new custom GAP bolt gun based on a tempest.
So going to investigate more between 43.3 to 43.5 in .1 increments ... and then play with bullet seating. Got some 130 berger Ar hybrids coming ....
> renomd wrote:> Accuracy International AX308 2015
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
02/04/2016
Just finished testing the new led match loaded from 42.0, 42.2, 42.4, 42.5 42.6, 42.8 4350
The 42.0 and 42.5 shot the best, about 5/8th each.
Loaded all 20 off the lands.
This same rifle shoots my Berger load 20 off with the 42.5 at 3/8th inch so I am going to go with the 42.5 and play with the al a bit to see how much I can tighten the load up.
Rate now:
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
02/06/2016
Taking a friend out shooting next week and he bought a ruger precision rifle in 6.5CM. Any one with some good loads for the Ruger barrel and the LRI barrel (A Max setup) using a 140 ELD?
Rate now:
Alex126XSergeant
Rating: 3.1/5 this site
145 posts this site
Re: 6.5 Creedmoor
02/09/2016
I found my max OAL using the Hornady tool to be 2.241" to ogive using Berger 140 hybrids.
Started load workup at 2.22" to ogive with 40gr of H4350, going up in .5gr increments to 41.5.
Does this sound right? This is my first time loading precision rounds and I want to get it right.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
02/20/2016
6.5 Gap Crusader. 26" 1:8 Krieger. 140 hybrid with 42.6 H4350 at 2.176 to ogive with 1x Hornady brass. Fl resized with a Redding Type S and a .289" bushing. Shoulder set back 3 thousandths.
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
XCorporal
Rating: 3.0/5 this site
62 posts this site
Re: 6.5 Creedmoor
01/25/2016
Rate now:
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
01/30/2016 Last edited 01/30/2016 by craigos
I found my node for the 130 berger target @ Ogive 2.202, Br2 primers, H brass between 43.2 and 43.6 (I loaded up every 0.2 gr) but even across my 8 loads (42.6 to 43.8) it was very flat. Am shooting 24" bartlein on my new custom GAP bolt gun based on a tempest.
So going to investigate more between 43.3 to 43.5 in .1 increments ... and then play with bullet seating. Got some 130 berger Ar hybrids coming ....
> renomd wrote:> Accuracy International AX308 2015
Graduous 6.5 CM barrel 26 inch, 1:8 twist (OTM tactical)
Hornady Brass, primer pocket uniformed, trimmed 1.916, stainless steel tumbled. Whidden FLS Bushing die, then expanded with expander mandrel die.
Primer: FG210M
Chronograph: prochrono for load development then magneto speed to confirm
Jam OGIVE lengths using a Hornady OAL gauge and bullet comparator inserts: L-scenar 139 gr 2.284, B-hybrid 140 gr 2.259, B-hybrid 130 gr 2.257.
Lapua Scenar 139 gr, 2.254 OGIVE, H4350 41.9 @ 2815 FPS (on average)
Berger Hybrid 140gr, 2.254 OGIVE (coincidence), H4350 42.6 @ 2805 FPS (below two targets are all 5 round groups....as you can see it's not a coincidence that these shoot 1/4-3/8 MOA). Seated 0.005 off the lands.
Hornady Brass, primer pocket uniformed, trimmed 1.916, stainless steel tumbled. Whidden FLS Bushing die, then expanded with expander mandrel die.
Primer: FG210M
Chronograph: prochrono for load development then magneto speed to confirm
Jam OGIVE lengths using a Hornady OAL gauge and bullet comparator inserts: L-scenar 139 gr 2.284, B-hybrid 140 gr 2.259, B-hybrid 130 gr 2.257.
Lapua Scenar 139 gr, 2.254 OGIVE, H4350 41.9 @ 2815 FPS (on average)
Berger Hybrid 140gr, 2.254 OGIVE (coincidence), H4350 42.6 @ 2805 FPS (below two targets are all 5 round groups....as you can see it's not a coincidence that these shoot 1/4-3/8 MOA). Seated 0.005 off the lands.
Berger 130 AR Hybrid, 2.242 OGIVE, H4350 43.5 gr @ 2899 FPS (mine as well say 2900) Below is the OCW test the 43.5 gr is the 5 round one hole target. It's not quite in the middle of the node where it's flat; but, it's between the lowest and highest so to me it's middle. It's loaded 0.015 off the lands... going with it.
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
02/04/2016
Just finished testing the new led match loaded from 42.0, 42.2, 42.4, 42.5 42.6, 42.8 4350
The 42.0 and 42.5 shot the best, about 5/8th each.
Loaded all 20 off the lands.
This same rifle shoots my Berger load 20 off with the 42.5 at 3/8th inch so I am going to go with the 42.5 and play with the al a bit to see how much I can tighten the load up.
Rate now:
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
02/06/2016
Taking a friend out shooting next week and he bought a ruger precision rifle in 6.5CM. Any one with some good loads for the Ruger barrel and the LRI barrel (A Max setup) using a 140 ELD?
Rate now:
Alex126XSergeant
Rating: 3.1/5 this site
145 posts this site
Re: 6.5 Creedmoor
02/09/2016
I found my max OAL using the Hornady tool to be 2.241" to ogive using Berger 140 hybrids.
Started load workup at 2.22" to ogive with 40gr of H4350, going up in .5gr increments to 41.5.
Does this sound right? This is my first time loading precision rounds and I want to get it right.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
02/20/2016
6.5 Gap Crusader. 26" 1:8 Krieger. 140 hybrid with 42.6 H4350 at 2.176 to ogive with 1x Hornady brass. Fl resized with a Redding Type S and a .289" bushing. Shoulder set back 3 thousandths.
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
G
Guest
Guest
nilescoyote
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
02/23/2016
(1 vote)
I was at my locals Cabela's with a coupon (dangerous thing) a few weeks ago and found they had some of each so I brought them home for testing.
Left to right:
130 Berger AR Hybrid, 140 Hornady A-Max, 140 Hornady ELD, 143 Hornady ELD-X, 140 Berger Hybrid and 139 Lapua Scenar.
Rate now:
NemesisGigantes
XPrivate
Rating: 3.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
02/27/2016
(3 votes)
Bought a Ruger Precision Rifle in 6.5 Creedmoor last fall. Shot a superb 10 shot group with 140 SMK's the first time out and have been trying to reproduce it ever since. Finally hit the magic combo today.
139 Scenar
42.0gr H4350 produces 2820fps with consistent velocities
.025" off the lands.
The load looks more like a shotgun pattern at 42.5gr
Ten fit easily under a dime at 42.0gr
May drop to 41.8 or so in the future as ambient was around 60 degree F
Try this if you are having the same experience....what a relief to fine THE load.
Rate now:
kjeffXPrivate
Rating: 0.0/5 this site
7 posts this site
Re: 6.5 Creedmoor
02/29/2016
I just bought a 6.5 Howa Gameking and I am going to start reloading. This is super helpful! Just wondering, measuring to ogive vs COAL, is there a huge difference(I know there is some depending on the meplat) if I use the same grain, brand and model bullet?
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
02/29/2016
(1 vote)
Rate now:
PBinWAXSergeant
Rating: 3.1/5 this site
235 posts this site
Re: 6.5 Creedmoor
02/29/2016
Tag
Rate now:
TheHelmsmanXPrivate
Rating: 0.0/5 this site
12 posts this site
Re: 6.5 Creedmoor
03/01/2016
Tag
Rate now:
dejahboiXPrivate
Rating: 3.1/5 this site
26 posts this site
Re: 6.5 Creedmoor
03/10/2016
tag
Rate now:
mkf350XCorporal
Rating: 3.1/5 this site
53 posts this site
Re: 6.5 Creedmoor
03/30/2016
tag
Rate now:
cecchino76XFirst Sergeant
Rating: 3.0/5 this site
1682 posts this site
Re: 6.5 Creedmoor
04/01/2016
Anybody tried the newer IMR enduron technology 4166 with green laeble yet?
Rate now:
Rob01
XModerator
Rating: 3.8/5 this site
11458 posts this site
Re: 6.5 Creedmoor
04/02/2016
Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
Rate now:
cecchino76XFirst Sergeant
Rating: 3.0/5 this site
1682 posts this site
Re: 6.5 Creedmoor
04/02/2016
swhiteh3XSergeant
Rating: 3.0/5 this site
348 posts this site
Re: 6.5 Creedmoor
04/06/2016
Rate now:
Rob01
XModerator
Rating: 3.8/5 this site
11458 posts this site
Re: 6.5 Creedmoor
04/06/2016
hodgdon.com/PDF/Burn%20Rates%20-%202015-2016.pdf
Rate now:
BoltpupXSergeant
Rating: 3.2/5 this site
311 posts this site
Re: 6.5 Creedmoor
04/06/2016
---------------------------------------------
--- Rob01 wrote:
Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
---------------------------------------------
Ive gotten the exact same results across summer and winter temp ranges using 4451 in place of H4350. I use roughly 1 grain more powder to achieve the same velocity across the board of temps. I was trying to keep a lid on it so it doesn't get sold out everywhere but it's an amazing powder for the 6.5 Creed, in my experience. Multiple 1/4 MOA groups at 100 and lots of consistent impacts out to 1k.
Rate now:
Jibnast
XSergeant
Rating: 3.4/5 this site
301 posts this site
Re: 6.5 Creedmoor
04/09/2016
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
04/10/2016
Rate now:
AlderleetXGunny Sergeant
Rating: 3.3/5 this site
952 posts this site
Re: 6.5 Creedmoor
04/10/2016
(1 vote)
Tried both the H4350 and IMR 4451. The 4451 blew H4350 away today. Less vertical dispersion, less fouling, less cat pee smell.
Ruger Precision Rifle 6.5 Creedmoor 24" (factory)
Hornady 6.5 Creedmoor Brass (Fired 1x, trimmed 1.917) (full length Forster BR die)
Winchester LR primers (seated on forster coax primer seater)
40.8gr IMR 4451
Hornady ELD-M 140gr bullet
COAL: 2.819 (using forster ultra micrometer seater die)
5-shot group: .29"
Rate now:
10ring1XSergeant
Rating: 3.1/5 this site
187 posts this site
Re: 6.5 Creedmoor
04/12/2016
Tag
Rate now:
Brent1969XPrivate
Rating: 0.0/5 this site
9 posts this site
Re: 6.5 Creedmoor
04/13/2016
Rate now:
jeff1383XGunny Sergeant
Rating: 3.3/5 this site
664 posts this site
Re: 6.5 Creedmoor
04/14/2016
What's your MV?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/17/2016
(1 vote)
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/17/2016
XFirst Sergeant
Rating: 3.6/5 this site
4209 posts this site
Re: 6.5 Creedmoor
02/23/2016
(1 vote)
I was at my locals Cabela's with a coupon (dangerous thing) a few weeks ago and found they had some of each so I brought them home for testing.
Left to right:
130 Berger AR Hybrid, 140 Hornady A-Max, 140 Hornady ELD, 143 Hornady ELD-X, 140 Berger Hybrid and 139 Lapua Scenar.
Rate now:
NemesisGigantes
XPrivate
Rating: 3.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
02/27/2016
(3 votes)
Bought a Ruger Precision Rifle in 6.5 Creedmoor last fall. Shot a superb 10 shot group with 140 SMK's the first time out and have been trying to reproduce it ever since. Finally hit the magic combo today.
139 Scenar
42.0gr H4350 produces 2820fps with consistent velocities
.025" off the lands.
The load looks more like a shotgun pattern at 42.5gr
Ten fit easily under a dime at 42.0gr
May drop to 41.8 or so in the future as ambient was around 60 degree F
Try this if you are having the same experience....what a relief to fine THE load.
Rate now:
kjeffXPrivate
Rating: 0.0/5 this site
7 posts this site
Re: 6.5 Creedmoor
02/29/2016
I just bought a 6.5 Howa Gameking and I am going to start reloading. This is super helpful! Just wondering, measuring to ogive vs COAL, is there a huge difference(I know there is some depending on the meplat) if I use the same grain, brand and model bullet?
Rate now:
DarksideSix
XFirst Sergeant
Rating: 3.6/5 this site
2199 posts this site
Re: 6.5 Creedmoor
02/29/2016
(1 vote)
kjeff wrote:
I just bought a 6.5 Howa Gameking and I am going to start reloading. This is super helpful! Just wondering, measuring to ogive vs COAL, is there a huge difference(I know there is some depending on the meplat) if I use the same grain, brand and model bullet?
Always load to the ogive. Your COAL will fluctuate here and there do to the difference in bullet lots.I just bought a 6.5 Howa Gameking and I am going to start reloading. This is super helpful! Just wondering, measuring to ogive vs COAL, is there a huge difference(I know there is some depending on the meplat) if I use the same grain, brand and model bullet?
Rate now:
PBinWAXSergeant
Rating: 3.1/5 this site
235 posts this site
Re: 6.5 Creedmoor
02/29/2016
Tag
Rate now:
TheHelmsmanXPrivate
Rating: 0.0/5 this site
12 posts this site
Re: 6.5 Creedmoor
03/01/2016
Tag
Rate now:
dejahboiXPrivate
Rating: 3.1/5 this site
26 posts this site
Re: 6.5 Creedmoor
03/10/2016
tag
Rate now:
mkf350XCorporal
Rating: 3.1/5 this site
53 posts this site
Re: 6.5 Creedmoor
03/30/2016
tag
Rate now:
cecchino76XFirst Sergeant
Rating: 3.0/5 this site
1682 posts this site
Re: 6.5 Creedmoor
04/01/2016
Anybody tried the newer IMR enduron technology 4166 with green laeble yet?
