- Thread starter mark5pt56
- Start date
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
24-24.5 varget and 2.45" long.
24-24.5 varget and 2.45" long.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
I shoot 80gr Amax and 80gr Noslers. 24.5gr Varget shoots good for both bullets.
I'm currently shooting a douglas barrel, it likes to jump the Amax about .020 and the Noslers about .010.
Both are very accurate loads but the Amax will flat out-shoot the Noslers or the SMK's.
I shoot 80gr Amax and 80gr Noslers. 24.5gr Varget shoots good for both bullets.
I'm currently shooting a douglas barrel, it likes to jump the Amax about .020 and the Noslers about .010.
Both are very accurate loads but the Amax will flat out-shoot the Noslers or the SMK's.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
RRA NMA2, 24 grains of Varget and 77 SMK's 2700 fps. 24.5 for 2750. I shoot the 24 grain load for Service Rifle.
RRA NMA2, 24 grains of Varget and 77 SMK's 2700 fps. 24.5 for 2750. I shoot the 24 grain load for Service Rifle.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
CLE, 20" Krieger 1:7.7
24gr Varget and 80amax on lands. 24.5 is possible, but primers are FLAT.
This load goes into the 10 ring if you aim it there....which I often don't.
I definitely need less wind than folks with 77smk and 75amax.
CLE, 20" Krieger 1:7.7
24gr Varget and 80amax on lands. 24.5 is possible, but primers are FLAT.
This load goes into the 10 ring if you aim it there....which I often don't.
I definitely need less wind than folks with 77smk and 75amax.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
This sounds good, I think I will try the AMAX when I start up on this again. I did have a RRA years ago and used Hornady 75 BTHP's. Forget the charge weight with Varget, but they were warm, so warm I would get doubles on the light trigger. I need to find a dang rifle first!
Wanted an off the shelf one, Armalite? The RRA I got from Legal Transfers required 7 minutes of windage to zero, front sight was canted badly and I don't want to give them another try.
FFL checked with Jerry's and they are out.
Mark
This sounds good, I think I will try the AMAX when I start up on this again. I did have a RRA years ago and used Hornady 75 BTHP's. Forget the charge weight with Varget, but they were warm, so warm I would get doubles on the light trigger. I need to find a dang rifle first!
Wanted an off the shelf one, Armalite? The RRA I got from Legal Transfers required 7 minutes of windage to zero, front sight was canted badly and I don't want to give them another try.
FFL checked with Jerry's and they are out.
Mark
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
Mark,
Check out the reloading depot located in the upper section of this forum...there are a plethora of loads for 556s covering the bullets you listed and almost all common powders.
Mark,
Check out the reloading depot located in the upper section of this forum...there are a plethora of loads for 556s covering the bullets you listed and almost all common powders.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
1/8 wylde 20" RRA 75amax 2975fps 25gr varget 2.5 coal and 69 smk 2800 fps 24.6 varget mag length
1/8 wylde 20" RRA 75amax 2975fps 25gr varget 2.5 coal and 69 smk 2800 fps 24.6 varget mag length
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
24.5 varget with 80 SMK as long as possible.
24.5 varget with 80 SMK as long as possible.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
80-Amax 23.4 Varget 2.49" I was cratering primers at 24.0. Similar load for SMK
80-Amax 23.4 Varget 2.49" I was cratering primers at 24.0. Similar load for SMK
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
I had a post about this recently and compared the 68-69's to the 77's. The balistics were pretty suprising.
For 600 yards I would think the 68-69's would be the way to go/ Plus they are mag fed
I had a post about this recently and compared the 68-69's to the 77's. The balistics were pretty suprising.
For 600 yards I would think the 68-69's would be the way to go/ Plus they are mag fed
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
I am currently starting development for a 24" 1:8" heavy barrel AR (Stag model 6). My initial loads will be 69SMK/24.5gr Varget, and HDY 75gr HPBT Match/24.0gr Varget. Whatever it takes to shoot under 1MOA for 40 scoring rounds at 250yd in calm conditions will suit my needs. That is also a fairly tall order, but I've noticed that some of my competitors have begun to manage it, so I'm obliged to meet that challenge.
