ACRO P2
FDE
3.5 MOA

NEW, never mounted

$550 shipped and insured

No trades

Thanks

So I’m a terminus fan for sure. Love the quick change, 60 degree bolt throw, threaded trigger pins, and they look cool as shit. So I built out a Gucci rifle and picked up a titanium nitride (I think) action.

Well fuck me… I haven’t shot this yet (barrel is a 22gt and haven’t loaded anything yet). So I’ve just cycled the action a few times…. But the nitride has already worn off where the bolt slides. I reached out to Joel, who’s awesome and a great guy, and he said it’s normal wear.

I thought these were supposed to be hard as shit. None of my dlc or black nitrided actions wore anywhere near this quick.

Thoughts? Is this normal wear? There is no wear on the bolt at all.

Nightforce ATACR Tremor 3
7-35
FDE

Comes with everything as new.(sunshade, windage ring, throw lever)

Mounted in a SPUHR mount on an AXSR.

$2950 shipped and insured or best offer

Not looking for any trades, thank you.

Wanting to sell my ASA M24 clone. Built on an ASA m24 receiver, with matching bolt. Has a correct m24 trigger, sunny hill floorplate, and HS precision PST 024 Stock. Includes correct 1 piece base, leupold mark 4 rings, correct harris bipod. Was barreled in 3006 by Douglas Barrels in Charleston WV. 100 rounds down the pipe. Will include 70 rounds primed brass twice fired brass. Nightforce scope is not included. 2400+shipping.

Would be willing to partial trade xm3 clone parts.

I bought this as a 6 digit M40 donor. My plan is to use the receiver and bolt and sell off the rest to recoup some funds. To me, it’s just someone’s old custom varmint or BR rifle. Any reason not to dismantle it? In other words, is it from a prestigious builder or does it have any value beyond the sum of its parts. It came from one of the big flat states in the middle if that gives any context. Very odd and specific build for sure. But beautiful wood.

Left hand thumb hole, right hand action, bedded as a single shot. Octagon barrel with round receiver end. Is that a 40X trigger? The only identifying marks are “ 9 9 70 ES” under the barrel. That stamp left a nearly perfect impression in the bedding material.



I’m not soliciting offers, just some insights, thanks,

Greg

Is a lot tested group like this as good as it gets or would throwing on a tuner tighten it up even more? Been debating testing a Harrels on this, but not sure if it’s worth the time and money or just to continue to extensively lot test until I get these results.

5 shot group at 50 yards grouping .257 and 10 shot group at 100 yards grouping .635

CZ 457 with 21 inch lilja in MDT ACC Premier Gen 2.

Primarily shoot NRL/PRS. Wasn’t sure if the tuner would primarily address tightening up more of those “pretty good” lots but be marginal (if at all) on improving lots like this.

Right Hand Action
30 MOA Scope Mount
Custom 5X5 22” Percision Barrel
Trigger Tech Single Stage Flat Diamond Trigger
Two Factory Mags one with Factory Extension
Spare factory bolt parts including fire pin and springs

Action & Barrel has less than 300 rounds through it!

$2200 plus shipping or best offer
(To your FFL)

For matches, I know a lot of people use the mark 5hd’s, but how about the mark4hd’s? I’m looking at the mark4 hd 6-24 (pr2-mil), and the Bushnell dmr3 3.5-21 (g4p). Looking at both as lightly used scopes currently available for under retail in my area.

I’ve ruled out the xtr3. Used a gen2 razor for awhile, but its reticle was just a bit too fine for me on the lower 10-14x powers. I also used a sig tango 6 4-24 for a while and although most didn’t like it I loved its glass, just hated the mis-alignments of the #’s on the turrets, and they were spongy.

I also found an Xrs3 for a great deal but I’m concerned about the writings I’ve found saying it’s horrible in mirage and harder to focus(?). As well as the reticle not being very usable in the 10-14x range since it’s got such a high power of 36x

Camouflaged with alumahyde about 10 years ago, still looks nice. Floor plate has a small dent. 200+shipping for all.

Found a little data on this load but way to far to apart on grain load to feal comfortable
Read from 29.8 H110 to 33.0 H110
None on LiL Gun but know it's a popular powder for it .
Saturday going to grab me some RL7 so have plenty of options but have a crap ton of H110 so was hoping for the 325 data ,Appreciate any and all the help in advance and thank you..
I have loaded 30.0 - 31.0 - 31.5
31.8 and 32.0 of H110.. If anyone finds the loads seem to hot please speak up and let me know what you think,going to try them this weekend..

Looking to get rid of my very good condition Accuracy International AI AT.

Gun has the pale brown thumb hole folding skins on it. 9.5/10 on pale brown skins. See pictures for the two scuffs.

Also have a full set of green skins for the gun as well non thumb hole. And pale brown non thumb hole stock section and grip. 7/10 on green skins.