Rate now:
Rob01
XModerator
Rating: 3.8/5 this site
11458 posts this site
Re: 6.5 Creedmoor
04/02/2016
Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
Rate now:
cecchino76XFirst Sergeant
Rating: 3.0/5 this site
1682 posts this site
Re: 6.5 Creedmoor
04/02/2016
Rob01 wrote: Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
Thanks Rob
I'll see if I can get my hands on it
Nice to hear from you again ?
Rate now: Thanks Rob
I'll see if I can get my hands on it
Nice to hear from you again ?
swhiteh3XSergeant
Rating: 3.0/5 this site
348 posts this site
Re: 6.5 Creedmoor
04/06/2016
DarksideSix wrote:
What he said!kjeff wrote:
I just bought a 6.5 Howa Gameking and I am going to start reloading. This is super helpful! Just wondering, measuring to ogive vs COAL, is there a huge difference(I know there is some depending on the meplat) if I use the same grain, brand and model bullet?
Always load to the ogive. Your COAL will fluctuate here and there do to the difference in bullet lots.I just bought a 6.5 Howa Gameking and I am going to start reloading. This is super helpful! Just wondering, measuring to ogive vs COAL, is there a huge difference(I know there is some depending on the meplat) if I use the same grain, brand and model bullet?
Rate now:
Rob01
XModerator
Rating: 3.8/5 this site
11458 posts this site
Re: 6.5 Creedmoor
04/06/2016
jhayesvw wrote:
Is the new Enduron IMR 4451 the same burn rate as the old 4451?
Not sure about compared to the old one but the new 4451 is right with H4350. Is the new Enduron IMR 4451 the same burn rate as the old 4451?
hodgdon.com/PDF/Burn%20Rates%20-%202015-2016.pdf
Rate now:
BoltpupXSergeant
Rating: 3.2/5 this site
311 posts this site
Re: 6.5 Creedmoor
04/06/2016
---------------------------------------------
--- Rob01 wrote:
Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
---------------------------------------------
Ive gotten the exact same results across summer and winter temp ranges using 4451 in place of H4350. I use roughly 1 grain more powder to achieve the same velocity across the board of temps. I was trying to keep a lid on it so it doesn't get sold out everywhere but it's an amazing powder for the 6.5 Creed, in my experience. Multiple 1/4 MOA groups at 100 and lots of consistent impacts out to 1k.
Rate now:
Jibnast
XSergeant
Rating: 3.4/5 this site
301 posts this site
Re: 6.5 Creedmoor
04/09/2016
Boltpup wrote:
--- Rob01 wrote:
Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
Ive gotten the exact same results across summer and winter temp ranges using 4451 in place of H4350. I use roughly 1 grain more powder to achieve the same velocity across the board of temps. I was trying to keep a lid on it so it doesn't get sold out everywhere but it's an amazing powder for the 6.5 Creed, in my experience. Multiple 1/4 MOA groups at 100 and lots of consistent impacts out to 1k.
Using IMR 4451 and 18 degrees vs 75 degrees I saw a shift of 8 FPS so I'm willing to say it is pretty temp stable.--- Rob01 wrote:
Try the 4451. It's more around the H4350 burn rate. After reading reports I got 16 pounds coming in.
Ive gotten the exact same results across summer and winter temp ranges using 4451 in place of H4350. I use roughly 1 grain more powder to achieve the same velocity across the board of temps. I was trying to keep a lid on it so it doesn't get sold out everywhere but it's an amazing powder for the 6.5 Creed, in my experience. Multiple 1/4 MOA groups at 100 and lots of consistent impacts out to 1k.
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
04/10/2016
Aimsmall55 wrote: 6.5 Gap Crusader. 26" 1:8 Krieger. 140 hybrid with 42.6 H4350 at 2.176 to ogive with 1x Hornady brass. Fl resized with a Redding Type S and a .289" bushing. Shoulder set back 3 thousandths.
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
You were scared to take that 5th shot, weren't you?
Rate now:
AlderleetXGunny Sergeant
Rating: 3.3/5 this site
952 posts this site
Re: 6.5 Creedmoor
04/10/2016
(1 vote)
Tried both the H4350 and IMR 4451. The 4451 blew H4350 away today. Less vertical dispersion, less fouling, less cat pee smell.
Ruger Precision Rifle 6.5 Creedmoor 24" (factory)
Hornady 6.5 Creedmoor Brass (Fired 1x, trimmed 1.917) (full length Forster BR die)
Winchester LR primers (seated on forster coax primer seater)
40.8gr IMR 4451
Hornady ELD-M 140gr bullet
COAL: 2.819 (using forster ultra micrometer seater die)
5-shot group: .29"
Rate now:
10ring1XSergeant
Rating: 3.1/5 this site
187 posts this site
Re: 6.5 Creedmoor
04/12/2016
Tag
Rate now:
Brent1969XPrivate
Rating: 0.0/5 this site
9 posts this site
Re: 6.5 Creedmoor
04/13/2016
Flyboy22x wrote:
What app are you using here?Aimsmall55 wrote: 6.5 Gap Crusader. 26" 1:8 Krieger. 140 hybrid with 42.6 H4350 at 2.176 to ogive with 1x Hornady brass. Fl resized with a Redding Type S and a .289" bushing. Shoulder set back 3 thousandths.
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
You were scared to take that 5th shot, weren't you?
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
You were scared to take that 5th shot, weren't you?
Rate now:
jeff1383XGunny Sergeant
Rating: 3.3/5 this site
664 posts this site
Re: 6.5 Creedmoor
04/14/2016
What's your MV?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/17/2016
(1 vote)
Flyboy22x wrote:
Lmao... EXACTLY ?Aimsmall55 wrote: 6.5 Gap Crusader. 26" 1:8 Krieger. 140 hybrid with 42.6 H4350 at 2.176 to ogive with 1x Hornady brass. Fl resized with a Redding Type S and a .289" bushing. Shoulder set back 3 thousandths.
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
You were scared to take that 5th shot, weren't you?
4 shots at 104 yards.
[IMG2=JSON]{"alt":" photo 6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png","data-align":"none","data-size":"full","src":"http:\/\/i1355.photobucket.com\/albums\/q715\/Todd_Ellis\/Mobile%20Uploads\/2016-02\/6077E981-418B-436D-8AFE-BF9F0E8C0190_zpsovrxvcqi.png"}[/IMG2]
You were scared to take that 5th shot, weren't you?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/17/2016
jeff1383 wrote:
What's your MV?
Jeff, it's about 2810 fpsWhat's your MV?
G
Guest
Guest
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
04/19/2016 Last edited 04/19/2016 by Flyboy22x
Thus far on my AXMC with 26" Bartlein barrel, I've gotten these ladder test results using H4350, BR2 Primers, Prime (Norma) brass, and Berger 130 AR Hybrids @ 300 yards:
I really haven't seen much in the way of pressure, even at 44.2 grains. I loaded up another ladder from 44.0 to 44.9 in .1 increments but haven't shot it yet... is that too hot?? My ladder test indicates maybe there is another node in the low 44's... it would be nice to have more data.
I only chrono'd 43.4gr at 2830 fps, which seems slow for a 26" barrel compared to many others on here. Is this possibly due to barrel break-in? My target velocity for 130 Hybrids is about 2900 fps, though now I'm nervous to push past 44 grains since nobody else seems to be going that high.
Rate now:
WyomingShooterXSergeant
Rating: 3.0/5 this site
118 posts this site
Re: 6.5 Creedmoor
04/25/2016
Test date: 04/25/16
Temp: 40 degrees F
Bartlein medium palma 26" barrel
Hornady brass - once fired
Fed 210M primers
Berger 140 hybrid bullet
42.4 grains H4350
10 shots over Magnetospeed V3
Avg velocity = 2826 fps
SD = 9.4
Max = 2841 fps
Min = 2817
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/27/2016
I shot this the other day. 140 ELD M at 2.217 to ogive. 210 m , Hornady brass , 42.6 H4350. 2805 fps average.
Only had 100 yards but something tells me it's going to be a winner. .09 moa
[IMG2=JSON]{"alt":" photo F24343AE-6DA5-4837-9570-A5BCCB79BD9E_zpsfrwx5zga.jpg","data-align":"none","data-size":"full","src":"http:\/\/i802.photobucket.com\/albums\/yy305\/stewartellis3007\/F24343AE-6DA5-4837-9570-A5BCCB79BD9E_zpsfrwx5zga.jpg"}[/IMG2]
Rate now:
jeff1383XGunny Sergeant
Rating: 3.3/5 this site
664 posts this site
Re: 6.5 Creedmoor
04/28/2016
Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
Rate now:
surgeon7X91 MONTHS
Premium Member
Private
Rating: 3.0/5 this site
45 posts this site
Re: 6.5 Creedmoor
04/29/2016
Tag
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
04/29/2016
I've been shooting this exact load except with BR2 primers and Prime brass. What kind of groups are you getting?
Rate now:
jeff1383XGunny Sergeant
Rating: 3.3/5 this site
664 posts this site
Re: 6.5 Creedmoor
05/01/2016 Last edited 05/01/2016 by jeff1383
Consistent 1/2 MOA with the occasional one holer. Really don't spend much time shooting inside 300 yards. Load has performed very well for me.
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
05/01/2016
5 shot group at 800 came out to 6" even with the horizontal "flyer" that was probably my fault. Pretty happy with that so far.
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
04/19/2016 Last edited 04/19/2016 by Flyboy22x
Thus far on my AXMC with 26" Bartlein barrel, I've gotten these ladder test results using H4350, BR2 Primers, Prime (Norma) brass, and Berger 130 AR Hybrids @ 300 yards:
I really haven't seen much in the way of pressure, even at 44.2 grains. I loaded up another ladder from 44.0 to 44.9 in .1 increments but haven't shot it yet... is that too hot?? My ladder test indicates maybe there is another node in the low 44's... it would be nice to have more data.
I only chrono'd 43.4gr at 2830 fps, which seems slow for a 26" barrel compared to many others on here. Is this possibly due to barrel break-in? My target velocity for 130 Hybrids is about 2900 fps, though now I'm nervous to push past 44 grains since nobody else seems to be going that high.
Rate now:
WyomingShooterXSergeant
Rating: 3.0/5 this site
118 posts this site
Re: 6.5 Creedmoor
04/25/2016
Test date: 04/25/16
Temp: 40 degrees F
Bartlein medium palma 26" barrel
Hornady brass - once fired
Fed 210M primers
Berger 140 hybrid bullet
42.4 grains H4350
10 shots over Magnetospeed V3
Avg velocity = 2826 fps
SD = 9.4
Max = 2841 fps
Min = 2817
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
04/27/2016
I shot this the other day. 140 ELD M at 2.217 to ogive. 210 m , Hornady brass , 42.6 H4350. 2805 fps average.
Only had 100 yards but something tells me it's going to be a winner. .09 moa
[IMG2=JSON]{"alt":" photo F24343AE-6DA5-4837-9570-A5BCCB79BD9E_zpsfrwx5zga.jpg","data-align":"none","data-size":"full","src":"http:\/\/i802.photobucket.com\/albums\/yy305\/stewartellis3007\/F24343AE-6DA5-4837-9570-A5BCCB79BD9E_zpsfrwx5zga.jpg"}[/IMG2]
Rate now:
jeff1383XGunny Sergeant
Rating: 3.3/5 this site
664 posts this site
Re: 6.5 Creedmoor
04/28/2016
Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
Rate now:
surgeon7X91 MONTHS
Premium Member
Private
Rating: 3.0/5 this site
45 posts this site
Re: 6.5 Creedmoor
04/29/2016
Tag
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
04/29/2016
jeff1383 wrote:
Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
I've been shooting this exact load except with BR2 primers and Prime brass. What kind of groups are you getting?
Rate now:
jeff1383XGunny Sergeant
Rating: 3.3/5 this site
664 posts this site
Re: 6.5 Creedmoor
05/01/2016 Last edited 05/01/2016 by jeff1383
Consistent 1/2 MOA with the occasional one holer. Really don't spend much time shooting inside 300 yards. Load has performed very well for me.
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
05/01/2016
jeff1383 wrote:
Consistent 1/2 MOA with the occasional one holer. Really don't spend much time shooting inside 300 yards. Load has performed very well for me.
I'm seeing about the same, though my velocity is about 50 fps slower (26" bbl). Not sure about why that is, unless Prime is a roomier brass case.Consistent 1/2 MOA with the occasional one holer. Really don't spend much time shooting inside 300 yards. Load has performed very well for me.
5 shot group at 800 came out to 6" even with the horizontal "flyer" that was probably my fault. Pretty happy with that so far.
G
Guest
Guest
EriicXPrivate
Rating: 0.0/5 this site
11 posts this site
Re: 6.5 Creedmoor
05/03/2016
Tag
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
05/07/2016
Rob any report back on the new powder?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
05/10/2016
(1 vote)
140 ELD M @ 2.217 to ogive
Virgin Hornady brass
42.6 H4350
FGM210m
4 shots at 200 yards
[IMG2=JSON]{"alt":" photo 58994AA1-E325-4D35-B0B8-0E90C4F2DDE7_zpsihkfwk3s.png","data-align":"none","data-size":"full","src":"http:\/\/i802.photobucket.com\/albums\/yy305\/stewartellis3007\/58994AA1-E325-4D35-B0B8-0E90C4F2DDE7_zpsihkfwk3s.png"}[/IMG2]
Rate now:
jomo34XPrivate
Rating: 0.0/5 this site
3 posts this site
Re: 6.5 Creedmoor
05/11/2016
Tag
Rate now:
BLS27XSergeant
Rating: 3.1/5 this site
186 posts this site
Re: 6.5 Creedmoor
05/13/2016
Ruger Precision Rifle
140g Hornady HPBT
40.6 (2700fps 2.8 SD ) & 41.8 (2798fps 6.6 SD) - Reloader 17
Winchester Brass (annealed, FL resized)
CCI 200 Primers
Both loads cut a nice 3/8 hole @ 100 yards
Rate now:
straightandtrueX27 MONTHS
Premium Member
Corporal
Rating: 3.3/5 this site
93 posts this site
Re: 6.5 Creedmoor
05/16/2016 Last edited 05/16/2016 by straightandtrue
(1 vote)
Ok Ladies and Gentleman.
