• The Shot You’ll Never Forget Giveaway - Enter To Win A Barrel From Rifle Barrel Blanks!

    Tell us about the best or most memorable shot you’ve ever taken. Contest ends June 13th and remember: subscribe for a better chance of winning!

    Join contest Subscribe

Recent content by cobbonthecorn

  1. C

    Rifle Scopes Switchview for Schmidt Bender PMII 5X25

    Nice lever!
  2. C

    Rifle Scopes Switchview for Schmidt Bender PMII 5X25

    Thank you for the confirmation. Looks like Jet has them for $47 free shipping and 15% off that price on your first order making it less than $40.
  3. C

    Rifle Scopes Switchview for Schmidt Bender PMII 5X25

    Just took possession of a Schmidt Bender PMII 5X25 with the index knob that is bumpy. MGM has model 1650SV that generally has the correct dimensions. Anyone have experience with this specific switchview or a recommended switchview for this S&B? Thanks in advance!
  4. C

    Recoil Pad for 338 LM

    Thanks for all the input. I have gone with the Kick-eez dual action 15/16 thick recoil pad. The decision came down to two important considerations, can the pad fit/be ground to fit the chassis, and can I put an additional hole through the recoil pad to access the butt plate adjustment screw...
  5. C

    Recoil Pad for 338 LM

    Yet another contender.... tks!
  6. C

    Recoil Pad for 338 LM

    Thanks for the input so far. I'll be at the range trying weight and brake, then decide how much pad I need. Again, thanks!
  7. C

    Recoil Pad for 338 LM

    If it were only that simple....
  8. C

    Recoil Pad for 338 LM

    How about the Pachmayr 990 (Pachmayr&reg Pachmayr your primary source for quality handgun grips and recoil pads)? Similar to the 550. gewehr- Which kick eez have you used?
  9. C

    Recoil Pad for 338 LM

    Just wrapped up a newly built 338 LM and do not care for the recoil pad that came with my chassis. (Almost no padding.) I'm at a complete loss after looking at some of the choices on the market. Have heard the pad can be too soft or too hard, can mess with accuracy, can cause vibrations,etc...
  10. C

    Wanted: Brass Annealing Times

    Info so far is just what I was looking for... To an earlier question, the 20 seconds was just to demonstrate my range of control so far. As for the machine posted by ARNIE19, that is what I have started working on. Use straight sided cake pans instead, really simple and the circular run-out is...
  11. C

    Wanted: Brass Annealing Times

    All, thank you for the inputs. I have design options that I think will work for 2 to 20 seconds, and 1 or 2 torch heads. You have confirmed that I will need the full range to be successful. Once the machine is up and running I'll share cost and design information, including why some of the...
  12. C

    Wanted: Brass Annealing Times

    p.s. I have read multiple threads and have become familiar with the process of setting temperatures, etc. If anyone has done 223 it would be interesting to know your cycle times. The machine being built likes slow speeds so larger cartridges should be easy. But as it speeds up the automatic...
  13. C

    Wanted: Brass Annealing Times

    ORKAN- Thank you! I get the fact that everything matters, I just need to know a ballpark so I know if I can use automated feed system based on mechanical linkages or if I need solenoids. With one torch I can use mechanical linkages. I will post the results of my project when it is complete.
  14. C

    Wanted: Brass Annealing Times

    I am in the final stages of building a brass annealing machine and need timing information to get the rotational speeds set. For a single torch set-up, how much time in the flame do you anneal 223, 30 and 338 cartridges? How about the same for a two torch set-up? Are two torch heads really...
  15. C

    Giraud Annealing Machine Modifications

    I'm working on an annealer and would like some information if anyone would share. What is the 20lb tank pressure when it is full? With Benzomatic torch heads (self regulating) where are you setting the regulated tank outlet pressure going to the torch heads? How big a difference does this...
See more
Top Bottom
Back
Home
Forums
Merch
Alerts