Accessories FS: Savage bolt lift kits

[Dolomite_Supafly]

$25 shipped

​

Every kit sold comes with a 100% money back guarantee. If they do not work, you do not like it or just don't want it, return it and I will refund 100% of your money including shipping which is $1. If you ask for a refund you will get a refund, no questions asked.

The kit is made in the US from 303 stainless so they will not rust. The ball bearing is a Rockwell C80 so they will not wear and should last forever. This kit takes the normally rough Savage bolt lift feel smoother. These do not require any modification to the gun. No need to trim or space the Bolt Action Screw (BAS). These are ready to go, you do not need to buy anything other than a 1/4" allen wrench to remove the BAS at the rear of the bolt.



These WILL work on the Lapua Magnum action, any model 1X/11X with an allen wrench screw at the rear of the bolt but without the cocked indicator.

They will ***NOT*** work on Savages with the cocking indicator in the bolt or the Axis or Fusion or any Savage with flat tip screw slot at the rear of the bolt. If you have a F or J action these will not work. If you have any doubt you can measure the screw at the back of the bolt. If the threaded part of that screw is ~.500" these should work.

Always a positive feedback. 100% guaranteed.

 

[tcamel4]

I got a Savage 10 with the fatter factory bolt handle. If this fits I'll take one. Sending pm.

 

[IowaPlinker]

Pm sent

 

[TxWelder35]

Got one on the last run. Seller is g2g and the lift kit works well

 

[Dolomite_Supafly]

All kits are in the mail.

Thanks guys.

 

[AWD4416]

pm sent

 

[Dolomite_Supafly]

Bumpity bump

 

[Dolomite_Supafly]

Bump

 

[BoltActionBrotherhood]

WILL THIS work on a savage 338 lapua, the elite precision model? I thought there was a coking indicator but not sure.

 

[Dolomite_Supafly]

WILL THIS work on a savage 338 lapua, the elite precision model? I thought there was a coking indicator but not sure.

You can see the cocked indicator at the rear of the bolt. If you have a button at the rear of the bolt that drops when you fire my bolt lift kit will not work. If the screw at the rear of the bolt has no hole through the middle for the cocked indicator then my kit will work.

 

[Dolomite_Supafly]

I have a few more left to sell, when they are gone they are gone.

No plans on making these ever again.

 

[Rocketvapor]

Just a technical question.
How much thickness (internal length) does your kit add.
Flange plus ball height?

BTW, this does seem to be better than the thrust bearing kit for reducing bolt lift

 

[Dolomite_Supafly]

Just a technical question.
How much thickness (internal length) does your kit add.
Flange plus ball height?

BTW, this does seem to be better than the thrust bearing kit for reducing bolt lift

Minimal, there is no need to reduce the length of the Bolt Action Screw with this kit.

Additionally, it has been tested against the thrust bearing version and this one results in a more favorable bolt lift.

 

[Rocketvapor]

No question on being better than the thrust bearing kit.
And, those with a cocking indicator pin can probably replace BAS and pin and use your idea.

Sorry about jumping in on your thread.

 

[Ramfan2500]

PM sent

 

[Steelsmasher71]

PM sent

 

[Dolomite_Supafly]

No question on being better than the thrust bearing kit.
And, those with a cocking indicator pin can probably replace BAS and pin and use your idea.

Sorry about jumping in on your thread.

It has been tested both scientifically as well as by popular opinion.

I only have 3 left, if you are on the fence this is the time. Not sure who else sells this type anymore.

Since I wont be selling these any more might as well tell the story why I made them. I was in a helicopter accident that partially paralyzed me. I laid in bed 20+ hours a day because walking was very difficult. After a few years I was getting better and looking for something to do so I started making bolt lift kits out of 38 special cases that I threaded for a setscrew. I made a LOT of those and gave them away becaus my benefit was in making them. As I got better I moved onto other things and quit making the bolt lift kits out of cases. Every week I was getting emails from the various boards I gave them away on, all were asking if I could make them. So I had some made and here we are with only three left.

Thanks to everyone who has purchased from me and they still have a no questions asked money back guarantee.

 

[smax]

PM sent

 

[Dolomite_Supafly]

Sold out, thanks again.

 

[NDshooter75]

PM sent