Nosler brass quality…
- Thread starter DubfromGA
- Start date
Ive only used it in a hunting 270 but it beats the piss out of the winchester brass I was using before. I like it.
- Nov 3, 2010
- 10,820
- 24,079
- Nov 3, 2010
- 10,820
- 24,079
To be fair I reckon, the gasser Noslers were bad for tearing up brass from what I have read and heard. Maybe not a fair comparison to use a case with a rebated head compared to a standard case. Iffin I read right and understand right, rebated case heads are a weak point in brass design and can lead to damage easier. Somebody can add to or correct me if I am far off the plotted course.
I think it really depends on what caliber you are buying.
Most of the Nosler brass i have used has been the Nosler Custom brass ( 308win, 243win, 270win, 300wm) its very high quality and fulled prepped and weight sorted but overly expensive in my opinion.
It is also all made by Norma unless something has changed.
Some of or most of the AR stuff is mostlikely made by Nosler on SSA machinery and tooling since Nosler bought them out.
Most of the Nosler brass i have used has been the Nosler Custom brass ( 308win, 243win, 270win, 300wm) its very high quality and fulled prepped and weight sorted but overly expensive in my opinion.
It is also all made by Norma unless something has changed.
Some of or most of the AR stuff is mostlikely made by Nosler on SSA machinery and tooling since Nosler bought them out.
Depends on the cartridge. Availability of certain cartridges and overall availability for purchase seems to be good. Is this your criteria? I dont think its lapua or peterson quality.
Only have a couple firings on my first try with Nosler 6.5 Creedmor Brass, but so far so good. I do anneal each time, so hopefully they will last. Can tell you I ordered 4 bags of 100, & was shipped two bags each of differing lot numbers. The consistently in weight within lot were satisfactory for my needs, but they were a little far apart for my liking between the two lots. I’ll just run one lot till the croak, & switch to the other. Shot my first PRS Match over the weekend, & did ok for never practicing any of the positions. Finished in 75 percentile, so at least I wasn’t last 
. I call it a success! The pic below was my load data i decided on that I verified the day before the match while checking dope. Nosler Brass, FedGM210M Primers, & 135g Classic Hunter Bullets.
. I call it a success! The pic below was my load data i decided on that I verified the day before the match while checking dope. Nosler Brass, FedGM210M Primers, & 135g Classic Hunter Bullets.
It's in stock at one of the retailers I frequent... That means it beats the hell out of everything else right now.
Mike
Mike
Was in a bind for brass, & all I could find at the time. Pleased so far tho
I run Nosler in my 300 WM. Mainly because Lapua hasn’t become available yet
Have been 100% satisfied with Nosler. To this point I’d consider it my 2nd to Lapua based on my experience
Have been 100% satisfied with Nosler. To this point I’d consider it my 2nd to Lapua based on my experience
I needed some in 6.5cm when I recently added a rifle chambered in such…..it was available and I bought 200 cases.
A week later Lapua showed on the radar. Go figure, right? This current market is nuts.
I need some .308 & .270Win. Didn't want to unknowingly keep adding mediocre quality overpriced brass, but it sounds like Nosler is decent-to-good.
Hell, I’m getting back into handloading again after a long absence……Winchester brass may be all the “quality “ my arse needs.
I‘m not currently set up for annealing but I am definitely going to do so. Just trying to get my head wrapped around what will be needed (as well as my wallet).
A week later Lapua showed on the radar. Go figure, right? This current market is nuts.
I need some .308 & .270Win. Didn't want to unknowingly keep adding mediocre quality overpriced brass, but it sounds like Nosler is decent-to-good.
Hell, I’m getting back into handloading again after a long absence……Winchester brass may be all the “quality “ my arse needs.
I‘m not currently set up for annealing but I am definitely going to do so. Just trying to get my head wrapped around what will be needed (as well as my wallet).
Last edited:
Only have a couple firings on my first try with Nosler 6.5 Creedmor Brass, but so far so good. I do anneal each time, so hopefully they will last. Can tell you I ordered 4 bags of 100, & was shipped two bags each of differing lot numbers. The consistently in weight within lot were satisfactory for my needs, but they were a little far apart for my liking between the two lots. I’ll just run one lot till the croak, & switch to the other. Shot my first PRS Match over the weekend, & did ok for never practicing any of the positions. Finished in 75 percentile, so at least I wasn’t last
That graph readout looks beautiful.
Tight !!!!!
If i could have purchased some RWS 300WM brass at the time i might have something better to compare it against.
Similar threads
Reloading Equipment
Reloading bench cleanout
