Time for a new Dillon Reloading Machine
- Thread starter CaptNemo
- Start date
If there aren't any hide vendors, https://www.scheels.com/p/dillon-precision-xl-750-reloading-press/4235-750.html has 223 and 45 ACP in stock right now.
I just ordered one from Scheels. I would have rather purchased at Bobcatarmament but Scheels had them in stock.
They have one less in stock.
I saw the response in the thread and pulled the trigger !
Thanks Guys !!!!
I saw the response in the thread and pulled the trigger !
Thanks Guys !!!!
Hopefully everything.... it's really a do all machine. Everything from bulk to 1000yd F-Class...
If I didn't want a savings account, I'd have at least 2
Get the brass feeder and then a Mr. bullet feeder when you can afford it. You’ll be able to do 100 rounds in about four minutes. Probably loaded over 100,000 pistol rounds on a 650 with the set up. Enjoy it.
Ya no different than loading on a rock chucker other than its way faster
Are you using the Dillon powder drop or do you still weigh charges individually?
I believe the key to precision ammo would be a ball powder such as Staball or ramshot Hunter on the Dillon
Do it both ways depending on the situation . Powder choice makes a big difference on when you can use the Dillon powder meter. Ball powders and short stick powders like 8208xbr meter extremely well
I load my 6.5cm on my 550, but I unfortunately do not have a 750. I do manually drop through a funnel rigged up in one of the toolhead stations. I have two modified Chargemasters that can easily keep up with as fast as I can load quality ammo.
That being said, there a many competitors from all disciplines, including 1000yd F-Class who load on 550/650/750's
I've never been sure where the notion that Dillon's can't load precision ammo came from.
That makes sense. I may have to try it out on my 650. Personally, I don't trust the Dillon powder measure for precision ammo, but that sounds like a logical work-around that makes the best of both worlds. Thanks for sharing.
In case anyone else is looking for a Dillon.
I grabbed a RL550C as a spare machine.
www.hyattgunstore.com
I grabbed a RL550C as a spare machine.
Hyatt Guns - America's Largest Gun Shop
Hyatt Guns is America's Largest Gun Shop. We sell guns, gun accessories, custom knives and more!
Que the fuds..." You caint load precision ammo on a progressive...my pappy told me so back in 1974..." Comments
Seriously though...I load everything but 338LM and can't wait to get a second so I have one machine dedicated to large primers and the other dedicated to small
Well, ya....but they're different calibers. I load precision 6.5cm, 223, and 223AI on my 550 using Armanov clamped toolheads w/ floating dies.
The toolhead on the left, I'm experimenting with doing it all in one step with my 6.5. Tumble my fired cases for an hour, load em in trays of 50 and spray em down with One Shot and load:
Station 1: deprime/size/prime
Station 2: Mandrel to set neck tension to 2thou
Station 3: Manually drop powder
Station 4: Seat.
I loaded up 200 a week or two ago and I'll get to the range later this week to see if they're as consistent as the two toolhead setup
So far no, I just put 50 on a towel and roll em around and wipe em down. But this is the first 200rnds I've done all in one toolhead like this. Normally I do two toolheads, so I would tumble the cases after brass prep.
I don't think I'd have an issue tumbling loaded rounds as long as there weren't a lot. It only takes about 10 or so minutes in fresh polishing media to take off the lube.
That explains it.. I'm using two tool heads for 308. one for prep and one for powder and seating.
I would normally, but I'm trying a one toolhead setup to see whether it works, and if I prefer it. The two toolhead setup is pretty efficient, and not sure if I really like the one toolhead. Trying to jam too much into one operation sometimes has its drawbacks
How well does the Dillon powder drop do with varget and other longer extruded powders?
I've only used ball/flake powders on my 650 so far
Lol... the fix IS the 750. The 750 has more meat to it as a press, its priming system like mentioned is substantially better, the same as the 550. It also has a different indexing system on the shellplate that is smoother and less prone to "jumping" on you and losing powder out of cases that are almost full.
Heres a good video....
Similar threads