New to reloading so I'm here to learn . Me and my friend have most of the components. Not sure what CCI primers he has but they are for Bolt and Precision Rifle.
I have RPR in 6.5cm with Chad Dixon 26" barrel
We have 200 of 140 ELD - M bullets. Powder is H4350.
I also have once fired Hornady brass in 6.5 cm.
So my questions are....
What is the load to start with?
How much do you increase the load to test next batch to find that magic/consistent load?
What are the other powder choices besides H4350 that is so hard to find ?
What primers are the best or consistent?
Anybody that has RPR with 26" barrel willing to share their 6.5cm load?
Dimensions for bullet seating.
I'm learning any and all help is truly welcome.
Thanks.
Rate now:
lashlaroe
X52 MONTHS
Premium Member
First Sergeant
Rating: 3.5/5 this site
3295 posts this site
Re: 6.5 Creedmoor
05/16/2016 Last edited 05/16/2016 by lashlaroe
(1 vote)
First things first. Have you reloaded before? No, then please do yourself a favor and read all of the sticky posts in the Reloading forum. Then read the two threads on load development by GhengisAhn.
Then read pages 5-7 of this thread, every post. Bam! You have all the info to answer your questions.
I would start with 40g H4350 and step up 0.6 at a time to 43g and see what you get.
The previous posts all provide good info on IMR4350, H4451, and RL17 as viable replacements.
There was a thread on here a month or so ago that included a great discussion and actual testing done on the primer question. I believe that the take-away from that is that the Federal GMM were most consistent batch to batch, but there were others that worked nearly as well.
Bullet seating depth is a whole subject of its own, but it starts with you knowing where the lands are in your barrel.
Good luck and safe shooting.
Rate now:
straightandtrueX27 MONTHS
Premium Member
Corporal
Rating: 3.3/5 this site
93 posts this site
Re: 6.5 Creedmoor
05/16/2016
(1 vote)
No, but my friend has . He has the whole set up since he reloads for himself.
I will check other treads on here.
Thank you Lash
.
Rate now:
lashlaroe
X52 MONTHS
Premium Member
First Sergeant
Rating: 3.5/5 this site
3295 posts this site
Re: 6.5 Creedmoor
05/16/2016
(1 vote)
Knowledge is power. Or...knowledge of powder is power.
Rate now:
mark5pt56
XFirst Sergeant
Rating: 3.0/5 this site
2406 posts this site
Re: 6.5 Creedmoor
05/22/2016 Last edited 05/22/2016 by mark5pt56
IMR4451/Berger 140 Hybrid
Fed GM210M
2x Hornady brass full length sized on standard RCBS dies and seated on same
Also, H4895 test with regular and reduced load data(only do this with H4895 if listed)
The 37.7 is over .1, no pressure.
24" AIAT
[/IMG]
[/IMG]
[/IMG]
Rate now:
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
05/23/2016
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
05/25/2016
(1 vote)
43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
05/29/2016
While totally awesome, realize that that SD is luck. Litz measured the Magnetospeed to have a SD in its MEASUREMENT of about 5 fps, meaning even a perfect load would average 5 fps over a significant number of rounds. Anything below 5 is luck.
That being said, can you teach me to reload? Can I have your voodoo powder? Which chants do you utter as you pour your powder? Do you account for variations in the Earth's gravitational field?
Well done.
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
05/30/2016
The only thing I can attribute this level of consistency to is the factory brass. The only thing I do is run it through the Giraud to chamfer and debur and get the OAL a little more consistent. Seems like the fresh stuff shoots better for me. Getting neck tension and runout perfect on the next firing is hard for me. I still use a Redding beam scale and trickle up every charge, but I do have a Prometheus on order. Can't wait for that!
Rating: 0.0/5 this site
11 posts this site
Re: 6.5 Creedmoor
05/03/2016
Tag
Rate now:
ArmyJerryXFirst Sergeant
Rating: 3.3/5 this site
3725 posts this site
Re: 6.5 Creedmoor
05/07/2016
Rob any report back on the new powder?
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
05/10/2016
(1 vote)
140 ELD M @ 2.217 to ogive
Virgin Hornady brass
42.6 H4350
FGM210m
4 shots at 200 yards
[IMG2=JSON]{"alt":" photo 58994AA1-E325-4D35-B0B8-0E90C4F2DDE7_zpsihkfwk3s.png","data-align":"none","data-size":"full","src":"http:\/\/i802.photobucket.com\/albums\/yy305\/stewartellis3007\/58994AA1-E325-4D35-B0B8-0E90C4F2DDE7_zpsihkfwk3s.png"}[/IMG2]
Rate now:
jomo34XPrivate
Rating: 0.0/5 this site
3 posts this site
Re: 6.5 Creedmoor
05/11/2016
Tag
Rate now:
BLS27XSergeant
Rating: 3.1/5 this site
186 posts this site
Re: 6.5 Creedmoor
05/13/2016
Ruger Precision Rifle
140g Hornady HPBT
40.6 (2700fps 2.8 SD ) & 41.8 (2798fps 6.6 SD) - Reloader 17
Winchester Brass (annealed, FL resized)
CCI 200 Primers
Both loads cut a nice 3/8 hole @ 100 yards
Rate now:
straightandtrueX27 MONTHS
Premium Member
Corporal
Rating: 3.3/5 this site
93 posts this site
Re: 6.5 Creedmoor
05/16/2016 Last edited 05/16/2016 by straightandtrue
(1 vote)
Ok Ladies and Gentleman.
New to reloading so I'm here to learn . Me and my friend have most of the components. Not sure what CCI primers he has but they are for Bolt and Precision Rifle.
I have RPR in 6.5cm with Chad Dixon 26" barrel
We have 200 of 140 ELD - M bullets. Powder is H4350.
I also have once fired Hornady brass in 6.5 cm.
So my questions are....
What is the load to start with?
How much do you increase the load to test next batch to find that magic/consistent load?
What are the other powder choices besides H4350 that is so hard to find ?
What primers are the best or consistent?
Anybody that has RPR with 26" barrel willing to share their 6.5cm load?
Dimensions for bullet seating.
I'm learning any and all help is truly welcome.
Thanks.
Rate now:
lashlaroe
X52 MONTHS
Premium Member
First Sergeant
Rating: 3.5/5 this site
3295 posts this site
Re: 6.5 Creedmoor
05/16/2016 Last edited 05/16/2016 by lashlaroe
(1 vote)
First things first. Have you reloaded before? No, then please do yourself a favor and read all of the sticky posts in the Reloading forum. Then read the two threads on load development by GhengisAhn.
Then read pages 5-7 of this thread, every post. Bam! You have all the info to answer your questions.
I would start with 40g H4350 and step up 0.6 at a time to 43g and see what you get.
The previous posts all provide good info on IMR4350, H4451, and RL17 as viable replacements.
There was a thread on here a month or so ago that included a great discussion and actual testing done on the primer question. I believe that the take-away from that is that the Federal GMM were most consistent batch to batch, but there were others that worked nearly as well.
Bullet seating depth is a whole subject of its own, but it starts with you knowing where the lands are in your barrel.
Good luck and safe shooting.
Rate now:
straightandtrueX27 MONTHS
Premium Member
Corporal
Rating: 3.3/5 this site
93 posts this site
Re: 6.5 Creedmoor
05/16/2016
(1 vote)
No, but my friend has . He has the whole set up since he reloads for himself.
I will check other treads on here.
Thank you Lash
.Rate now:
lashlaroe
X52 MONTHS
Premium Member
First Sergeant
Rating: 3.5/5 this site
3295 posts this site
Re: 6.5 Creedmoor
05/16/2016
(1 vote)
Knowledge is power. Or...knowledge of powder is power.
Rate now:
mark5pt56
XFirst Sergeant
Rating: 3.0/5 this site
2406 posts this site
Re: 6.5 Creedmoor
05/22/2016 Last edited 05/22/2016 by mark5pt56
IMR4451/Berger 140 Hybrid
Fed GM210M
2x Hornady brass full length sized on standard RCBS dies and seated on same
Also, H4895 test with regular and reduced load data(only do this with H4895 if listed)
The 37.7 is over .1, no pressure.
24" AIAT
Rate now:
craigosXGunny Sergeant
Rating: 3.2/5 this site
979 posts this site
Re: 6.5 Creedmoor
05/23/2016
jeff1383 wrote:
Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
Same except 43.5 (measured on a sartorius), ES 7 fps ... had 1 shot hits out to 1420 the other day and the Kestrel (custom curve) was spot on. Vel avg 2875 fps out a 24 bartlein with a ultra 7 6.5 on it.Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
05/25/2016
(1 vote)
43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
Rate now:
Flyboy22xXSergeant
Rating: 2.9/5 this site
226 posts this site
Re: 6.5 Creedmoor
05/29/2016
cavjock97 wrote:
43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
While totally awesome, realize that that SD is luck. Litz measured the Magnetospeed to have a SD in its MEASUREMENT of about 5 fps, meaning even a perfect load would average 5 fps over a significant number of rounds. Anything below 5 is luck.
That being said, can you teach me to reload? Can I have your voodoo powder? Which chants do you utter as you pour your powder? Do you account for variations in the Earth's gravitational field?
Well done.
Rate now:
cavjock97X77 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
450 posts this site
Re: 6.5 Creedmoor
05/30/2016
Flyboy22x wrote:
That being said, can you teach me to reload? Can I have your voodoo powder? Which chants do you utter as you pour your powder? Do you account for variations in the Earth's gravitational field?
Well done.
I hear ya. I'm happy with a load if the SD is anywhere below 10. SDs like this are certainly not an every day occurrence for me.cavjock97 wrote:
43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
While totally awesome, realize that that SD is luck. Litz measured the Magnetospeed to have a SD in its MEASUREMENT of about 5 fps, meaning even a perfect load would average 5 fps over a significant number of rounds. Anything below 5 is luck. 43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
That being said, can you teach me to reload? Can I have your voodoo powder? Which chants do you utter as you pour your powder? Do you account for variations in the Earth's gravitational field?
Well done.
The only thing I can attribute this level of consistency to is the factory brass. The only thing I do is run it through the Giraud to chamfer and debur and get the OAL a little more consistent. Seems like the fresh stuff shoots better for me. Getting neck tension and runout perfect on the next firing is hard for me. I still use a Redding beam scale and trickle up every charge, but I do have a Prometheus on order. Can't wait for that!
G
Guest
Guest
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
06/01/2016
Rate now:
CMonty256
XSergeant
Rating: 3.0/5 this site
288 posts this site
Re: 6.5 Creedmoor
06/13/2016
(1 vote)
Rifle: GAP Trued 700, 26" Bartein 1:8, TBAC 30CB9
Brass: 1x Fired Hornady
Primer: Federal Gold Medal 210M
Powder: H4350 42.6gr
Bullet: Berger 140 hybrid
MV 2836 SD 6.4
Rate now:
yukikazewayne
XSergeant
Rating: 3.1/5 this site
102 posts this site
Re: 6.5 Creedmoor
06/18/2016 Last edited 06/18/2016 by yukikazewayne
(1 vote)
Since H4350 is really hard to find right now, did anyone ever try N150/N550 instead?
Rate now:
502ChevelleXGunny Sergeant
Rating: 3.3/5 this site
542 posts this site
Re: 6.5 Creedmoor
06/19/2016
Haven't tried the vihta, but the h4350 is so hard to find, I'm going to 4451. Tried a 1 pounder, and had good results, so 8 lbs are on the way. Figure I'll start load development all over, but it's all good.
Rate now:
georgiat01336XPrivate
Rating: 0.0/5 this site
33 posts this site
Re: 6.5 Creedmoor
06/21/2016
what loads are you all using who have switched to the IMR 4451? I have some coming and was curious what everyone is using.
Rate now:
Mopar67XPrivate
Rating: 0.0/5 this site
26 posts this site
Re: 6.5 Creedmoor
06/28/2016
Tag
Rate now:
billyburl2XGunny Sergeant
Rating: 3.1/5 this site
965 posts this site
Re: 6.5 Creedmoor
06/28/2016
I have been having difficulties getting the new 140 ELD-M to perform in my 8.5 twist barrel, has anybody else notice this?
Rate now:
flyer037
XGunny Sergeant
Rating: 3.0/5 this site
563 posts this site
Re: 6.5 Creedmoor
07/11/2016
Tag for future reference
Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2054 posts this site
Re: 6.5 Creedmoor
07/17/2016
Anyone try AA4350 powder? It's readily available here, and fairly cheap.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/18/2016
I've got a bunch of data compiled for my 6.5 Creed. Hope this helps everyone.
GA PRECISION CRUSADER 6.5 CREEDMOR
26" MTU 1:8 Krieger
Load data
42.4 H4350, 140 Berger vld, FGM210 @ 2.165 to ogive. 2794 fps
140 ELD m at 2.217 to ogive. 42.6 h4350.
4 shots was .10 moa. 2800 fps at 74 degree
****43.1 h4350 ### COLD WEATHER###
140 hybrid
2.166 to ogive
57 Fahrenheit = 2813 average
31 Fahrenheit = 2798 fps.
PET LOADS
140 vld. 42.4 H4350, 2.140 to ogive. Fgm210m
140 hybrid at 2.125 to ogive 42.6 H4350, 42.5 r17
130 vld at 2.140 to ogive. 44.0 h4350 2930 fps.
