SAM-R Question

[eodcam]

Thinking about doing another "tribute" rifle, ok, clone. I want to have a SAM-R built. Anyone know what year PWS built them and if any of them had the gas blocks secured by set screws and milled barrel flats or if they all used tapered pins? I only wonder this because if they were based on PWS rifle team service rifles, would they have used the barrels they had on hand to build the first ones, which would have probably had screw flats. Any thoughts?

 

[Afghanvet09]

I'd try arf.com on that one. Never seen a post on SH about a sam r build. SDMR, MK 12 mod 0, 1 I have seen clone builds on here with specs. I think what stopped me was the front sight assembly specifically where to find.

 

[sinister]

June 2003
Analysis Report 03-20
Marine Corps Warfighting Lab, Quantico, Virginia
Squad Advanced Marksman Limited Technical Assessment
Target Identification and Precision Fire Testing
Wendy R. Trickey

Appendix A: Rifle configurations

The following pages show lists and figures of the configurations of the 5 SAM-Rs and 3 M-16 A4s that we used for this testing. The SAM-Rs are numbered for reference to table 1. We assumed that there was no difference between the rifles’ performances. However, the precision values from SAM-R 1 were found to be significantly worse (by more than 20 percent) than the other SAM-Rs (t-test, p < 0.03). The figures also show the optic used with each SAM-R. All SAM-Rs were built to the 2-MOA specification. They were new, with no more than 150 rounds through them. They were fitted with Harris swivel bipods HBLM-S and A.R.M.S. quick release bipod mounts.

SAM-R 1
• Olympic Arms FIRSH free float tube
• Colt heavy barrel, chrome-lined, 1:7 twist
• No flip-up sights
• KMC scope riser rail
• KMC low profile scope rings
• Standard flash hider
[IMG2=JSON]{"data-align":"none","data-size":"full","src":"http:\/\/i47.tinypic.com\/98g80m.jpg"}[/IMG2]
Figure 22. SAM-R 1 with TS-30 A1.

SAM-R 2
• PRI specific parts (Free Float tube, charging handle, pop-up front sight)
• A.R.M.S. rear pop-up sight
• Krieger 20-inch Stainless barrel 1:7 twist
• A.R.M.S. SPR full length rail
• KMC low profile scope rings
• Standard flash hider
[IMG2=JSON]{"data-align":"none","data-size":"full","src":"http:\/\/i49.tinypic.com\/2nu22v8.jpg"}[/IMG2]
Figure 23. SAM-R 2 with TS-30 A1.

SAM-R 3 and SAM-R 5
• KMC Free Float Tube (FFRAS)
• Krieger 20-inch Stainless Steel Barrel with 1:7.75 twist
• KMC riser rail
• KMC scope rings
• KMC front folding sight
• KMC rear folding sight
• Standard flash hider
[IMG2=JSON]{"data-align":"none","data-size":"full","src":"http:\/\/i50.tinypic.com\/1zgug5i.jpg"}[/IMG2]
Figure 24. SAM-R 3 with ACOG.
[IMG2=JSON]{"data-align":"none","data-size":"full","src":"http:\/\/i47.tinypic.com\/10p67a1.jpg"}[/IMG2]
Figure 25. SAM-R 5 with ACOG.

SAM-R 4
• KMC Free Float Tube (FFRAS)
• Douglas Chrome-moly Heavy Barrel with 1:8 twist
• KMC scope riser rail
• Badger low profile scope rings
• Standard flash hider
[IMG2=JSON]{"data-align":"none","data-size":"full","src":"http:\/\/i48.tinypic.com\/11w809v.jpg"}[/IMG2]
Figure 26. SAM-R 4 with TS-30 A1.

= = = = =

What eventually fielded (only around 100 rifles)

[IMG2=JSON]{"data-align":"none","data-size":"full","src":"http:\/\/img150.imageshack.us\/img150\/4494\/m16a4samrdetail2.jpg"}[/IMG2]

 

[eodcam]

Awesome! Thank You! This helps make some of the info I've been finding make more sense! Thanks Again!

 

[kaotic504]

I always thought the SAMR had a knights flip up gas block/sight

 

[eodcam]

In the End I believe it was.

 

[jn_fsu]

I own a rifle that I built the lower. I bought a BCM 410ss 16" upper.
Specs on the upper
Features
M4 Feed Ramp Barrel Extension
M4 Feed Ramp Flat Top Receiver
T-Marked Upper Receivers
1/8 Twist Rates
5.56 NATO Chamber (USMC SAM-R)
410 Stainless Steel
HPT (High Pressure Test) Barrels
MPI (Magnetic Particle Inspected) Barrels