Gotta let this optic go unfortunately. A hunting reg change in my state eliminates my need for it.
These are fairly difficult to get a hold of

This has been handled gently but never outside the house or on a rifle.

Why is it that I have over a dozen RMAs of scopes and lasers over the last three years because of faulty electronics? This is really getting out of hand. On my 4th or 5th RMA of an IFS scope and about the same number of returns of a TOR Fusion laser/light combo that is currently being worked on yet again. I have 3 or 4 of the TOR Fusions and not one of them has not had to be RMA’ed.

I have never had this much difficulty with any manufacturer ever. Everything I have purchased from them with a battery I have had to return.

I finally asked them to just refund me on the scope since they didn’t even bother to test it more than 5 seconds. It is still screwed after they sent it back ($25 worth of shipping later). Not sure how I could be more frustrated with a company I really wanted to like and puts out nice (non-electronic) scopes. Waiting for them to tell me to go pound sand on the refund which I fully expect given their lack of interest in fixing their products.

Has anyone put a Ruger 10-22 with a Gemtech Mist-22 barrel in a Luth-AR MCA-22 chassis?
I talked to them and they sent me a file showing where to trim the chassis to make the barrel fit so I know it fits but they were not sure if it is possible to remove the barrel/suppressor shroud from the gun without removing the gun from the chassis first.

Zermatt Origin with Bartlein 18” 1:10 barrel chambered by Red Beard. Foundation Dominion natural with full length Arca. Hawkins M5 dbm with MDT metal 5 round mag. Triggertech special single stage pro curve. Switching to all lefty after 48 years, no trades unless LH bolt stuff. $2200 shipped my FFL to yours.

I'm wondering if anyone has successfully changed the non adjustable cheek riser chassis to an adjustable with thumb wheels? I just picked up a used folding ultralite that has a fixed cheek piece and wanted to swap it out if I could. I see MPA has some spacers and a buttstock replacement kit I might be able to use but have to wait till Monday to call them directly about this.

Thank you.

I have a Like New Geissele Super Precision 30mm Scope Mount. This is the discontinued SR25 version and these are really hard to find. This is a Must Have for all of you Knights SR25 owners.

I just sold my Knights SR25 Match Rifle and no longer need this Mount.

Only $269 Shipped.

ARC Gen 2 Nucleus with 20 moa rail. Criterion 25” 1:7.5 barrel. McMillan A5 stock, triggertech special single stage flat trigger. Hawkins M5 dbm with Magpul magazine. Weighs 10.5 lbs. Less than 300 rounds, shot factory Berger .5 or less. Switching to all lefty after 48 years. No trades unless it’s LH bolt stuff. $2200 shipped.

As my question states- I do not see a lot of use of Accurate 2520-
Is there a reason it has fallen from being used more frequently-
If I am correct was 2520 not designed around the .308Win round?
Maybe someone with more experience with this powder can give a solid answer-

Leupold Mark 4 12-40 Spotting scope, with TMR reticle. No boxes or papers but in great condition. Second owner. Comes with Badger SLICK kit and Badger cover for it. $1,500 OBO. The SLICK kit is missing one of the picatinny sections and the base, so it has 3 total. The previous owner lost it. I have an ARCA plate on the bottom.

If anyone has access to any facial recognition technology and would like to do a brother a favor, I’d be much obliged if someone could find me a name to this fine upstanding citizen who stole my kid’s dirt bike. I know it’s a long shot but worth a try.

If it helps, he lives in the Fairburn/Union City area. South West Atlanta.

About 12 months old. Upgraded to a V4. Fairly sure I don't have the original box. $325 shipped to lower 48. Shipping is going to kill me on it so don't low ball me. Buy new at retail.

Away from home but can post pictures and or videos of it working later.

PP f&f or we can work out a trade. I shoot in the MOST series just about every match. Happy to bring it to a match.

Trades: Berger 109s, 105s, SF dual fuel weapon light, .44 bullets.

NX8
4-32
MIL-XT

Mounted on a Geissele 6mm ARC, zeroed and haven’t had time to shoot it.