139 scenar at 2.229 to ogive. 40.8 r17. 2780 fps at 10 ft. .22 MOA 7 shots.
140 amax. 42.7 r17. 2.800"
2910 fps.
140 hybrid 42.7 r17. at 2.125. 2920 fps.
****COLD WEATHER****
140 hybrid 43.1 H4350. at 2.155 to ogive. 2800 fps. ******** 30 degrees F and below
New BBL 4/24/15
140 vld. 2.136 to ogive. 42.4 H4350 , fgm210 m. 2790 fps.
Chronographed
140 vld
42.6 H4350
at 2.200"
1)2785
2)2794
3)2791
ES 9
Sd 4
Average 2790 fps
140 hybrid. 42.5 r17. 2.142 to ogive.
2896 fps
130 vld. 43.2 r17. 2.137 to ogive
2990 fps
76 degrees. 29.93 in/hg
140 Hybrid
42.6 H4350
@ 2.173 to ogive.
2805 fps
1/2 moa
140 hybrid @ 2.187 to ogive. 42.6 h4350
.3 moa or less. fire formed brass. .289 bushing
140 vld
42.6 H4350
890 yards.
23.5 moa
85 degrees 40.6 humidity
30.18 in hg
42.6 h4350
140 hunting VLD @ 2.145 to ogive.
26.6 moa at 974 yards.
42.6 H4350. 140 hybrid at 2.189 to ogive. .27 moa
42.2 h4350
139 scenar
2.220
2818 fps. Shot good.
42.5 h
140 vld @ 2.195
2805
.289 moa
5 shots witn sd of 6 ES of 18
140 hybrid. 2.187 to ogive. 42.6 h4350
.3 moa or less. 10-13-15 fire formed brass. .289 bushing
890 yards. 140 vld
23.5 moa
85 degrees 40.6 humidity
30.18 in hg
42.6 h4350
140 hunting VLD
26.6 moa @ 974 yards
GAP
August 2015
42.6 H4350
140 hybrid @ 2.173
2805 fps
1/2 moa
42.2 h4350
139 scenar
2.220
2818 fps. Shot good.
42.5 h4350
140 vld @ 2.195
2805
.289 moa
5 shots witn sd of 6 ES of 18
123 AMAX
41.8 varget. 2.201 to ogive.
3040 fps.
1/2 moa
42.5 r17 with a 140 amax. 2.800. 2910 fps and a tack driver
42.6 H4350. 140 hybrid at 2.189 to ogive. .27 moa
42.6 H4350. 140 eld m @ 2.227 to ogive. 2800 fps.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/18/2016
(1 vote)
Just shot this trying out some new dies.
42.6 H4350
140 amax @ 2.189 to ogive. (2.813" coal)
Once fired brass bumped 2 1/2/1000's" with a .289 bushing in a Redding FL Type S. Trimmed with RCBS Trim Pro power trimmer to 1.610" with 3 way cutter carbide head.
(I actually pulled the shot high right)
4 shots at 102 yards
[IMG2=JSON]{"alt":" photo 832F864E-EE99-478F-BF0D-E9A821D4E5B4_zps7ii4te9z.png","data-align":"none","data-size":"full","src":"http:\/\/i802.photobucket.com\/albums\/yy305\/stewartellis3007\/Mobile%20Uploads\/2016-07\/832F864E-EE99-478F-BF0D-E9A821D4E5B4_zps7ii4te9z.png"}[/IMG2]
Rate now:
RPR65CreedXPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
07/18/2016
I use Redding competition, it seems to work very well. I have a two die set for my 6.5 and have able to make very precise changes in loades by changing out the different neck sizing collets. A bit pricey but I'd say they're worthy it.
Rate now:
prestinbXPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
07/24/2016
Tag
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/29/2016
---------------------------------------------
--- Flyboy22x wrote:
Thus far on my AXMC with 26" Bartlein barrel, I've gotten these ladder test results using H4350, BR2 Primers, Prime (Norma) brass, and Berger 130 AR Hybrids @ 300 yards:
I really haven't seen much in the way of pressure, even at 44.2 grains. I loaded up another ladder from 44.0 to 44.9 in .1 increments but haven't shot it yet... is that too hot?? My ladder test indicates maybe there is another node in the low 44's... it would be nice to have more data.
I only chrono'd 43.4gr at 2830 fps, which seems slow for a 26" barrel compared to many others on here. Is this possibly due to barrel break-in? My target velocity for 130 Hybrids is about 2900 fps, though now I'm nervous to push past 44 grains since nobody else seems to be going that high.
Flyboy, fwiw, I'm shooting the 130 OTM Berger with 43.8 H4350, Hornady brass, Fgm210m, with bullet at 2.188" to ogive ( 2.810" COAL roughly). I shot a 5 shot string the other day with average MV at 2938 fps. This was confirmed at 495 yards ( 8.3 moa) and 700 yards (14.7 moa.... With 100 yard zero). Both groups were sub moa.
This is out of a GAP Crusader with a 26" 1:8 Krieger MTU. I also shot a 5 shot group at 100 yards while getting the charge "perfected" and it was .18 moa group. Really like these 130's.
---------------------------------------------
Rate now:
jaybigboy34XPrivate
Rating: 3.0/5 this site
13 posts this site
Re: 6.5 Creedmoor
07/29/2016
Anybody shoot with your bullet touching the lands? How do they perform if so?
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
08/10/2016 Last edited 08/10/2016 by CaneZach
Here's my 123 AMAX load with RL17:
Once fired Prime brass, FL sized and trimmed to 1.910"
42.4 grains Relder 17
CCI BR2 primers
2.210" to ogive
AVG velocity 3052 fps with SD of 9 out of a 26" DTA barrel with Silencer Tech suppressor
Rate now:
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
06/01/2016
cavjock97 wrote:
43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
hmm...i like the looks of all this... 43.2 H4350
130 Hybrid -Pointed- BC .600
2.845 OAL
22.75" Bartlein with Crux Ark338 Can
Dead Nutz to 1,200 yards
CJ97
Rate now:
CMonty256
XSergeant
Rating: 3.0/5 this site
288 posts this site
Re: 6.5 Creedmoor
06/13/2016
(1 vote)
Rifle: GAP Trued 700, 26" Bartein 1:8, TBAC 30CB9
Brass: 1x Fired Hornady
Primer: Federal Gold Medal 210M
Powder: H4350 42.6gr
Bullet: Berger 140 hybrid
MV 2836 SD 6.4
Rate now:
yukikazewayne
XSergeant
Rating: 3.1/5 this site
102 posts this site
Re: 6.5 Creedmoor
06/18/2016 Last edited 06/18/2016 by yukikazewayne
(1 vote)
Since H4350 is really hard to find right now, did anyone ever try N150/N550 instead?
Rate now:
502ChevelleXGunny Sergeant
Rating: 3.3/5 this site
542 posts this site
Re: 6.5 Creedmoor
06/19/2016
Haven't tried the vihta, but the h4350 is so hard to find, I'm going to 4451. Tried a 1 pounder, and had good results, so 8 lbs are on the way. Figure I'll start load development all over, but it's all good.
Rate now:
georgiat01336XPrivate
Rating: 0.0/5 this site
33 posts this site
Re: 6.5 Creedmoor
06/21/2016
what loads are you all using who have switched to the IMR 4451? I have some coming and was curious what everyone is using.
Rate now:
Mopar67XPrivate
Rating: 0.0/5 this site
26 posts this site
Re: 6.5 Creedmoor
06/28/2016
Tag
Rate now:
billyburl2XGunny Sergeant
Rating: 3.1/5 this site
965 posts this site
Re: 6.5 Creedmoor
06/28/2016
I have been having difficulties getting the new 140 ELD-M to perform in my 8.5 twist barrel, has anybody else notice this?
Rate now:
flyer037
XGunny Sergeant
Rating: 3.0/5 this site
563 posts this site
Re: 6.5 Creedmoor
07/11/2016
Tag for future reference
Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2054 posts this site
Re: 6.5 Creedmoor
07/17/2016
Anyone try AA4350 powder? It's readily available here, and fairly cheap.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/18/2016
I've got a bunch of data compiled for my 6.5 Creed. Hope this helps everyone.
GA PRECISION CRUSADER 6.5 CREEDMOR
26" MTU 1:8 Krieger
Load data
42.4 H4350, 140 Berger vld, FGM210 @ 2.165 to ogive. 2794 fps
140 ELD m at 2.217 to ogive. 42.6 h4350.
4 shots was .10 moa. 2800 fps at 74 degree
****43.1 h4350 ### COLD WEATHER###
140 hybrid
2.166 to ogive
57 Fahrenheit = 2813 average
31 Fahrenheit = 2798 fps.
PET LOADS
140 vld. 42.4 H4350, 2.140 to ogive. Fgm210m
140 hybrid at 2.125 to ogive 42.6 H4350, 42.5 r17
130 vld at 2.140 to ogive. 44.0 h4350 2930 fps.
139 scenar at 2.229 to ogive. 40.8 r17. 2780 fps at 10 ft. .22 MOA 7 shots.
140 amax. 42.7 r17. 2.800"
2910 fps.
140 hybrid 42.7 r17. at 2.125. 2920 fps.
****COLD WEATHER****
140 hybrid 43.1 H4350. at 2.155 to ogive. 2800 fps. ******** 30 degrees F and below
New BBL 4/24/15
140 vld. 2.136 to ogive. 42.4 H4350 , fgm210 m. 2790 fps.
Chronographed
140 vld
42.6 H4350
at 2.200"
1)2785
2)2794
3)2791
ES 9
Sd 4
Average 2790 fps
140 hybrid. 42.5 r17. 2.142 to ogive.
2896 fps
130 vld. 43.2 r17. 2.137 to ogive
2990 fps
76 degrees. 29.93 in/hg
140 Hybrid
42.6 H4350
@ 2.173 to ogive.
2805 fps
1/2 moa
140 hybrid @ 2.187 to ogive. 42.6 h4350
.3 moa or less. fire formed brass. .289 bushing
140 vld
42.6 H4350
890 yards.
23.5 moa
85 degrees 40.6 humidity
30.18 in hg
42.6 h4350
140 hunting VLD @ 2.145 to ogive.
26.6 moa at 974 yards.
42.6 H4350. 140 hybrid at 2.189 to ogive. .27 moa
42.2 h4350
139 scenar
2.220
2818 fps. Shot good.
42.5 h
140 vld @ 2.195
2805
.289 moa
5 shots witn sd of 6 ES of 18
140 hybrid. 2.187 to ogive. 42.6 h4350
.3 moa or less. 10-13-15 fire formed brass. .289 bushing
890 yards. 140 vld
23.5 moa
85 degrees 40.6 humidity
30.18 in hg
42.6 h4350
140 hunting VLD
26.6 moa @ 974 yards
GAP
August 2015
42.6 H4350
140 hybrid @ 2.173
2805 fps
1/2 moa
42.2 h4350
139 scenar
2.220
2818 fps. Shot good.
42.5 h4350
140 vld @ 2.195
2805
.289 moa
5 shots witn sd of 6 ES of 18
123 AMAX
41.8 varget. 2.201 to ogive.
3040 fps.
1/2 moa
42.5 r17 with a 140 amax. 2.800. 2910 fps and a tack driver
42.6 H4350. 140 hybrid at 2.189 to ogive. .27 moa
42.6 H4350. 140 eld m @ 2.227 to ogive. 2800 fps.
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/18/2016
(1 vote)
Just shot this trying out some new dies.
42.6 H4350
140 amax @ 2.189 to ogive. (2.813" coal)
Once fired brass bumped 2 1/2/1000's" with a .289 bushing in a Redding FL Type S. Trimmed with RCBS Trim Pro power trimmer to 1.610" with 3 way cutter carbide head.
(I actually pulled the shot high right)
4 shots at 102 yards
[IMG2=JSON]{"alt":" photo 832F864E-EE99-478F-BF0D-E9A821D4E5B4_zps7ii4te9z.png","data-align":"none","data-size":"full","src":"http:\/\/i802.photobucket.com\/albums\/yy305\/stewartellis3007\/Mobile%20Uploads\/2016-07\/832F864E-EE99-478F-BF0D-E9A821D4E5B4_zps7ii4te9z.png"}[/IMG2]
Rate now:
RPR65CreedXPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
07/18/2016
I use Redding competition, it seems to work very well. I have a two die set for my 6.5 and have able to make very precise changes in loades by changing out the different neck sizing collets. A bit pricey but I'd say they're worthy it.
Rate now:
prestinbXPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
07/24/2016
Tag
Rate now:
Aimsmall55XFirst Sergeant
Rating: 3.4/5 this site
3311 posts this site
Re: 6.5 Creedmoor
07/29/2016
---------------------------------------------
--- Flyboy22x wrote:
Thus far on my AXMC with 26" Bartlein barrel, I've gotten these ladder test results using H4350, BR2 Primers, Prime (Norma) brass, and Berger 130 AR Hybrids @ 300 yards:
I really haven't seen much in the way of pressure, even at 44.2 grains. I loaded up another ladder from 44.0 to 44.9 in .1 increments but haven't shot it yet... is that too hot?? My ladder test indicates maybe there is another node in the low 44's... it would be nice to have more data.
I only chrono'd 43.4gr at 2830 fps, which seems slow for a 26" barrel compared to many others on here. Is this possibly due to barrel break-in? My target velocity for 130 Hybrids is about 2900 fps, though now I'm nervous to push past 44 grains since nobody else seems to be going that high.