I am fairly certain that any load which meets this standard at 250yd will still be competitive out of my barrel at distances like the 600yd you mention.
I will be comparing these handloads against the Prvi 69 and 75gr factory Match loads that my rifle already shows some liking for. The Prvi is pretty good stuff, and the cost is low enough at a little over $.55-.60 a round that the time its saves makes it suitible for practice ammo. The Prvi match ammo's brass has proven to be excellent for reloading.
Greg
I am currently starting development for a 24" 1:8" heavy barrel AR (Stag model 6). My initial loads will be 69SMK/24.5gr Varget, and HDY 75gr HPBT Match/24.0gr Varget. Whatever it takes to shoot under 1MOA for 40 scoring rounds at 250yd in calm conditions will suit my needs. That is also a fairly tall order, but I've noticed that some of my competitors have begun to manage it, so I'm obliged to meet that challenge.
I am fairly certain that any load which meets this standard at 250yd will still be competitive out of my barrel at distances like the 600yd you mention.
I will be comparing these handloads against the Prvi 69 and 75gr factory Match loads that my rifle already shows some liking for. The Prvi is pretty good stuff, and the cost is low enough at a little over $.55-.60 a round that the time its saves makes it suitible for practice ammo. The Prvi match ammo's brass has proven to be excellent for reloading.
Greg
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
24.8gr Varget behind HbN coated 80gr SMK. OAL 2.450"
24.8gr Varget behind HbN coated 80gr SMK. OAL 2.450"
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
CLE upper (w/Frank's chamber) Krieger 1/7.7 24 Varget 80 SMK 0.035 jump. Wolf primer, Nosler custom brass (11 firings). Will shoot ~1 MOA prone/sling over 20 shots (shot a 200 with 19X this morning at 300 yards).
CLE upper (w/Frank's chamber) Krieger 1/7.7 24 Varget 80 SMK 0.035 jump. Wolf primer, Nosler custom brass (11 firings). Will shoot ~1 MOA prone/sling over 20 shots (shot a 200 with 19X this morning at 300 yards).
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
I use 80 gr smk over 24 gr of varget
I use 80 gr smk over 24 gr of varget
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: aloreman</div><div class="ubbcode-body">I use 80 gr smk over 24 gr of varget </div></div>
This one...All I ever used.
<div class="ubbcode-block"><div class="ubbcode-header">Originally Posted By: aloreman</div><div class="ubbcode-body">I use 80 gr smk over 24 gr of varget </div></div>
This one...All I ever used.
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
24.5 Varget over 77gr SMK, 69gr SMK, Long Range loaded long 75gr A-Max, 80gr SMK
24.5 Varget over 77gr SMK, 69gr SMK, Long Range loaded long 75gr A-Max, 80gr SMK
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
I use 23.5 grs of RE-15 with an 80 gr SMK at the 600. For the 200 and 300 I use the 69 SMK with 24.5 grs of RE-15. The upper is a RRA NM 1/8".
I use 23.5 grs of RE-15 with an 80 gr SMK at the 600. For the 200 and 300 I use the 69 SMK with 24.5 grs of RE-15. The upper is a RRA NM 1/8".
Re: HIGH POWER LOAD FOR .223 @600 SMK OR AMAX
75 vld, jumped .035, 24.2 H4895. Any case or primer will do. This is Basically what AMU is shooting at 600. Also try jumping those 80's a little bit more and see what happens...
either the Sierra or the hornady. You might be suprised what your barrel/chamber likes. .018 is an answer, but it isn't the only one.
75 vld, jumped .035, 24.2 H4895. Any case or primer will do. This is Basically what AMU is shooting at 600. Also try jumping those 80's a little bit more and see what happens...