$1800 shipped

No trades

NX8
2.5-20
MIL-XT

Mounted on a Proof .22, zeroed, put away

$1600 shipped OBO

No trades

FS

Bought 500 of the Sierra 80gr SMK to try in a 223 bolt gun. Shoot great, but sticking with the ELD.

Shot 58 in total, 442 remaining.

$150 shipped

Factory LMT MWS 6.5cm SS 1/8 rifle length barrel cut down from 20” to 16” by D. Wilson Mfg. Runs flawless suppressed/unsuppressed. Would be perfect for a 15.3” upper. Less than 40rds through it, will come with factory gas block and tube. $750 shipped NO TRADES

FFP, illuminated. Excellent condition, aside from a small spot from rings, shown in pic.

Glass is like new.



Spot.




Ships in original box with accessories.

$825 shipped CONUS. Prefer DISCRETE PP F&F, open to some other options.

Itching to get our young into a global conflict.

The amended bill states:

Automatic Registration: The Military Selective Service Act (50 U.S.C. 3801 et seq.) is amended by striking section 3 (50 U.S.C. 3802) and inserting the following new section 3:
“SEC. 3. (a)(1) Except as otherwise provided in this title, every male citizen of the United States, and every other male person residing in the United States, between the ages of eighteen and twenty-six, shall be automatically registered under this Act by the Director of the Selective Service System.

Click to expand...

Click to expand...

“(2) This section shall not apply to any alien lawfully admitted to the United States as a nonimmigrant under section 101(a)(15) of the Immigration and Nationality Act (8 U.S.C. 1101) for so long as he continues to maintain a lawful nonimmigrant status in the United States.

Click to expand...

https://www.thegatewaypundit.com/20...-house-representatives-passes-bill-automatic/

Anarchy Outdoors CZ 457 +3 Round Extensions (5 for $50 TYD USPS Priority). Like new, installed tonight and would rather just keep my magazines factory. PayPal friends and family with no note.

I currently have a RCBS Pocket 1500 and is terrible with the drift. Picking the powder pan up and placing it again shows drift as much as 0.3gr and goes back and forth so there's no way to judge what is the correct reading.
No drafts, wiped the thing with dryer sheet and as away from electronics as possible but the issue is still there.

Other than the beam scale, is there an electronic one that won't drift? Preferably with an auto trickler but not a necessity.
Budget is less than 300USD. That being said, I wouldn't want to spend 300 only to find out that I need to get a fx120 for reliable measure, so if I absolutely need to spend more, let me know and I'll delay my purchasing.

Thank you

Basically new, mounted and never left the safe.
$125 shipped.

Does anyone in the Phoenix are know where I can go to shoot water-marked targets at 500-1000 yards? I recently built a new rifle and need to zero and true my data. Any help would be appreciated. Thanks!

Leupold standard one-piece bases. These were in a big ol box of shop clean out stuff, they could be a year old, they could be 15 years old. There may be a screw missing but havent looked close enough to confirm. I think they list around $35-40 these days, so the $25 price tag on them may mean they're vintage, which would totally make them worth a lot more. Of course. Or...be good basis for an "inflation in the gun industry" discussion.

(2) 55705 - Savage 110, right hand, long action, silver
(2) 50161 - Remington 700, right hand, short action, silver
(1) 50007 - Remington 700, left hand, long action, matte

$25each, shipped

Or if someone wants all five, $100 shipped.

Or trade for something cool. Actually, that'd be the best option

Trijicon RCR, light use. Was painted and stripped, 98% of the paint is gone. Fully functioning, nice dot, just overkill for what I bought it for. Full disclosure, one of the capstan screws cracked between two of the holes upon removal of the optic. I have emailed trijicon regarding replacement screws, but they also sell them on their site and it probably wouldn't hurt to just buy a new set (there are 3 different lengths for different pistols anyway). I do not have the box or torque card as I purchased it without them from somebody who had barely used it. Let me know if you have any questions. Only trades would be partial trade for a 508T x2 red or RMR, Monsoon ported M&P 4" 2.0 slide. I can send any additional photos needed.

$610 net to me

Anyone got a good source on getting some new magazine springs to 10 round 22 LR mags (not the detent spring and pin that keeps the bottom on)