Flyboy, fwiw, I'm shooting the 130 OTM Berger with 43.8 H4350, Hornady brass, Fgm210m, with bullet at 2.188" to ogive ( 2.810" COAL roughly). I shot a 5 shot string the other day with average MV at 2938 fps. This was confirmed at 495 yards ( 8.3 moa) and 700 yards (14.7 moa.... With 100 yard zero). Both groups were sub moa.
This is out of a GAP Crusader with a 26" 1:8 Krieger MTU. I also shot a 5 shot group at 100 yards while getting the charge "perfected" and it was .18 moa group. Really like these 130's.
---------------------------------------------
Rate now:
jaybigboy34XPrivate
Rating: 3.0/5 this site
13 posts this site
Re: 6.5 Creedmoor
07/29/2016
Anybody shoot with your bullet touching the lands? How do they perform if so?
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
08/10/2016 Last edited 08/10/2016 by CaneZach
Here's my 123 AMAX load with RL17:
Once fired Prime brass, FL sized and trimmed to 1.910"
42.4 grains Relder 17
CCI BR2 primers
2.210" to ogive
AVG velocity 3052 fps with SD of 9 out of a 26" DTA barrel with Silencer Tech suppressor
Rate now:
G
Guest
Guest
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
08/13/2016
Hornady 140 BTHP
40.4 gr Reloder 17
CCI BR2 primers
2.210" to ogive
AVG velocity 2846 and SD of 6.6 out of a 26" DTA barrel with Silencer Tech suppressor
Rate now:
Shanerbanner10XFirst Sergeant
Rating: 3.3/5 this site
1853 posts this site
Re: 6.5 Creedmoor
08/15/2016
(1 vote)
Berger 130 AR Hybrid
43.3 IMR 4451
S&B Primers
Prime Brass
2.850" (20 thou off)
Avg- 2905, SD- 7.6 23.75" Mullerworks barrel Badger action.
Rate now:
mouse0311
XPrivate
Rating: 3.0/5 this site
26 posts this site
Re: 6.5 Creedmoor
08/17/2016
Tag
Rate now:
iShermanXPrivate
Rating: 2.9/5 this site
25 posts this site
Re: 6.5 Creedmoor
08/25/2016
I live n compete in FL. So I change my charge a lot. I totally switched to IMR 4451 since I got tired of chasing H4350 everywhere. I stay between 42.3 - 42.7 depending on the sunny days. H brass annealed, concentricly chamfered n I use ELD-M. I decided to perfect my shooting and brass instead of using Vergers Hybrids that I used to use.
NOW, why doesn't anyone discuss the real factors that affect this cartridge. Neck tension n neck thickness. Also, setting depth???????????
No point on discussing CBTO and COAL since we all have diff chambers.
Rate now:
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
08/26/2016
because i can use a .289 bushing with hornady brass and seat a hybrid/eld/amax 20 thou off and not have to worry about it
Rate now:
EPD33XSergeant
Rating: 2.9/5 this site
352 posts this site
Re: 6.5 Creedmoor
08/28/2016 Last edited 08/28/2016 by EPD33
[IMG2=JSON]{"alt":" photo 8B121C27-1392-4067-80B0-7BB53E9FE4CF_zpscidtshyj.jpg","data-align":"none","data-size":"full","src":"http:\/\/i647.photobucket.com\/albums\/uu197\/nickw_photo\/Mobile%20Uploads\/8B121C27-1392-4067-80B0-7BB53E9FE4CF_zpscidtshyj.jpg"}[/IMG2]
Rate now:
Servo93
XSergeant
Rating: 3.0/5 this site
167 posts this site
Re: 6.5 Creedmoor
09/03/2016
Just finished up load development tonight:
140 ELD
42.3gr H4350
Federal 210M
Hornady once fired brass with shoulders bumped about 0.003"
COL 2.845 (0.020" jump)
AI AT 24" MHS Win Tactical barrel
2795 FPS with a 4.6 SD. Taken with a cheap Chrony, will verify data with ballistics, but the .88" tall groups at 238 yards looked promising.
Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2054 posts this site
Re: 6.5 Creedmoor
09/05/2016 Last edited 09/05/2016 by JGlasgow
42gr of AA4350
Hornady brass
CCI 200 primer
Hornady 140bthp seated to 2.82 C.O.A.L
No velocity numbers yet, and it showed no signs of excessive pressure. Shot at 100 yards.
[IMG2=JSON]{"alt":" photo IMAG0097_zps3lmq8ole.jpg","data-align":"none","data-size":"full","src":"http:\/\/i184.photobucket.com\/albums\/x191\/jmg8550\/Mobile%20Uploads\/2016-09\/IMAG0097_zps3lmq8ole.jpg"}[/IMG2]
Brand new 23" Criterion Prefit stainless barrel with almost 100 rounds through it. Only cleaning with Hoppe's solvent and patches after 50 rounds. This group was also shot suppressed with no correction made for POI shift.
Rate now:
Joe59XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/05/2016
Tag
Rate now:
gerry939XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/11/2016
I have just bought a Ruger precision rifle here in England , caliber 6.5 creedmoor , problem is ammo is as not readily available and no Zeroing targets to zero rifle from 100 to 1000yds on our 100yd range,have got my mate to reload some using the data you have posted, thanks any suggestions re zeroing.
Rate now:
Rob01
XModerator
Rating: 3.8/5 this site
11458 posts this site
Re: 6.5 Creedmoor
09/11/2016
As for zeroing, zero at 100, get your velocity and run it on a ballistic program. I like JBM Ballistics. It's free online and most important it works. You won't get 1000 yard data from a 100 yard target no matter how it's marked as the marks will have to be set for a velocity and bullet and anything different is going to be off. .
Rate now:
gerry939XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/12/2016
Thanks for that I'm off to the range bought a chronograph, have some hand loads 41.5gr of H4350 140 g head ,AOL 2.800 , cci primers so he's hoping thanks again
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
09/13/2016 Last edited 09/13/2016 by towboater91
New to this forum, but I've read all 8 pages of this thread and lots of good info on here. Anyways,
I have a savage model 12 vlp topped with a sightron siii 8-32x56 scope, with a pre-fit criterion 6.5 Creedmoor heavy stainless 26" barrel from northland shooters supply, measures .815 at the muzzle. I've got about 500 rounds thru the barrel now, mostly reloads. I have been shooting 140gr hornady bthp with 42.4 H4350 and Imr 4350 and cci 200 primers, using rcbs 1010 scales, seating the bullet at 2.810 COAL (2.215 to ogive with hornadys OAL length gauge and bullet comparator) .035 thou off the lands. Some groups are 1/2, 1/4 inch and some have crazy fliers, I'm using hornady brass trimmed to 1.910. But I've never cleaned the brass just deburred and chamfered and primer pockets cleaned. Anything else I could do to get rid of the fliers?? I'm trying to get it a little more consistent from batch to batch. I've tried rl17 and imr4451 but haven't gotten very good groups in the 42-43gr range. Started seeing some pressure signs around 43.3 imr4451. The temp in middle Tennessee is about 85 right now. Any input would be appreciated.
Rate now:
Jimgal62X30 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
99 posts this site
Re: 6.5 Creedmoor
09/13/2016
Three items to consider
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
09/14/2016 Last edited 09/14/2016 by towboater91
Yes I clean the barrel about every 40-50 round, but still with this criterion barrel I don't see much copper fouling at all opposed to the ruger m77 varmint target 6.5 i had, so I may be cleaning it to early, but I do need to start cleaning the brass haha,I've just been having good luck without doing it. And no I have not been neck sizing although I do have a Lee neck sizing die, I just full length size everytime, I used to crimp them as well, but I stopped doing that bc I was not seeing any difference in the groups. I was assuming I needed to play with the seating depth a little more. I could be wrong tho.
Rate now:
Joe59XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/19/2016
Just finished my build and break in. Shot first groups today and started load development. 40.5 grins H4350 ,Hornady 140 HPBT, FGM210M primers in New Hornady brass seated .050 off the lands. Shot 4 different loads in 4 different groups,18 rounds total, and all 18shots would fit in a 1inch square. Got to find a longer range for load development.
Rate now:
headoctorXPrivate
Rating: 0.0/5 this site
3 posts this site
Re: 6.5 Creedmoor
09/20/2016 Last edited 09/20/2016 by headoctor
26 Bartlien
Deviant Defiant action
AICS AT
Timney Calvin 8oz
March Magnum
Smithed by GA Precision
140 Berger hybrid
42 H4350
Hornady brass
BR-2 primer
COAL depends on your unique build but I gap at .020
Rate now:
shughes88XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/22/2016 Last edited 09/23/2016 by shughes88
I've had a hard time finding any H4350 anywhere except online and I'm sorry, I'm just not paying the $25 hazmat fee. Not worth it to me. That being said ive worked up a good load with IMR-4350 which I can find almost anywhere. Here is my load data.
Redding S/type dies
.288 neck bushing
140gr. Berger Hybrid
Hornady brass
42.5gr. IMR-4350
CCI BR2 primers
.002 off lands
2710 FPS
This is shot with my new Savage 10BA Stealth 24" barrel completely stock with a Vortex 6-24x50mm tactical scope. Very nice rig for under $2000. Worked up a good load that shot groups in the .18" range at 100yds. but was too slow at 41gr. and 2550fps. Settled for a test group of .293" and at a better 2710fps which suits me for 1000yds and beyond. Hope this helps for anyone struggling like I was to find H4350 in stock. I'd post pics of my grouping but not sure how to post pics!!
Rate now:
shughes88XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/27/2016
Update to my last post: I picked up some IMR-4451 today to test. It's supposed to be the closest thing to H4350 as far as insensitivity to temperature variances. I'm going to run some tests and would be happy to post results when finished and pics if someone could help me out with how to post pics.
Rate now:
mark5685
XPrivate
Rating: 0.0/5 this site
9 posts this site
Re: 6.5 Creedmoor
09/28/2016 Last edited 09/28/2016 by mark5685
Hornady Brass
Sierra MatchKing 140Gr HPBT
42 gr Hodgdon Hybrid 100V
Federal Large Rifle Primers
Shot this recipe through my Ruger Precision Gen 2 w/ Trijicon Accupoint 5-20x50 glass @ 100 yards
Rate now:
verdugo60XFirst Sergeant
Rating: 3.2/5 this site
1220 posts this site
Re: 6.5 Creedmoor
10/01/2016
Almost my exact load, any chance you could run your ballistic solver with 6500 DA 65 degrees? I'm interested in the MIL come ups @ 640 yds, 840 yds and 1040 yds. Thanks sir, trying to figure out an issue with my ballistic solver.
---------------------------------------------
--- Servo93 wrote:
Just finished up load development tonight:
140 ELD
42.3gr H4350
Federal 210M
Hornady once fired brass with shoulders bumped about 0.003"
COL 2.845 (0.020" jump)
AI AT 24" MHS Win Tactical barrel
2795 FPS with a 4.6 SD. Taken with a cheap Chrony, will verify data with ballistics, but the .88" tall groups at 238 yards looked promising.
---------------------------------------------
Rate now:
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
10/03/2016
6500 DA, 65 degrees, 2.45" scope height, no winds
Ballistic AE
640: 3.68
840: 5.67
1040: 8.01
TRASOL
640: 3.7
840: 5.8
1040: 8.1
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
08/13/2016
Hornady 140 BTHP
40.4 gr Reloder 17
CCI BR2 primers
2.210" to ogive
AVG velocity 2846 and SD of 6.6 out of a 26" DTA barrel with Silencer Tech suppressor
Rate now:
Shanerbanner10XFirst Sergeant
Rating: 3.3/5 this site
1853 posts this site
Re: 6.5 Creedmoor
08/15/2016
(1 vote)
Berger 130 AR Hybrid
43.3 IMR 4451
S&B Primers
Prime Brass
2.850" (20 thou off)
Avg- 2905, SD- 7.6 23.75" Mullerworks barrel Badger action.
Rate now:
mouse0311
XPrivate
Rating: 3.0/5 this site
26 posts this site
Re: 6.5 Creedmoor
08/17/2016
Tag
Rate now:
iShermanXPrivate
Rating: 2.9/5 this site
25 posts this site
Re: 6.5 Creedmoor
08/25/2016
I live n compete in FL. So I change my charge a lot. I totally switched to IMR 4451 since I got tired of chasing H4350 everywhere. I stay between 42.3 - 42.7 depending on the sunny days. H brass annealed, concentricly chamfered n I use ELD-M. I decided to perfect my shooting and brass instead of using Vergers Hybrids that I used to use.
NOW, why doesn't anyone discuss the real factors that affect this cartridge. Neck tension n neck thickness. Also, setting depth???????????
No point on discussing CBTO and COAL since we all have diff chambers.
Rate now:
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
08/26/2016
because i can use a .289 bushing with hornady brass and seat a hybrid/eld/amax 20 thou off and not have to worry about it
Rate now:
EPD33XSergeant
Rating: 2.9/5 this site
352 posts this site
Re: 6.5 Creedmoor
08/28/2016 Last edited 08/28/2016 by EPD33
craigos wrote:
43.3 was magic number for me too. I run CCI primers. .010 off the lands. Although my muzzle velocity was only 2802fps avg with 24" Bartlein bbl w/ Badger Mini-FTE brake. This group measures .625 and was shot at 310 yards. The 130 Hybrids shoot much better than the 140gr ELD-M for me.jeff1383 wrote:
Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
Same except 43.5 (measured on a sartorius), ES 7 fps ... had 1 shot hits out to 1420 the other day and the Kestrel (custom curve) was spot on. Vel avg 2875 fps out a 24 bartlein with a ultra 7 6.5 on it.Hornady brass
Fed210match primer
130 berger hybrid
43.3 h4350
Seated .010 off
MV avg 2922
Shot out to 1200 yards nicely on a calm day.
