Yes I can ship.
2000 federal 205 150 bucks shipped
1 jug of h 4350 325 shipped

Yes I can ship them.

No trades

Vortex Strike Eagle 3-18x44 MOA

$625 for SE (still have the box)
MOUNT NOT INCLUDED.

Was on a 6 Arc that didn’t get used much.

Never used Whidden .300 PRC Click Adjust Adjust FL Bushing Sizer die. Excellent condition. Asking $100 shipped and insured with payment via Venmo. Tracking to follow ASAP.

Please PM if interested. Happy to FaceTime for verification.

$550 shipped. Used this for a couple coyote outings, still in excellent shape. I did notch the rear of the handguard for my origin rail and cut the length down to fit my 16.5” barrel. Has action screws, no grip. Rifle that was in it was Zermatt Origin with 16.5” proof barrel.

Used American Defense 30mm mount, 0 MOA. Excellent condition. Asking $175 $125 shipped and insured with payment via Venmo. Tracking to follow ASAP.

Please PM if interested. Happy to FaceTime for verification.

Have an excellent condition (like new in box) Leupold mk5 3.6-18. Model# 180725 PR1 Mil reticle. Illuminated.

I took it out of the box and had it sitting in some rings lightly, but never shot or used beyond that.

$2100 shipped and insured.

I have a 20” Tikka CTR in 6.5 Creedmoor. Painted the stock a while back. Comes with TBAC compatible brake, flat faced trigger, and two CTR mags. $950 + shipping or local meetup (Lincoln NE).

Probably has 500rds down the barrel, and is more accurate than I am. Typically shoot 140 ELDM or 130 Bergers federal ammo.

Can’t remember if the rail is 20 MOA or not, but I did cut the rail down for a scope to clear. Works fine.

i have 349 pieces of once fired 6gt brass, not prepped.

looking for $200 plus the ride.

Never used Redding Competition - Bushing Neck Sizing 3 die set. Excellent condition. Asking $150 $170. shipped and insured with payment via Venmo. Tracking to follow ASAP.

Please PM if interested. Happy to FaceTime for verification.

Manners TCS

Sold

I know this is a long shot, but does someone have a left-handed Bergara B14R action they want to sell? I don't need a barrel, but if it is barreled, that is fine.

Is it possible to have the angled corrected drops appear in the bino screen?
When I range a target with say a 25 degree angle, I get the line of sight dope, I get the AMR distance but I have to put the AMR distance into Quantum manually to get the correct dope.
Can I get the AMR dope, without having to do a separate process?

List attached as a picture.

Used mostly for loading all my PRS 6GT ammo, saves a ton of time on brass prep and powder + seating if your trickler(s) can keep up. Produces very high quality ammo.

Also have toolheads configured for 9/223 bulk loading.

Located in east TN, really prefer a meetup vs. shipping. Can meet at Coleman Creek NRL hunter in a few weeks, and willing to travel within a reasonable distance to get a deal done.

If someone wants it shipped, I'm willing to work that out too, just not my first preference.

Not looking to separate/part out.

Happy to get on a call etc to chat about it.

$2500

I was loading 308win today. Cases are Lapua on their third loading. FL sized, and trimmed with the Dillon rt1500. I put a Lyman M die in station 1 of the loading toolhead, because everything I read said that I would not need to chamfer. Somewhere I went wrong. I was seeing copper shavings after seating. Then re read M die directions, and it said to flare 1/16" at mouth. I am guessing if I go this route I will need to crimp said brass after seating? I had gone this route because everything I had read says the Dillon size/trim die really shrinks the neck and that I needed to expand it back up to .306 and that the M die would do it and also eliminate chamfering. WIN WIN, or so I thought.

The questions I have now are

1) how bad is this going to affect accuracy?
2)Should I just go back to chamfering before going onto the loading toolhead?
3)Is their a better die for this job than the Lyman to expand?
4) Is their a better die to trim with than the Dillon?

I'm loading up 2500 or so rounds for a belt fed 1919, using cloth belts. When I seat the bullet to 2.8" (actually 2.790") I'm still .06" or so short of the cannelure. If anybody can measure a NATO ball/FMJ round for me and tell me the OAL, that would be great.
I may have a mix of pulled/new 308 and 30-06 bullets and I do have a mix of FMJ, API, AP and tracer bullets. This does complicate things, but if I get the OAL for a FMJ, I can go off of the ogive for the others.

Doing some bullet clean out, prices do not include shipping

i have the following

700 108 ELDM same lot - $200 -SOLD
500 109 ELDM same lot, came loose packed from GAP - $150 - SOLD

500 Berger 108 EOL same lot - $200 - SOLD
400 Berger 95 VLD, and 1 box opened, looks like roughly 50 left, same lot - $150

1000(ish) x-treme 124gr 9MM, one box opened, unsure if any were used
250 Berrys 124gr 9MM
250 Berrys 115gr 9MM
All 9MM - SOLD

500 175 SMK - $150 - SOLD

How hard is it to disassemble and reassemble?

Garage level stuff or send it out level stuff?

$40 shipped

Friend got an armalite ar10b when his dad passed.

He wants to use pmags in it to match other rifles he has.

He asked me if he could change the lower to work.
My initial searches it looks like the ar10b upper needs a modification to work with pmags?
So change the lower, AND modify the upper?
If that is the case then maybe it would be best to just buy more of the mags that fit the B and leave it as is?

Thanks for any input.

I had Lee custom make a seating plug for 140 gr ELDM’s and by the time it came, i had switched calibers to 6mm GT.

$18 shipped.

Vortex Impact 4000

Like new condition and comes with everything as it did new.

This has only seen 2 range sessions and is in perfect condition.

Asking $sold

Excellent condition, with almost no use. Stock, no upgrades.

Will include some bits and bobs - a couple mags, some barrel shims, stuff like that. Getting out of the 10/22 game.

$900 shipped from my FFL to yours.

Arken EP5 5-25x56 FFP Mil.
Comes with .092, and 1.26 rings, sunshade, flip caps, rubber bikini caps, turret tape, and throw lever.

Looking for $500 shipped.

As shown. Missing piece is missing. Maybe one of you with better welder-fu than me can make a repair?

$40 delivered by usps.

I have a Curtis Axiom 6GT barrel. Approx 850 rounds. Was running 115 DTAC @ 2780, ES-8.5, SD-3.3.

RCBS Matchmaster Dies w/ .266 bushing, and 6GT modified case.

Little crow, and Lee case trimmers.

Looking for $350 for everything above shipped.