• Winner! Quick Shot Challenge: What’s the dumbest shooting myth you’ve heard?

    View thread

Recent content by dbutler

  1. D

    Range Report Burger bullets

    Re: Burger bullets I have a Douglas air gage and we measured with a chamber length tool. The OCL was 2.75 and I loaded 2.65. The barrel is 1in 8 twist and 26inches long. My home alt. is 647' at standard barometric pressure wind is generally from the south east at 10 miles per hour. I am...
  2. D

    Range Report Burger bullets

    Re: Burger bullets I didn't look that close so you may very well be correct at the 140 gr. The Berger rep printed the information off the Berger site so you may have access to the same info that he told me. Thanks for you imput
  3. D

    Photos Arctic Snow Ghillie

    Re: Arctic Snow Ghillie I have made three suits and this one is great. Job well done
  4. D

    Range Report Burger bullets

    I just received a box of Burger 6.5mm 142 gr match bullets. I recently spoke to a person with Burger and told him I didn't seem to get the result I was looking for with their bullets. He asked a couple of questions about my reloading and said that I should try to jump the bullet. 10 thousands...
  5. D

    Rifle Scopes Zeiss conquest comment

    Re: Zeiss conquest comment The Zeiss Conquest series is made in the USA with Zeiss parts at the Meopta factory. The glass and parts are shipped in and the finished product is made in USA saving the end user tariff and international taxes. I own 7 Conquest scopes and have never had a...
  6. D

    Rifle Scopes Mil MIl vs. MOA mil

    Re: Mil MIl vs. MOA mil Sorry but I was of the impression that a Mil Dot reticule is in mils and a 1/4 in adj was in MOA
  7. D

    Rifle Scopes Mil MIl vs. MOA mil

    I am sure this has been discussed many time I just don't no where to look. Appreciate an addy to set me in the right direction
  8. D

    FREE Mesquite Creek Rifle Match, TX ***PICS UP***

    Re: FREE Mesquite Creek Rifle Match, Texas 02-19-11 I shot my first match here. Great people, great host, great sponsors and fab prizes. Wonderful event
  9. D

    steel targets

    I can shoot at a place that will allow up to 900+ yards I have enough RA targes to reach 600 can I use mild or cold steel for the further ranges without having any problems. Standard lang range calibers no magus. thanks Dave
  10. D

    Steel targets

    I am setting up a range on a piece of property that will be able to have 900yd to 1000 yd distances. My question is; is there a point in distance that mild steel plate will handle 308 win 260 rem and other calibers generally associated with long range shooting. I have a piece of 3/4 in thick...
  11. D

    FREE Mesquite Creek Rifle Match, TX ***PICS UP***

    Re: FREE Mesquite Creek Rifle Match, TX ***PICS UP*** I shot in the MCR match this past weekend. This was my first match of this nature and style. Adam and Bob, along with the folks they had working to help them, made this a very special day. The mix of experienced, newer shooters and...
  12. D

    Advanced Marksmanship new to long range shooting

    Re: new to long range shooting When you purchase an over the counter rifle to do long range shooting there are a couple of item you may wish to address. 1- Have the rifle glass bedded by a person who KNOWS what he is doing. This should cost between 50 and 75.00 dollars. Doing this will...
  13. D

    Advanced Marksmanship after 600

    Re: after 600 The first indication is that 43.2 grains of 4350 with 142SMK is running about 2850fps. I am on the numbers with my friends shooting a similar load and speed through to 600yds. At that point they are begin to show a flatter path of flight with their rifle. My rounds are...
  14. D

    Advanced Marksmanship after 600

    I am new to tactical long range shooting. I have a Savage model 10 rebarreled to Rem 260. Crony to 2850 and dead on through 600yds. Then things start to go AWOL. I am using a Zeiss 4-12X50 MOA scope. I am handloading with a pharmacy scale to the thousand, three decimals points. Any thought...
  15. D

    Gunsmithing Bedding Remington VTR

    Re: Bedding Remington VTR I bedded mine this evening also. I wraped tape a few turns around the forward pressure point to insure a free float. I bedded out two partition and the barrel lug and forward screw lug. Should know in the morning the results.
See more
Top Bottom
Back
Home
Forums
Merch
Alerts