[IMG2=JSON]{"alt":" photo 8B121C27-1392-4067-80B0-7BB53E9FE4CF_zpscidtshyj.jpg","data-align":"none","data-size":"full","src":"http:\/\/i647.photobucket.com\/albums\/uu197\/nickw_photo\/Mobile%20Uploads\/8B121C27-1392-4067-80B0-7BB53E9FE4CF_zpscidtshyj.jpg"}[/IMG2]
Rate now:
Servo93
XSergeant
Rating: 3.0/5 this site
167 posts this site
Re: 6.5 Creedmoor
09/03/2016
Just finished up load development tonight:
140 ELD
42.3gr H4350
Federal 210M
Hornady once fired brass with shoulders bumped about 0.003"
COL 2.845 (0.020" jump)
AI AT 24" MHS Win Tactical barrel
2795 FPS with a 4.6 SD. Taken with a cheap Chrony, will verify data with ballistics, but the .88" tall groups at 238 yards looked promising.
Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2054 posts this site
Re: 6.5 Creedmoor
09/05/2016 Last edited 09/05/2016 by JGlasgow
42gr of AA4350
Hornady brass
CCI 200 primer
Hornady 140bthp seated to 2.82 C.O.A.L
No velocity numbers yet, and it showed no signs of excessive pressure. Shot at 100 yards.
[IMG2=JSON]{"alt":" photo IMAG0097_zps3lmq8ole.jpg","data-align":"none","data-size":"full","src":"http:\/\/i184.photobucket.com\/albums\/x191\/jmg8550\/Mobile%20Uploads\/2016-09\/IMAG0097_zps3lmq8ole.jpg"}[/IMG2]
Brand new 23" Criterion Prefit stainless barrel with almost 100 rounds through it. Only cleaning with Hoppe's solvent and patches after 50 rounds. This group was also shot suppressed with no correction made for POI shift.
Rate now:
Joe59XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/05/2016
Tag
Rate now:
gerry939XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/11/2016
I have just bought a Ruger precision rifle here in England , caliber 6.5 creedmoor , problem is ammo is as not readily available and no Zeroing targets to zero rifle from 100 to 1000yds on our 100yd range,have got my mate to reload some using the data you have posted, thanks any suggestions re zeroing.
Rate now:
Rob01
XModerator
Rating: 3.8/5 this site
11458 posts this site
Re: 6.5 Creedmoor
09/11/2016
gerry939 wrote:
I have just bought a Ruger precision rifle here in England , caliber 6.5 creedmoor , problem is ammo is as not readily available and no Zeroing targets to zero rifle from 100 to 1000yds on our 100yd range,have got my mate to reload some using the data you have posted, thanks any suggestions re zeroing.
Good rifle and too bad you are having an ammo issue. Can your local dealer order it?I have just bought a Ruger precision rifle here in England , caliber 6.5 creedmoor , problem is ammo is as not readily available and no Zeroing targets to zero rifle from 100 to 1000yds on our 100yd range,have got my mate to reload some using the data you have posted, thanks any suggestions re zeroing.
As for zeroing, zero at 100, get your velocity and run it on a ballistic program. I like JBM Ballistics. It's free online and most important it works. You won't get 1000 yard data from a 100 yard target no matter how it's marked as the marks will have to be set for a velocity and bullet and anything different is going to be off. .
Rate now:
gerry939XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/12/2016
Thanks for that I'm off to the range bought a chronograph, have some hand loads 41.5gr of H4350 140 g head ,AOL 2.800 , cci primers so he's hoping thanks again
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
09/13/2016 Last edited 09/13/2016 by towboater91
New to this forum, but I've read all 8 pages of this thread and lots of good info on here. Anyways,
I have a savage model 12 vlp topped with a sightron siii 8-32x56 scope, with a pre-fit criterion 6.5 Creedmoor heavy stainless 26" barrel from northland shooters supply, measures .815 at the muzzle. I've got about 500 rounds thru the barrel now, mostly reloads. I have been shooting 140gr hornady bthp with 42.4 H4350 and Imr 4350 and cci 200 primers, using rcbs 1010 scales, seating the bullet at 2.810 COAL (2.215 to ogive with hornadys OAL length gauge and bullet comparator) .035 thou off the lands. Some groups are 1/2, 1/4 inch and some have crazy fliers, I'm using hornady brass trimmed to 1.910. But I've never cleaned the brass just deburred and chamfered and primer pockets cleaned. Anything else I could do to get rid of the fliers?? I'm trying to get it a little more consistent from batch to batch. I've tried rl17 and imr4451 but haven't gotten very good groups in the 42-43gr range. Started seeing some pressure signs around 43.3 imr4451. The temp in middle Tennessee is about 85 right now. Any input would be appreciated.
Rate now:
Jimgal62X30 MONTHS
Premium Member
Sergeant
Rating: 3.0/5 this site
99 posts this site
Re: 6.5 Creedmoor
09/13/2016
Three items to consider
- Have you checked for copper fouling in the barrel?
- Are you neck sizing? I use a .289 bushing.
- Cleaning your brass should be in your routine for brass prep. I use an ultrasonic cleaner and trim for growth after each load cycle.
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
09/14/2016 Last edited 09/14/2016 by towboater91
Yes I clean the barrel about every 40-50 round, but still with this criterion barrel I don't see much copper fouling at all opposed to the ruger m77 varmint target 6.5 i had, so I may be cleaning it to early, but I do need to start cleaning the brass haha,I've just been having good luck without doing it. And no I have not been neck sizing although I do have a Lee neck sizing die, I just full length size everytime, I used to crimp them as well, but I stopped doing that bc I was not seeing any difference in the groups. I was assuming I needed to play with the seating depth a little more. I could be wrong tho.
Rate now:
Joe59XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/19/2016
Just finished my build and break in. Shot first groups today and started load development. 40.5 grins H4350 ,Hornady 140 HPBT, FGM210M primers in New Hornady brass seated .050 off the lands. Shot 4 different loads in 4 different groups,18 rounds total, and all 18shots would fit in a 1inch square. Got to find a longer range for load development.
Rate now:
headoctorXPrivate
Rating: 0.0/5 this site
3 posts this site
Re: 6.5 Creedmoor
09/20/2016 Last edited 09/20/2016 by headoctor
26 Bartlien
Deviant Defiant action
AICS AT
Timney Calvin 8oz
March Magnum
Smithed by GA Precision
140 Berger hybrid
42 H4350
Hornady brass
BR-2 primer
COAL depends on your unique build but I gap at .020
Rate now:
shughes88XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/22/2016 Last edited 09/23/2016 by shughes88
I've had a hard time finding any H4350 anywhere except online and I'm sorry, I'm just not paying the $25 hazmat fee. Not worth it to me. That being said ive worked up a good load with IMR-4350 which I can find almost anywhere. Here is my load data.
Redding S/type dies
.288 neck bushing
140gr. Berger Hybrid
Hornady brass
42.5gr. IMR-4350
CCI BR2 primers
.002 off lands
2710 FPS
This is shot with my new Savage 10BA Stealth 24" barrel completely stock with a Vortex 6-24x50mm tactical scope. Very nice rig for under $2000. Worked up a good load that shot groups in the .18" range at 100yds. but was too slow at 41gr. and 2550fps. Settled for a test group of .293" and at a better 2710fps which suits me for 1000yds and beyond. Hope this helps for anyone struggling like I was to find H4350 in stock. I'd post pics of my grouping but not sure how to post pics!!
Rate now:
shughes88XPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
09/27/2016
Update to my last post: I picked up some IMR-4451 today to test. It's supposed to be the closest thing to H4350 as far as insensitivity to temperature variances. I'm going to run some tests and would be happy to post results when finished and pics if someone could help me out with how to post pics.
Rate now:
mark5685
XPrivate
Rating: 0.0/5 this site
9 posts this site
Re: 6.5 Creedmoor
09/28/2016 Last edited 09/28/2016 by mark5685
Hornady Brass
Sierra MatchKing 140Gr HPBT
42 gr Hodgdon Hybrid 100V
Federal Large Rifle Primers
Shot this recipe through my Ruger Precision Gen 2 w/ Trijicon Accupoint 5-20x50 glass @ 100 yards
Rate now:
verdugo60XFirst Sergeant
Rating: 3.2/5 this site
1220 posts this site
Re: 6.5 Creedmoor
10/01/2016
Almost my exact load, any chance you could run your ballistic solver with 6500 DA 65 degrees? I'm interested in the MIL come ups @ 640 yds, 840 yds and 1040 yds. Thanks sir, trying to figure out an issue with my ballistic solver.
---------------------------------------------
--- Servo93 wrote:
Just finished up load development tonight:
140 ELD
42.3gr H4350
Federal 210M
Hornady once fired brass with shoulders bumped about 0.003"
COL 2.845 (0.020" jump)
AI AT 24" MHS Win Tactical barrel
2795 FPS with a 4.6 SD. Taken with a cheap Chrony, will verify data with ballistics, but the .88" tall groups at 238 yards looked promising.
---------------------------------------------
Rate now:
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
10/03/2016
verdugo60 wrote:
Almost my exact load, any chance you could run your ballistic solver with 6500 DA 65 degrees? I'm interested in the MIL come ups @ 640 yds, 840 yds and 1040 yds. Thanks sir, trying to figure out an issue with my ballistic solver.
---------------------------------------------
--- Servo93 wrote:
Just finished up load development tonight:
140 ELD
42.3gr H4350
Federal 210M
Hornady once fired brass with shoulders bumped about 0.003"
COL 2.845 (0.020" jump)
AI AT 24" MHS Win Tactical barrel
2795 FPS with a 4.6 SD. Taken with a cheap Chrony, will verify data with ballistics, but the .88" tall groups at 238 yards looked promising.
---------------------------------------------
this is the same speed factory 140 eld runs in my ATAlmost my exact load, any chance you could run your ballistic solver with 6500 DA 65 degrees? I'm interested in the MIL come ups @ 640 yds, 840 yds and 1040 yds. Thanks sir, trying to figure out an issue with my ballistic solver.
---------------------------------------------
--- Servo93 wrote:
Just finished up load development tonight:
140 ELD
42.3gr H4350
Federal 210M
Hornady once fired brass with shoulders bumped about 0.003"
COL 2.845 (0.020" jump)
AI AT 24" MHS Win Tactical barrel
2795 FPS with a 4.6 SD. Taken with a cheap Chrony, will verify data with ballistics, but the .88" tall groups at 238 yards looked promising.
---------------------------------------------
6500 DA, 65 degrees, 2.45" scope height, no winds
Ballistic AE
640: 3.68
840: 5.67
1040: 8.01
TRASOL
640: 3.7
840: 5.8
1040: 8.1
G
Guest
Guest
KibaSHX72 MONTHS
Premium Member
First Sergeant
Rating: 3.4/5 this site
1360 posts this site
Re: 6.5 Creedmoor
10/06/2016 Last edited 10/06/2016 by KibaSH
Anyone playing with RL16 yet? Alliant's test data is showing higher velocities at the same pressure, lower SD, and less temperature sensitivity compared to the old standby of H4350. Density of RL16 is slightly lower than H4350 so it takes a little more RL16 compared to H4350 to match the pressures but the data looks really good.
Early reports on other forums are very promising regarding velocity/SD/accuracy.
Even though I'm sitting on quite a bit of H4350 I have some RL16 on the way and will be testing with it soon. Just wondered if anyone else on here is already experimenting with it...
Rate now:
Ed043XPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
10/08/2016
I'm new to the 6.5 but not new to reloading. What do y'all recommend for 120 gr Speer SP and a Ruger American? I just got it and haven't had a chance to check the OAl or anything. I did however put 60 rounds thru it using the Hornady Match 120 gr A-max and are loving the results. I'm getting 1 1/2" to 2" groups at 300 yards.
I'm looking forward to being on this site and looking around.
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
10/09/2016 Last edited 10/17/2016 by CaneZach
Barnes 140 Match Burner
2.214" to ogive
1x Hornady brass
41.9 grains H4350
FGM210M primers
26" DTA barrel with SilencerTech suppressor
Avg MV 2806, ES 20, SD 8.4
70°, 5660' asl, 24.66 inHg
Today was the first time I tried these bullets. Advertised G1 of 0.586 was REAL close and Ballistic AE G7 drag model gave me a 0.293 G7. Called for 8.14 mils of elevation to get to 1080 yards. I needed 8.2 to get on target, so pretty damn close to advertised. I still want to play around with seating depth to tighten up the groups, but it really looks promising.
Rate now:
DaveThomas83XSergeant
Rating: 3.0/5 this site
278 posts this site
Re: 6.5 Creedmoor
10/10/2016
I've seen some RL17 loads here and there, it seems to be slightly more available in my area so I picked up a pound to work into some load dev. Seems like 40-41gr is the sweet spot for alot of you, hopefully it will be the same for me.
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
10/10/2016 Last edited 10/10/2016 by CaneZach
Edit: For what it's worth, I get better velocities with RL17 while using less powder than H4350. Not an apples to apples comparison, but I use 41.9 grains of H4350 with the Barnes 140 Match Burner and my MV is 2806. With 40.4 grains of RL17 and a Hornady 140 BTHP, I was in the 2850 range
Rate now:
PalmettoPride29412
XGunny Sergeant
Rating: 3.4/5 this site
518 posts this site
Re: 6.5 Creedmoor
11/05/2016
Anybody got a load for Hornady's new .264/6.5mm 147gr ELD Match bullet? I just ordered 200 from Midway.