Gun has a AI NV bridge
20MOA front rail
20 moa NV height action rail
Front key slot sections on sides
Sawtooth long arca rail with Rlock
Spare pic rail spigot and bipod spigot(installed)
Factory action rail included.
Thumb rest
Lots of spare plugs for both colors of skins.


Comes with a factory AI 6 creed barrel threaded 5/8-24 with about 380-400 rounds on it. 316 reloads and a little under 4 boxes of factory ammo on it.

Asking 4500 for everything plus shipping and insurance. Scope and bipod not included.

I feel like a fool it was recommended from LaRue Tactical use 620 on the LaRue Tactical stealth Barrel threads for my suppressor muzzle brake from silencerco.
I got it shimmed up to where I thought it should be and allowed a little bit of room for torque so I applied the 620 compound threaded the brake on about halfway turned around to get my foot pound foot pound ratchet which took less than 20 seconds and whenever I tried to turn the muzzle device it was very hard to turn and before I can make it to where the muzzle device was perfectly flush and even it was Rock Solid.
Loctite claimed they had a 60 minute set time but in my experience just now it was a 40-second set time.
With the shims I am just a smidge off from being level on the muzzle brake if you weren't paying attention you probably wouldn't even notice that it was a little crooked.
My concern is whether or not when I put my can on if it's going to cause a baffle strike in the end from being slightly off the center axis if the shoulder doesn't meet up with the muzzle brake well enough.
Not sure if I can just wait until I get my can out of jail and put it on and run a clean Rod up through the door and Center it the best I can in the back of my action and see if there's any run out or not.


I feel like im fine like there's enough contact between the 90° on the barrel the shims and the 90° on the muzzle brake but I'm anal about this kind of thing and I feel like I might be overthinking it LOL.


As a little side note I know it's making contact with the shims because I can't even budge them which is what leads me to believe they are probably making full contact with both 90° surfaces therefore leveling the muzzle brake to the bore.

I'm really thinking I should have just used the rock set that came with it now LOL.

It's been many many years since I posted here so hopefully you all are just as nice as you used to be and don't eat my ass up for this question thanks in advance and hope you all are having a great day

Less than 1000 rounds through this right handed 737, .308 bolt face, comes with a Bix N Andy Dakota. NOT AW cut, just runs AICS SA magazines. Excellent condition, ships to your FFL.

$1300 shipped with trigger included

1100 rounds of 190s. $2800 shipped

In like new condition. No box but do have the spec cards. $950 shipped

Left over from a previous scope thats long down the road. Should fit any 56mm NF. $25 shipped

$700 obo shipped conus

Howdy Folks,
In my quest to build a M40 replica, many searches have brought me to this site. I don't intend to bore you Folks with another M40 build but I will have questions. I have no delusions of thinking I am or could be a Sniper, hell I can hardly see my...when have to..., never mind I've just wanted a M40 for about 30 years. Kids, schools and two college tuitions have stood in the way. All have been paid off, now its my turn.

NIB Springfield Prodigy 4.25”, 9mm, optic ready. Comes with (3) 17rnd mags (normally ship w/ 2). Mags were used in another gun, but are in excellent condition. $1350 shipped. PPal FF, Apple Cash, US postal MO. Gun will ship from my FFL to yours.

Will consider trades for quality bolt short action or barreled action w/ standard bolt face. Quality LPVO (NF ATACR 1-8 preferred). Plus or minus cash on either side depending on deal. Happy to answer questions. Thanks for looking. Nick-

Hello,

I recently bought a used BAE UTM thermal and would like to have a manual but can not find any downloads online. If someone has one of the manuals would you care to post some pictures or DM me?

Thank you!

The question is have we entered the portion of the life cycle where the inflation of fiat currency is strangling Joe Sixpack, regardless of the generation?

Login to view embedded media

Like new leupold mark 5 5-25x56 TMR reticle with Hawkins ultra light rings, bought to throw on my 22 creed then after a month went to a thermal and it’s just been sitting in the safe. Come worth box and all factory stuff. Only trades would be for a NX8 4-32x50 F1 mil. 1850 shipped. PayPal f&f, Venmo, cash app

Looked at the Hodgdon data for H110. 16" barrel, 1060 fps, 9.6gn and 2.05 OAL.

My barrel is 11 inches. That should give me 920-960 fps. So I did 10gn of powder. Trying to ride the line and all.
Chrono'd it. 1200+
Not sure how I messed up my calculation that badly.

All Zermatt actions discounted. Add to your cart for pricing.

www.frontrangeprecisionllc.com

Mpa matrix for r700 short action right handed, full arca rail and bridge, has both forend weights and rear stock weight, great condition like new. Decided to go a different route 850 shipped. PayPal f&f, Venmo, cash app