Rate now:
erslllXSergeant
Rating: 3.0/5 this site
107 posts this site
Re: 6.5 Creedmoor
11/05/2016
I am surprised that Midway has the 147gr already.
Anyone with 143gr ELD-X load info?
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
11/06/2016
I think this might be the first Reloder 16 load in this thread, so hopefully we'll see a few more. I've found, in limited testing, that Reloder 16 is producing very respectable results in 6.5CM
1x Hornady brass (FL sized, trimmed, chamfered, deburred, etc)
140 Barnes Match Burner @ 2.203" to ogive
CCI BR2 primer
42.0 grains of Reloder 16
Testing started in the morning at 54º, up to 62º in the afternoon, 6931' ASL, 23.50 inHg
Velocity was really good at 2847 fps, SD of 7.4, ES of 20 measured with a MagnetoSpeed V3
Here's the link with some more info, including a comparison between an equal load of H4350 and RL16
http://www.scout.com/military/snipe...ng/15114591-6-5cm-reloder-16-load-development
Premium Member
First Sergeant
Rating: 3.4/5 this site
1360 posts this site
Re: 6.5 Creedmoor
10/06/2016 Last edited 10/06/2016 by KibaSH
Anyone playing with RL16 yet? Alliant's test data is showing higher velocities at the same pressure, lower SD, and less temperature sensitivity compared to the old standby of H4350. Density of RL16 is slightly lower than H4350 so it takes a little more RL16 compared to H4350 to match the pressures but the data looks really good.
Early reports on other forums are very promising regarding velocity/SD/accuracy.
Even though I'm sitting on quite a bit of H4350 I have some RL16 on the way and will be testing with it soon. Just wondered if anyone else on here is already experimenting with it...
Rate now:
Ed043XPrivate
Rating: 0.0/5 this site
1 posts this site
Re: 6.5 Creedmoor
10/08/2016
I'm new to the 6.5 but not new to reloading. What do y'all recommend for 120 gr Speer SP and a Ruger American? I just got it and haven't had a chance to check the OAl or anything. I did however put 60 rounds thru it using the Hornady Match 120 gr A-max and are loving the results. I'm getting 1 1/2" to 2" groups at 300 yards.
I'm looking forward to being on this site and looking around.
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
10/09/2016 Last edited 10/17/2016 by CaneZach
Barnes 140 Match Burner
2.214" to ogive
1x Hornady brass
41.9 grains H4350
FGM210M primers
26" DTA barrel with SilencerTech suppressor
Avg MV 2806, ES 20, SD 8.4
70°, 5660' asl, 24.66 inHg
Today was the first time I tried these bullets. Advertised G1 of 0.586 was REAL close and Ballistic AE G7 drag model gave me a 0.293 G7. Called for 8.14 mils of elevation to get to 1080 yards. I needed 8.2 to get on target, so pretty damn close to advertised. I still want to play around with seating depth to tighten up the groups, but it really looks promising.
Rate now:
DaveThomas83XSergeant
Rating: 3.0/5 this site
278 posts this site
Re: 6.5 Creedmoor
10/10/2016
I've seen some RL17 loads here and there, it seems to be slightly more available in my area so I picked up a pound to work into some load dev. Seems like 40-41gr is the sweet spot for alot of you, hopefully it will be the same for me.
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
10/10/2016 Last edited 10/10/2016 by CaneZach
DaveThomas83 wrote:
I've seen some RL17 loads here and there, it seems to be slightly more available in my area so I picked up a pound to work into some load dev. Seems like 40-41gr is the sweet spot for alot of you, hopefully it will be the same for me.
I really like RL17 in my 6.5 loads. As you said, it seems to be more available in my area as well and it's performed really well for me. Granted, I've read all the reports about its temperature sensitivity, but I did my load work in the middle of summer when the temps were in the 90s or higher. For 140 grain projectiles, the node does seem to fall somewhere between 40 and 41 grains, but work up safely, your results may vary, and all the other legal stuff.I've seen some RL17 loads here and there, it seems to be slightly more available in my area so I picked up a pound to work into some load dev. Seems like 40-41gr is the sweet spot for alot of you, hopefully it will be the same for me.
Edit: For what it's worth, I get better velocities with RL17 while using less powder than H4350. Not an apples to apples comparison, but I use 41.9 grains of H4350 with the Barnes 140 Match Burner and my MV is 2806. With 40.4 grains of RL17 and a Hornady 140 BTHP, I was in the 2850 range
Rate now:
PalmettoPride29412
XGunny Sergeant
Rating: 3.4/5 this site
518 posts this site
Re: 6.5 Creedmoor
11/05/2016
Anybody got a load for Hornady's new .264/6.5mm 147gr ELD Match bullet? I just ordered 200 from Midway.
Rate now:
erslllXSergeant
Rating: 3.0/5 this site
107 posts this site
Re: 6.5 Creedmoor
11/05/2016
I am surprised that Midway has the 147gr already.
Anyone with 143gr ELD-X load info?
Rate now:
CaneZach
XSergeant
Rating: 3.4/5 this site
391 posts this site
Re: 6.5 Creedmoor
11/06/2016
I think this might be the first Reloder 16 load in this thread, so hopefully we'll see a few more. I've found, in limited testing, that Reloder 16 is producing very respectable results in 6.5CM
1x Hornady brass (FL sized, trimmed, chamfered, deburred, etc)
140 Barnes Match Burner @ 2.203" to ogive
CCI BR2 primer
42.0 grains of Reloder 16
Testing started in the morning at 54º, up to 62º in the afternoon, 6931' ASL, 23.50 inHg
Velocity was really good at 2847 fps, SD of 7.4, ES of 20 measured with a MagnetoSpeed V3
Here's the link with some more info, including a comparison between an equal load of H4350 and RL16
http://www.scout.com/military/snipe...ng/15114591-6-5cm-reloder-16-load-development
G
Guest
Guest
RoterJager
XGunny Sergeant
Rating: 3.1/5 this site
549 posts this site
Re: 6.5 Creedmoor
11/07/2016
(1 vote)
Anyone have a good recipe for Hornady 143 ELD-X and H4350?
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
11/08/2016 Last edited 11/08/2016 by towboater91
I too have had good results with reloder 16 this past couple weeks. My current load is
42.4/42.5 reloder 16 measured with rcbs 1010 scale
Hornady brass 3x fired, trimmed to 1.905 deburred and chamfered, cleaned with thumblers tumbler with stainless media
Hornady bthp 140gr loaded at 2.800 OAL, 2.205 to ogive (2.250 touching lands, using OAL gauge and comparator)
CCI 200 primers (can't find gm210m or cci br2 primers anywhere!)
Used redding type S match dies
Micro seating die and neck die with .289 bushing. Also have a .290 bushing to try soon. Shooting out of a savage 12 with 26" criterion barrel. I've had pretty good results with these powders so far.
Reloder 16
Reloder17
H4350
Imr4350
Imr4451, all in the 42gr range.
I don't feel like the cci 200 primers are very consistent tho, does anyone else have this opinion?
Rate now:
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
11/09/2016
no problems with CCI 200s...all i run in 6comp, 6.5creed, and 308, thousands of rounds...single digit SDs and bugholes in all
Rate now:
drglockXGunny Sergeant
Rating: 3.2/5 this site
580 posts this site
Re: 6.5 Creedmoor
11/12/2016 Last edited 11/12/2016 by drglock
Trued 700
Bartlien 1-8.5 @ 18"
TBAC Ultra 9
140gr Amax's
H4350 42.6grs
FGM LR
Hornady brass
BTO 2.200 .014 off lands
.249 group
[IMG2=JSON]{"alt":" photo IMG_0276_zpsyon1plga.jpg","data-align":"none","data-size":"full","src":"http:\/\/i298.photobucket.com\/albums\/mm274\/deathwishafs\/Mobile%20Uploads\/IMG_0276_zpsyon1plga.jpg"}[/IMG2]
That low of a SD was just luck , all the planets must of been aligned.
Rate now:
Deiser1245XPrivate
Rating: 0.0/5 this site
8 posts this site
Re: 6.5 Creedmoor
11/22/2016
120ttsx
40.4gr Varget
CCI200
Norma Brass
2.21 to ogive
3004 fps
130 VLD
41.7gr IMR4451
CCI200
Norma Brass
2.17 to ogive
2710 fps
127LRX
41.5gr IMR4451
CCI200
Norma Brass
2.23 to ogive
2830 fps
I'm trying to stay away from H4350 due to its unavailability these days. Anyone else have good luck with varget or 4451 in the 120's and 130's? Varget gave some excellent groups with the 130 VLD's but velocity wasn't there so i didn't post the load.
Rate now:
barrows23XPrivate
Rating: 0.0/5 this site
8 posts this site
Re: 6.5 Creedmoor
11/23/2016
I'm using:
RL-26 49 grains
Hornady brass
140gr ELD-Match
2.240" to ogive
CCI BR-2 primers
MV 2925fps in 22" bbl
SD 11
ES 19
1/4 MOA
Rate now:
varmintkillerXPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
11/29/2016
I am getting tighter groups with 41.0 gr of H4350 with the 143 ELD-X than I was with 41.5. Shooting is out of a stock savage lrp rifle but suppressed. Velocity was around 2775 using a chrony. Im at 4280 elevation.
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
12/11/2016 Last edited 12/11/2016 by towboater91
These are all from today with the 6.5 cm
1st pic is hornady 140gr match bthp 42.6 imr4451 2.222 to ogive .030 thou off lands
2nd pic is lapua 139gr scenar 42.4 imr4451 2.255 .020 thou off lands
3rd pic is nosler competition bthp 42.4 imr4451 2.239 .020 thou off lands
All with hornady brass neck sized .289 bushing
CCI 200 primers
5 shot groups at 100yds except first pic was 4 shots at 100
Rate now:
Upst8co
XPrivate
Rating: 3.2/5 this site
35 posts this site
Re: 6.5 Creedmoor
12/14/2016 Last edited 12/14/2016 by Upst8co
Lots of great information comes from this site. Found This thread and it will come in very useful as I just picked up a Ruger Precision in the 6.5 . Thanks for all the great data !
Rate now:
eldest584XPrivate
Rating: 0.0/5 this site
5 posts this site
Re: 6.5 Creedmoor
12/14/2016
what kind of velocity were you getting with the hodgdon hybrid 100v for your 6.5? I have been having a hell of a time getting my hands on h4350 and looking at the hodgdon website the 100v has looked pretty solid.
Rate now:
SixfivesavageXFirst Sergeant
Rating: 3.2/5 this site
1250 posts this site
Re: 6.5 Creedmoor
12/15/2016
What G7 BC are you seeing the best results from? I'm having trouble getting good dope from my kestrel and I trust my velocity from a magnetospeed.
Rate now:
bigbullsXPrivate
Rating: 0.0/5 this site
5 posts this site
Re: 6.5 Creedmoor
12/20/2016
Tag
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
12/22/2016
Has anyone tried any nosler brass or norma brass with their creedmoor? If so could you tell a difference between that and hornady brass?
Rate now:
erslllXSergeant
Rating: 3.0/5 this site
107 posts this site
Re: 6.5 Creedmoor
12/28/2016 Last edited 12/28/2016 by erslll
Rate now:
drglockXGunny Sergeant
Rating: 3.2/5 this site
580 posts this site
Re: 6.5 Creedmoor
01/02/2017
Berger 140gr VLD-H
.308 Palma brass converted to 6.5 CM
CCI Small Rifle Mag
IMR4451 42.4grs
BTO 2.193
.264 group
MV 2615fps out 18" barrel
Rate now:
bustedreticleXPrivate
Rating: 3.0/5 this site
30 posts this site
Re: 6.5 Creedmoor
01/12/2017
Since there's not a lot of reloder 16 data here's what I found:
Berger 130 AR hybrid
44.2 Reloder 16
Hornady brass (new)
COAL 2.79
MV Average 2820 (22" barrel) Remington 700 (5 shots)
SD 6
ES 15
I don't have an pics but the first 3 shots where through the same hole but I pulled the last two shots
Rate now:
65madmanXPrivate
Rating: 3.0/5 this site
42 posts this site
Re: 6.5 Creedmoor
01/12/2017
Tag, For data.
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
01/16/2017
Hmmmmmmm, am still waiting for someone to reply to a post a few pages ago, about using Accurate 4350 in the 6.5CM.
Rate now:
MarinePMI
XFirst Sergeant
Rating: 3.6/5 this site
2100 posts this site
Re: 6.5 Creedmoor
01/17/2017
I believe JGlasgow did, on page 8.
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
01/17/2017
Thanks MarinePMI, I missed Glasgow's post. Odd that Accurate shows no load data for their 4350 in the 6.5 CM. Picked up a lb. of it today, to try.
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
01/18/2017
Here is Accurate's reply to my request fo 6.5CM load data for their 4350 powder.
120gr.....start load 40gr.........max load 45 gr.....103% compacted
129gr.....start load 40gr.........max load 44.5gr....103% compacted
140gr.....start load 39.2gr.....max load 43.5gr.....103% compacted
Rate now:
catfish18XCorporal
Rating: 0.0/5 this site
50 posts this site
Re: 6.5 Creedmoor
01/23/2017
135 berger classic hunter .01 off lands
Alpha brass, fed 210m, 47 grains viht n560
2850 fps with an SD of 4
Shoots in the .1's and .2's out of my accurate ordnance built lightweight hunter
Barrel is a 24 inch 8 twist rock creek #5
Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2054 posts this site
Re: 6.5 Creedmoor
01/27/2017
Rate now:
david59XCorporal
Rating: 3.0/5 this site
56 posts this site
Re: 6.5 Creedmoor
Saturday at 8:25 PM
Any data using Superperformance?
Or Ramshot Hunter?
I have 130 VLDs and 143 ELD-X
Rate now:
HawaiianKansasXPrivate
Rating: 0.0/5 this site
8 posts this site
Re: 6.5 Creedmoor
Saturday at 11:10 PM
TAG
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
Yesterday at 7:22 PM
JGlasgow, Accurates reply:
24" barrel, 1-9"twist, WLR primer, and case was HORNADY
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
Yesterday at 7:31 PM Last edited Yesterday at 7:34 PM by huffmanite
david59, if you check load data site for Accurate/Ramshot powders, you'll not find the bullets you have listed for the HUNTER powder loads. Here is the Ramshot data for similar grain bullets.
123 gr Sierra MK 42.3 start.......47 max
140 gr Hdy A-max 40.8 start........45.3 max
142 gr Sierra MK 41.1 start........45.7 max
By the way, love the way the Ramshot rifle powders meter for me and keep five of them for my reloading.
Rate now:
david59XCorporal
Rating: 3.0/5 this site
56 posts this site
Re: 6.5 Creedmoor
Yesterday at 11:32 PM
Thanks
XGunny Sergeant
Rating: 3.1/5 this site
549 posts this site
Re: 6.5 Creedmoor
11/07/2016
(1 vote)
Anyone have a good recipe for Hornady 143 ELD-X and H4350?
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
11/08/2016 Last edited 11/08/2016 by towboater91
I too have had good results with reloder 16 this past couple weeks. My current load is
42.4/42.5 reloder 16 measured with rcbs 1010 scale
Hornady brass 3x fired, trimmed to 1.905 deburred and chamfered, cleaned with thumblers tumbler with stainless media
Hornady bthp 140gr loaded at 2.800 OAL, 2.205 to ogive (2.250 touching lands, using OAL gauge and comparator)
CCI 200 primers (can't find gm210m or cci br2 primers anywhere!)
Used redding type S match dies
Micro seating die and neck die with .289 bushing. Also have a .290 bushing to try soon. Shooting out of a savage 12 with 26" criterion barrel. I've had pretty good results with these powders so far.
Reloder 16
Reloder17
H4350
Imr4350
Imr4451, all in the 42gr range.
I don't feel like the cci 200 primers are very consistent tho, does anyone else have this opinion?
Rate now:
morganlamprechtXFirst Sergeant
Rating: 3.8/5 this site
1312 posts this site
Re: 6.5 Creedmoor
11/09/2016
no problems with CCI 200s...all i run in 6comp, 6.5creed, and 308, thousands of rounds...single digit SDs and bugholes in all
Rate now:
drglockXGunny Sergeant
Rating: 3.2/5 this site
580 posts this site
Re: 6.5 Creedmoor
11/12/2016 Last edited 11/12/2016 by drglock
Trued 700
Bartlien 1-8.5 @ 18"
TBAC Ultra 9
140gr Amax's
H4350 42.6grs
FGM LR
Hornady brass
BTO 2.200 .014 off lands
.249 group
[IMG2=JSON]{"alt":" photo IMG_0276_zpsyon1plga.jpg","data-align":"none","data-size":"full","src":"http:\/\/i298.photobucket.com\/albums\/mm274\/deathwishafs\/Mobile%20Uploads\/IMG_0276_zpsyon1plga.jpg"}[/IMG2]
That low of a SD was just luck , all the planets must of been aligned.
Rate now:
Deiser1245XPrivate
Rating: 0.0/5 this site
8 posts this site
Re: 6.5 Creedmoor
11/22/2016
120ttsx
40.4gr Varget
CCI200
Norma Brass
2.21 to ogive
3004 fps
130 VLD
41.7gr IMR4451
CCI200
Norma Brass
2.17 to ogive
2710 fps
127LRX
41.5gr IMR4451
CCI200
Norma Brass
2.23 to ogive
2830 fps
I'm trying to stay away from H4350 due to its unavailability these days. Anyone else have good luck with varget or 4451 in the 120's and 130's? Varget gave some excellent groups with the 130 VLD's but velocity wasn't there so i didn't post the load.
Rate now:
barrows23XPrivate
Rating: 0.0/5 this site
8 posts this site
Re: 6.5 Creedmoor
11/23/2016
I'm using:
RL-26 49 grains
Hornady brass
140gr ELD-Match
2.240" to ogive
CCI BR-2 primers
MV 2925fps in 22" bbl
SD 11
ES 19
1/4 MOA
Rate now:
varmintkillerXPrivate
Rating: 0.0/5 this site
2 posts this site
Re: 6.5 Creedmoor
11/29/2016
I am getting tighter groups with 41.0 gr of H4350 with the 143 ELD-X than I was with 41.5. Shooting is out of a stock savage lrp rifle but suppressed. Velocity was around 2775 using a chrony. Im at 4280 elevation.
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
12/11/2016 Last edited 12/11/2016 by towboater91
These are all from today with the 6.5 cm
1st pic is hornady 140gr match bthp 42.6 imr4451 2.222 to ogive .030 thou off lands
2nd pic is lapua 139gr scenar 42.4 imr4451 2.255 .020 thou off lands
3rd pic is nosler competition bthp 42.4 imr4451 2.239 .020 thou off lands
All with hornady brass neck sized .289 bushing
CCI 200 primers
5 shot groups at 100yds except first pic was 4 shots at 100
Rate now:
Upst8co
XPrivate
Rating: 3.2/5 this site
35 posts this site
Re: 6.5 Creedmoor
12/14/2016 Last edited 12/14/2016 by Upst8co
Lots of great information comes from this site. Found This thread and it will come in very useful as I just picked up a Ruger Precision in the 6.5 . Thanks for all the great data !
Rate now:
eldest584XPrivate
Rating: 0.0/5 this site
5 posts this site
Re: 6.5 Creedmoor
12/14/2016
what kind of velocity were you getting with the hodgdon hybrid 100v for your 6.5? I have been having a hell of a time getting my hands on h4350 and looking at the hodgdon website the 100v has looked pretty solid.
Rate now:
SixfivesavageXFirst Sergeant
Rating: 3.2/5 this site
1250 posts this site
Re: 6.5 Creedmoor
12/15/2016
What G7 BC are you seeing the best results from? I'm having trouble getting good dope from my kestrel and I trust my velocity from a magnetospeed.
Rate now:
bigbullsXPrivate
Rating: 0.0/5 this site
5 posts this site
Re: 6.5 Creedmoor
12/20/2016
Tag
Rate now:
towboater91XPrivate
Rating: 0.0/5 this site
22 posts this site
Re: 6.5 Creedmoor
12/22/2016
Has anyone tried any nosler brass or norma brass with their creedmoor? If so could you tell a difference between that and hornady brass?
Rate now:
erslllXSergeant
Rating: 3.0/5 this site
107 posts this site
Re: 6.5 Creedmoor
12/28/2016 Last edited 12/28/2016 by erslll
RoterJager wrote:
Anyone have a good recipe for Hornady 143 ELD-X and H4350?
42.5 gr of H4350 has been working pretty well for me, .015-.020 off the lands. CCI250 primers, Horandy brassAnyone have a good recipe for Hornady 143 ELD-X and H4350?
Rate now:
drglockXGunny Sergeant
Rating: 3.2/5 this site
580 posts this site
Re: 6.5 Creedmoor
01/02/2017
Berger 140gr VLD-H
.308 Palma brass converted to 6.5 CM
CCI Small Rifle Mag
IMR4451 42.4grs
BTO 2.193
.264 group
MV 2615fps out 18" barrel
Rate now:
bustedreticleXPrivate
Rating: 3.0/5 this site
30 posts this site
Re: 6.5 Creedmoor
01/12/2017
Since there's not a lot of reloder 16 data here's what I found:
Berger 130 AR hybrid
44.2 Reloder 16
Hornady brass (new)
COAL 2.79
MV Average 2820 (22" barrel) Remington 700 (5 shots)
SD 6
ES 15
I don't have an pics but the first 3 shots where through the same hole but I pulled the last two shots
Rate now:
65madmanXPrivate
Rating: 3.0/5 this site
42 posts this site
Re: 6.5 Creedmoor
01/12/2017
Tag, For data.
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
01/16/2017
Hmmmmmmm, am still waiting for someone to reply to a post a few pages ago, about using Accurate 4350 in the 6.5CM.
Rate now:
MarinePMI
XFirst Sergeant
Rating: 3.6/5 this site
2100 posts this site
Re: 6.5 Creedmoor
01/17/2017
I believe JGlasgow did, on page 8.
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
01/17/2017
Thanks MarinePMI, I missed Glasgow's post. Odd that Accurate shows no load data for their 4350 in the 6.5 CM. Picked up a lb. of it today, to try.
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
01/18/2017
Here is Accurate's reply to my request fo 6.5CM load data for their 4350 powder.
120gr.....start load 40gr.........max load 45 gr.....103% compacted
129gr.....start load 40gr.........max load 44.5gr....103% compacted
140gr.....start load 39.2gr.....max load 43.5gr.....103% compacted
Rate now:
catfish18XCorporal
Rating: 0.0/5 this site
50 posts this site
Re: 6.5 Creedmoor
01/23/2017
135 berger classic hunter .01 off lands
Alpha brass, fed 210m, 47 grains viht n560
2850 fps with an SD of 4
Shoots in the .1's and .2's out of my accurate ordnance built lightweight hunter
Barrel is a 24 inch 8 twist rock creek #5
Rate now:
JGlasgowXFirst Sergeant
Rating: 3.4/5 this site
2054 posts this site
Re: 6.5 Creedmoor
01/27/2017
huffmanite wrote:
Here is Accurate's reply to my request fo 6.5CM load data for their 4350 powder.
120gr.....start load 40gr.........max load 45 gr.....103% compacted
129gr.....start load 40gr.........max load 44.5gr....103% compacted
140gr.....start load 39.2gr.....max load 43.5gr.....103% compacted
Did they specify what brand case?Here is Accurate's reply to my request fo 6.5CM load data for their 4350 powder.
120gr.....start load 40gr.........max load 45 gr.....103% compacted
129gr.....start load 40gr.........max load 44.5gr....103% compacted
140gr.....start load 39.2gr.....max load 43.5gr.....103% compacted
Rate now:
david59XCorporal
Rating: 3.0/5 this site
56 posts this site
Re: 6.5 Creedmoor
Saturday at 8:25 PM
Any data using Superperformance?
Or Ramshot Hunter?
I have 130 VLDs and 143 ELD-X
Rate now:
HawaiianKansasXPrivate
Rating: 0.0/5 this site
8 posts this site
Re: 6.5 Creedmoor
Saturday at 11:10 PM
TAG
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
Yesterday at 7:22 PM
JGlasgow, Accurates reply:
24" barrel, 1-9"twist, WLR primer, and case was HORNADY
Rate now:
huffmaniteXCorporal
Rating: 0.0/5 this site
90 posts this site
Re: 6.5 Creedmoor
Yesterday at 7:31 PM Last edited Yesterday at 7:34 PM by huffmanite
david59, if you check load data site for Accurate/Ramshot powders, you'll not find the bullets you have listed for the HUNTER powder loads. Here is the Ramshot data for similar grain bullets.
123 gr Sierra MK 42.3 start.......47 max
140 gr Hdy A-max 40.8 start........45.3 max
142 gr Sierra MK 41.1 start........45.7 max
By the way, love the way the Ramshot rifle powders meter for me and keep five of them for my reloading.
Rate now:
david59XCorporal
Rating: 3.0/5 this site
56 posts this site
Re: 6.5 Creedmoor
Yesterday at 11:32 PM
Thanks
Haven't seen much on IMR 4451 so I thought Id post my results.
Bullet: Hornady 140gn ELDM
Brass: Hornady
Primer: Federal 210
Charge Weight: 42.1 gn
Avg fps: 2744
SD: 7
Shot out of an RPR with a 24 inch bartlein .02 off the lands. Produced half MOA group.
Bullet: Hornady 140gn ELDM
Brass: Hornady
Primer: Federal 210
Charge Weight: 42.1 gn
Avg fps: 2744
SD: 7
Shot out of an RPR with a 24 inch bartlein .02 off the lands. Produced half MOA group.
Last edited:
DTA SRS 26" 1:8 twist
Silencer Tech suppressor
Nosler 140 RDFs at 2.203" to ogive
41.2 grains Reloder 16
CCI BR2 primers
Hornady twice fired brass
Avg MV: 2856 fps (Magnetospeed V3)
ES: 4
SD: 1.49
Yeah, I know those spread and dev numbers are pure luck, planets aligning, etc., but I'll take them for today! I tested 41.2, 41.5, and 41.8 grains. Avg MVs of 41.5 and 41.8 were excellent (2871 and 2887, respectively). SDs were under 10, and ES was low for 41.5, but at 41.8 the spread was 23 fps and groups started opening up. No pressure signs on the brass itself at 41.5 grains. Slight flattening and cratering at 41.8 grains.
Silencer Tech suppressor
Nosler 140 RDFs at 2.203" to ogive
41.2 grains Reloder 16
CCI BR2 primers
Hornady twice fired brass
Avg MV: 2856 fps (Magnetospeed V3)
ES: 4
SD: 1.49
Yeah, I know those spread and dev numbers are pure luck, planets aligning, etc., but I'll take them for today! I tested 41.2, 41.5, and 41.8 grains. Avg MVs of 41.5 and 41.8 were excellent (2871 and 2887, respectively). SDs were under 10, and ES was low for 41.5, but at 41.8 the spread was 23 fps and groups started opening up. No pressure signs on the brass itself at 41.5 grains. Slight flattening and cratering at 41.8 grains.
